Laserliner 082-031 ClimaData Box Instructions
- June 5, 2024
- Laserliner
Table of Contents
- Laserliner 082-031 ClimaData Box ClimaData Box
- Function / Application
- General safety instructions
- Information on maintenance and care
- User interface
- Notes on the measurement process and on use
- Measurement analysis
- LO- error message
- Technical Data
- EU directives and disposal
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Laserliner 082-031 ClimaData Box ClimaData Box
Completely read through the operating instructions, the „Warranty and Additional Information“ booklet as well as the latest information under the internet link at the end of these instructions. Follow the instructions they contain. This document must be kept in a safe place and passed on together with the device.
Function / Application
This device measures long-term ambient temperature, air humidity and dew point. Measurements are stored internally and can be accessed by connecting the device to a PC via USB. Using the supplied software on a PC, the measurement parameters can be configured, a new measurement prepared, and the data subsequently analysed.
General safety instructions
- The device must only be used in accordance with its intended purpose and within the scope of the specifications.
- The structure of the device must not be modified in any way.
- Do not expose the device to mechanical stress, extreme temperatures or significant vibration.
Safety instructions
Dealing with electromagnetic radiation
- The measuring device complies with electromagnetic compatibility regulations and limit values in accordance with EMC-Directive 2014/30/EU.
- Local operating restrictions – for example, in hospitals, aircraft, petrol stations or in the vicinity of people with pacemakers – may apply. Electronic devices can potentially cause hazards or interference or be subject to hazards or interference.
Information on maintenance and care
Clean all components with a damp cloth and do not use cleaning agents, scouring agents and solvents. Store the device in a clean and dry place.
- The display toggles between temperature, relative humidity and dew point/start and stop measuring
- Alarm function
- Measurement active
- Battery compartment (rear)
- Display of current, min. and max. measurements in selected mode Sensor
- USB interfac
- Time display active
- Date display active
- Time / date display
- Data memory full
- Display of temperature, relative humidity, dew point
- Measurement in °C / °F
- Display of measured value
- Measurement active
- Display of MIN values
- Display of MAX values
- Battery indicator
Example: Display of MIN temperature
Display toggles between time and date every 10 seconds.
Inserting battery
Open the battery compartment and insert battery according to the symbols. Be sure to pay attention to polarity.
USB drivers / Software installation / Commissioning
Load the CD in the drive and follow the installation Close the installation
program once installation has been successfully completed.
You must install the USB drivers before you can start the application and
connect the device to a computer. To do this, insert the supplied CD into the
drive and open the folder entitled “USB Driver”. Depending on your Windows
operating system version, start the following installer:
- 32bit version: CP210xVCPInstaller_x32
- 64bit version: CP210xVCPInstaller_x64
Check the basic information relating to your Windows installation to see which
type of system you have. Follow the installation instructions.
Then connect one end of the supplied USB cable to the mini-USB port of the
device and the other end to a free USB port on your computer, and start the
application. The software is only available in English.
User interface
Set date /
time
Setup menu
Measurement-specific settings on the connected device can be defined in the
Setup menu.
New configuration automatically deletes all existing data.
Sampling rate
The sampling rate defines how often measurements are recorded. Setting options: 1 … 60 seconds, 1 … 60 minutes and 1 … 24 hours. The maximum measurement duration is calculated under “Recording time”. The measurement memory is full at the end of this time. See also section 5.6 “Continuous /non- continuous recording”.
LED cycle setting
The active recording is signaled by the LED (3) and “REC” on the display. The LED signal can be set to appear every 10, 20 or 30 seconds. Or the LED signal can be switched off.
Options when starting to measure
Measurement can be started manually, automatically, or after the set time.
- Manually; Hold the key (1) down to start or stop measurement.
- Automatically:; Measurement starts as soon as the device is disconnected from the computer.
- Time lag on start:; Measurement commences at the end of the set time.
Current time
“Current time” displays the set date and time. You can change the date format in this menu.
Alarm function settings
The alarm range can be freely defined for the three measurement variables:
Temperature, relative humidity and dew point. If the measured value goes above
or below the set cap or floor, the alarm LED (2) flashes once a minute.
LED red: Max./min. temperature exceeded LED yellow: Max./min. humidity
exceeded
LED flashes when alarm signals low/high: The alarm function can be
switched on or off.
Alarm when recording is not active: A signal is issued when the recording
function (REC) is not active.
Continuous / Non-continuous recording
- Continuous recording: The device records until manually stopped.
- Non-continuous recording: Older measurements are overwritten. Recording stops automatically when the data memory is full.
Notes on the measurement process and on use
- Connect ClimaData Box to the PC
- Download and backup any existing data. Starting or configuring a new measurement deletes all existing data.
- Configure the recording function in the Setup menu and save your settings
- Depending on your start parameter, position the device at the measuring point and record measurements. If set to manual start, hold key 1 down. The display shows “Rec” to indicate that the measurement recording is active.
- To stop recording, either hold key 1 down again, or recording stops when the memory is full, depending on the set parameter.
- Connect ClimaData Box to the PC, download and backup data.
If the device has been placed in a cold and/or very humid environment, condensation may form in the sensor housing when it is removed due to the change in climate. Position the device upright for a while to allow it to acclimatise.
Measurement analysis
The recorded measurements are displayed in a bar chart.
The
measurements can also be shown as a list.
Zoom
You can zoom in and out of partial areas by holding down the left mouse
button, drawing a box over the required area, and then releasing the button.
Use the horizontal scroll bar to display further measurements. The left-hand
vertical scroll bar changes the view of the temperature data and the right-
hand bar of the relative humidity.
Zoom out Back to normal view
Toggle unit (°C/°F)
Unit (°C/°F) Measurements are displayed in °C or °F.
Setup Y axis
Y axis You can change the scale on the Y axis.
Colour settings Display
LO- error message
-LO- in the display indicates a problem with the sensor. The device requires servicing. Please contact the Service department at UMAREX-LASER LINER.
Technical Data
(Subject to technical changes without notice. Rev18W48)
Technical Data
(Subject to technical changes without notice. Rev18W48)
Distance measurement
Precision (typical)*| ± 2 mm
Inside measurement range| 0,1 m – 50 m
Angle measurement**
Measuring range| ± 90°
Resolution| 0,1°
Precision| 0,1°
Laser class| 2 < 1 mW
Laser wavelength| 650 nm
Operating conditions
| -10°C … 40°C, max. humidity 80% rH, no condensation, max. working altitude
2000 m above sea level
Storage conditions| -20°C … 70°C, max. humidity 80% rH
Radio module operating data
| Bluetooth LE 4.x interface; Frequency band: ISM band 2400–2483.5 MHz, 40 channels; Transmission power: max. 10 mW; Bandwidth: 2 MHz;
Bit rate: 1 Mbit/s; Modulation: GFSK/FHSS
Automatic switch-off| 30-sec laser / 10 min device
Power supply| 2 x AAA 1.5 Volt batteries
Technische Daten (Subject to technical changes without notice)
Dimensions (W x H x D)| 43 x 110 x 27 mm
Weight (incl. batteries)| 100 g
- measuring distance up to 10 m with strongly reflective target surface and at room temperature. The measurement deviation may increase by ± 0.2 mm/m for greater distances and under unfavourable measuring conditions such as strong sunlight or weakly reflective target surfaces.
** at max. 5000 lux
EU directives and disposal
This device complies with all necessary standards for the free movement of
goods within the EU.
This product is an electric device and must be collected separately for
disposal according to the European Directive on waste electrical and
electronic equipment.
Further safety and supplementary notices at:
http://laserliner.com/info?an=ACH
SERVICE
Umarex GmbH & Co KG
– Laserliner –
Möhnestraße 149, 59755 Arnsberg, Germany Tel.: +49 2932 638-300, Fax: +49 2932
638-333 info@laserliner.com
Umarex GmbH & Co KG Donnerfeld 2 59757 Arnsberg, Germany
Tel.: +49 2932 638-300, Fax: -333
www.laserliner.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>