Vive LVA1030H Foot Stool with Handle Owner’s Manual

FOOTSTOOL
WITH HANDLE
Owners Manual – LVAIO3OH

WHAT’S INCLUDED

• I Stool Base with Pad (A)
• 2 Leg Sections (BI – concave. 82 – convex)
• 2 Handrail Base Bars (CI. C2)
• 5 I Inch Hand Screws (0)

|

• 4 1% Inch Hand Screws (E)
• 9 LocIONashers (F)
• 9 Curved Washers (0)
• I Hanckoli (H)

---|---

ASSEMBLY INSTRUCTIONS

1. Turn Stool Base (A) over with leg attachment holes facing up.
   

2. Fit concave leg section (B1) into a groove on the underside of Seat (A) with screw holes aligned.
   

3. Fit convex leg section (B2) across concave leg section (B1) so that center screw holes overlay. NOTE: B1 And B2 should interlink at the overlapping portion. If they do not, then the legs have been fastened in the wrong order.
   

4. Thread the 1 inch Hand Screw (D) through Lock Washer (F) first then follow it by Curved Washer (G).
   

5. Place down through the center screw hole first. Tighten down securely
   

6. Repeat Step 4 with remaining Hand Screws, Lock Washers and Curved Washers and secure them in the remaining screw holes on all four of the legs.
   

7. Thread 1 % Hand Screw (E) through Lock Washer (F) first then follow it by Curved Washer (G).
   

8. Secure handrail base bar (C1) to the leg closest toward you by lining up the two screw holes making sure that the curved portion of the handrail base bar bends towards the stool base. Place the hand screw through the top hole on the leg first and then through the top hole on the handrail base bar. Make sure you place in far enough to hit the thread on the far side of the handrail base bar hole and then begin to tighten the screw until fully secure and tightened. Thread another Lock washer, and curved washed through the bottom hole on the handrail base and tighten until fully secured.
   |
   ---|---

9. Thread another Lock washer, and curved washed through the top hole on the handrail base and tighten until fully secured.
   

10. Repeat steps 7, 8 and 9 to secure C2 to the far leg.

11. Add the Handrail by pushing down on the two locking pins located at each leg of the handrail and insert down into C1 and C2 until the pins engage with the holes to secure the hand rail.

| |
---|---|---

WARNING

• Our new handrail design features a handrail the leans towards the user instead of away from the user for a more secure experience and a more centered focal point for placing your weight when using the handrail as older models tend to tip due to the handrail facing out.

• When using the handrail you may push down on the rail or in towards the base but never out away from the base of the rail as there is a greater possibility of tipping.

• The rail is there to use as an extra stabilizer to place your leg against. Never shift any weight towards the handrail. Never lean on or over the handrail as tipping may occur.

• It is always recommended to keep your hand in the handrail at an outward position like pictured (need picture)

• Never face your hand inward like pictured as the motion of force in
  most likely to be outward which may cause tipping (need picture)

• Stool has a maximum user weight of 300lbs

• Always stand in the middle of the stool and avoid reaching for items that can cause your balance and weight to shift abruptly.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>