WATTSHOP Anemoi Mk2 Extension System Instructions

: June 29, 2024
: WattShop

Table of Contents

WATTSHOP Anemoi Mk2 Extension System
EXTENSION INFORMATION
BUILD OPTIONS
HANDGRIP SELECTION
UCI HAND HEIGHT COMPLIANCE
STANDARD BUILD
ANEMOI BASEBAR BUILD
CONVERSION KIT BUILD
MOUNT PLATE BUILD
RISER SELECTION
CONVERSION SPACER SELECTION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WATTSHOP Anemoi Mk2 Extension System

EXTENSION INFORMATION

Anemoi Mk2 features include but are not limited to the below

BUILD OPTIONS

Each build option is supplied with three core items; Extensions, Handgrips and Armrests. Additional items supplied are essential but depend on the build option.

STANDARD Core components

Install method

Utilising the adjustable riser, the risers will fit directly to any flat top riser stack with riser stack fore-aft centres between 15-40mm.
WattShop Product Compatibility
This build is not compatible with our
Anemoi riser stack spacers. To increase stack OEM stack spacers should be used.
Can be upgraded to the Conversion Kit and Mount Plate builds.

ANEMOI BASEBAR Core components

Install method

The baseball-specific riser or fixed-angled riser will fit directly to the top of the riser stack.

WattShop Product Compatibility

Compatible with the complete range of WattShop componentry.
Due to the controlled lateral centres of this mounting option, our cross-brace BTA mount and computer mount are the optimal choice for this build.

CONVERSION KIT Core components

Install method

Conversion spacers mount to your baseball or riser stack to convert the centres and profile to enable compatibility.
The baseball-specific riser or fixed-angled riser will fit directly into the conversion spacer.

WattShop Product Compatibility

Compatible with the complete range of WattShop componentry.
Due to the controlled lateral centres of this mounting option, our cross-brace BTA mount and computer mount are the optimal choice for this build.

MOUNT PLATE Core components

Install method

Mount plates attached to your baseball or riser stack to ensure compatibility and reach adjustment.
The baseball-specific riser or fixed angled riser will fit directly to the mounting plate.
WattShop Product Compatibility
Compatible with the complete range of WattShop componentry.
Due to the uncontrolled lateral centres of this mounting option, our single-sided BTA mount and computer mount are optimal choices for this build.

HANDGRIP SELECTION

STANDARD POLE + STANDARD POLE (LONG)

The standard pole handgrip mirrors the traditional pole end shifter. It is compatible with the following shifters:

SHIMANO R9160
SHIMANO SW671
SRAM CLICKS

The handgrips will be available in a standard length for athletes competing under UCI regulations who want to maximise their extension angle and a longer length for athletes competing under non-UCI regulated events.

ERGO
The ergo handgrip is available in four different versions. They are named as follows:

SHIMANO R9150
SRAM WIRELESS BLIPS
SRAM WIRED BLIPS
TRACK

All versions except the track handgrip will be supplied with an inner and outer component. Your shifter button will attach to the inner component whilst the outer component slides over the top. This increases the shifter contact area when shifting.

UCI HAND HEIGHT COMPLIANCE

When competing under UCI regulations you will need to ensure you are compliant with the UCI regulations applicable to your height category.

CATEGORY 1 – riders are allowed 100mm mid-point of the armrest to the extension tip.
CATEGORY 2 – riders are allowed 120mm mid-point of the armrest to the extension tip.
CATEGORY 3 – riders are allowed 140mm mid-point of the armrest to the extension tip.
NON-CATEGORY – riders are allowed 100mm mid-point of the armrest to the extension tip.

Please note that mid-point to extension tip measurements are measured vertically. All accessories are included in these dimensions.

COMPLIANT
CONDITIONS APPLY
NON-COMPLIANT

UC I NON – CATEGORY

R iser Anqle| Handgrip
Ergo| E r go (Track)| Standard Pole| Standard Pole (Long)
10| 79| 79| 74| 94
15| 100| 100| 98| 119
20| 120| 120| 120| 143
25| 139| 139| 142| 166
30| 158| 158| 162| 188
UCI CATEGORY 2

Riser Anqle| Handgrip
Ergo| Ergo (Track)| Standard Pole| Standard Pole (Long)
10| 79| 79| 74| 94
lS| 100| 100| 98| 119
20| 120| 120| 120| 143
25| 139| 139| 142| 166
30| 158| 158| 16 2| 188
UCI CATEGORY 1

Riser Angle| Handgrip
Ergo| Ergo (Track)| Standard Pole| Standard Pole (Long)
10| 79| 79| 74| 94
lS| 100| 100| 98| 119
20| 120| 120| 120| 143
2S| 139| 139| 14 2| 166
30| 158| 158| 162| 188
UCI CATEGORY 3

R iser Anq le| Handgrip
E rgo| Ergo (Track)| Standard Pole| Standa r d Pole (Long)
10| 79| 79| 74| 94
l S| 100| 100| 98| 119
20| 120| 120| 1 20| 143
25| 139| 139| 142| 166
30| 158| 158| 162| 188

STANDARD BUILD

IMPORTANT – The fixed angled risers and baseball-specific risers are not compatible with the standard build option.

REACH: All reach dimensions are measured from the rear riser bolt hole horizontally to the extension tip.

Adjustable Riser	Reach Window
SP	SP (Long)
Min	Max
10	289
15	280
20	271
25	259
30	246

WIDTH
All width dimensions are measured from outside to outside at the rear of each armrest.

Adjustable Riser	Armrest Width (lateral c-c +/-)
Min	Max
10	+65
15	+65
20	+65
25	+65
30	+65
EXAMPLE	Armrest Width
---	---
(lateral c- c)	Min
105	170
110	175
115	180
120	185
125	190
130	195
135	200
140	205

For armrest widths narrower than 200mm the inner edge will require trimming.

ANEMOI BASEBAR BUILD

IMPORTANT – Mount plates are not compatible with the Anemoi baseball build option.

REACH: All reach dimensions are measured from the rear riser bolt hole horizontally to the extension tip.

Adjustable Riser	Reach Window
SP	SP (Long)
Min	Max
10	289
15	280
20	271
25	259
30	246
Fixed Riser	Reach
---	---
SP	SP/L
10	306
15	296
20	286
25	273
30	258

WIDTH
All width dimensions are measured from outside to outside at the rear of each armrest.

Adjustable or Fixed	Armrest Width
Riser	Min
10	170
15	170
20	170
25	170
30	170

For armrest widths narrower than 200mm the inner edge will require trimming.

CONVERSION KIT BUILD

REACH
All reach dimensions are measured from the rear riser bolt hole horizontally to the extension tip.

Adjustable Riser	Reach Window
SP	SP (Long)
Min	Max
10	289
15	280
20	271
25	259
30	246
Fixed Riser	Reach
---	---
SP	SP/L
10	306
15	296
20	286
25	273
30	258

WIDTH
All width dimensions are measured from outside to outside at the rear of each armrest.

Adjustable or Fixed	Armrest Width
Riser	Min
10	170
15	170
20	170
25	170
30	170

For armrest widths narrower than 200mm the inner edge will require trimming. All dimensions are in millimetres (mm) unless otherwise stated.

MOUNT PLATE BUILD

IMPORTANT – The mount plate build option is only compatible with flat-top riser stacks. NB – the reach tables show dimensions based on a 25mm bolt centre. Different bolt centres will change the reach window.

REACH: All reach dimensions are measured from the rear riser bolt hole horizontally to the extension tip.

2Smmc-c	Reach Window – Long Plate (Reverse)
Adjustable Riser	SP
Min	Ma,
10	234
15	225
20	216
25	204
30	191
2Smmc-c	Reach Window – Short Plate (Reverse)

Adjustable

Riser

| SP| SP(Long)| Ergo
Min| Ma,| Min| Ma,| Min| Ma,
10| 254| 322| 274| 343| 259| 327
15| 245| 313| 263| 332| 248| 316
20| 236| 301| 252| 318| 237| 303
25| 224| 287| 238| 301| 224| 287
30| 211| 271| 223| 283| 209| 269
2Smmc-c| Reach Window – Short Plate
Adjustable

Riser

| SP| SP(Long)| Ergo
Min| Ma,| Min| Ma<| Min| Ma<
10| 274| 342| 294| 363| 279| 347
15| 265| m| 283| 352| 268| 336
20| 256| 321| m| 338| 257| m
25| 244| 307| 258| 321| 244| 307
30| 231| 291| 243| 303| 229| 289
2Smmc-c| Reach Window • Long Plate
Adjustable Riser| SP| SP(Long)| Ergo
Min| Ma<| Min| Ma,| Min| Ma<
10| 294| 362| 314| 383| 299| 367
15| 285| 353| 303| 372| 288| 356
20| 276| 341| 292| 358| 277| 343
25| 264| 327| 278| 341| 264| 327
30| 251| 311| 263| m| 249| 309

WIDTH: All width dimensions are measured from outside to outside at the rear of each armrest.

Adjustable	Armrest Width (lateral c-c +/-)

orFixed

Riser

| Inboard| Outboard
Min| Max| Min| Max
10| +30| +100| +100| +170
15| +30| +100| +100| +170
20| +30| +100| +100| +170
25| +30| +100| +100| +170
30| +30| +100| +100| +170
EXAMPLE| Armrest Width
---|---
Inboard| Outboard
(lateral c-c)| Min| Ma x| Min| Ma x
105| 135| 205| 205| 275
110| 140| 210| 210| 280
115| 145| 215| 215| 285
120| 150| 220| 220| 290
125| 155| 225| 225| 295
130| 160| 230| 230| 300
135| 165| 235| 235| 305
140| 170| 240| 240| 310

For armrest widths narrower than 200mm the inner edge will require trimming. All dimensions are in millimetres (mm) unless otherwise stated.

RISER SELECTION

ADJUSTABLE RISER
- The adjustable riser is available in two different options. Which option you receive will depend on your build selection.
UNIVERSAL ADJUSTABLE RISER
- You will receive this riser with the Standard build option only. The universal risers are slotted on the underside. With the use of our barrel nuts, these risers can be installed onto a variety of flat-top riser stacks that have bolt centers between 15-40mm.
BASEBALL SPECIFIC ADJUSTABLE RISER
- You will receive this option if you have selected the Anemoi Basebar, Conversion Kit or Mount Plate build.
- These risers have threaded bosses on the underside which provides easier installation and seamless integration with WattShop componentry.

FIXED ANGLED RISER

Designed to provide you with a clean and seamless integration between riser and extension, the fixed-angled riser is available in five different angles, each of which comes with 2 degrees of toe-in. This may be the preferred option for riders who know their optimal extension angle or want to maximise their position within the UCI regulations.

10 DEGREES
15 DEGREES
20 DEGREES
25 DEGREES
30 DEGREES

These risers are only compatible with the Anemoi Basebar, Conversion Kit or Mount Plate builds.

ARMREST + COMPUTER MOUNT SELECTION

ARMRESTS
- Available in two different styles. Both are slotted to provide width adjustment.
DUAL-SIDED
- Each armrest has a high-sided inside and outside supporting faces, giving the armrest a “U” shape. We recommend this style of armrests for widths 220mm or wider this ensures you will benefit from the support of the inside edge.
SINGLE SIDED
- Each armrest has a high-sided outside supporting face. We recommend this for armrest widths less than 220mm. At less than 220mm your forearms are likely touching so the benefit of the inside supporting face is reduced.

COMPUTER MOUNT

Available in two different options; Garmin and Wahoo and in two different extension interface options.

SINGLE MOUNT

This option will come supplied as standard with the Standard and Mount Plate built options. It attaches to the left-hand extension only, hence a single mount. 5mm spacers can be used to move the computer mount further away from the extension if needed.
You also can adjust your toe.

CROSSBRACE MOUNT

Comes supplied as standard with all Anemoi Basebar or Conversion Kit builds.
This computer mount attaches to both extensions to centralise and provide additional strength.
GoPro-style accessories are available for both GoPro and front-light attachments.

CONVERSION SPACER SELECTION

CONVERSION SPACER
- Designed to accommodate various basebars and riser stacks, our spacers are precision-matched to stock riser profiles for a visually cohesive integration of our Anemoi component range.
INTEGRATION
- Profile-matched to your existing riser stacks, ensuring seamless integration between your base bar and the Anemoi product range.
OPTIMAL LATERAL STACK CENTRES
- Bring uniformity to your riser stack lateral centres. Converting your existing riser stack lateral centres to 105mm. This alignment ensures your extension poles are centred on your forearm.
- Our range of Conversion Spacers is continually expanding however if you don’t see your model of baseball in the list please get in contact.
- TREK SPEED CONCEPT – TOP AND UNDERSIDE VIEW