YITAHOME SHMYD-V1 Level 2 EV Charger Instruction Manual
- June 15, 2024
- YITAHOME
Table of Contents
YITAHOME SHMYD-V1 Level 2 EV Charger
USE&CARE INSTRUCTIONS
Note: This adapter is not compatible with CCS1& Mennekes Type 1 plug
.
Technical parameters
ASSEMBLY INSTRUCTIONS
Easy Setup Installation
- Step 1: Securely push the adapter into the charging port.
- Step 2: Connect your J1772 Plug to the adapter until you hear a “click”.
- Step 3: Wait until the indicator turns green.
Specification
Item
| Level 2 Portable EV Charger
---|---
Rate Current| A.6A/8A/10A/13A/16A
B.10A/16A/20A/24A/32A
C.16A/20A/24A/32A/40A
Input Voltage AC| 110V~240V
Rate Frequency Waterproof Degree| 50Hz/60Hz
| IP67
Working Temperature| -25℃~+55℃
Withstand Voltage| 2000V
Shell Material| PC
Terminal Material| Copper Alloy Silver Plating
Flame Retardant Grade| UL94 V-0
Operating Humidity| 20%-85%
Mechanical Life| No-Load Plug In / Pull Out ＞10000 Times
Pressure Impact Force| Can afford 1m drop and 2t vehicle run over
pressure Impact Force
25FT
Cable Length|
Standard| IEC 62752 , IEC 61851
Certificatevv| TUV,CE,UKCA,FCC
Operating Instruction
How to start charging
- Step 1. Take out the charger and firmly insert the power plug into the wallend outlet socket.
- Step 2. Please press the button of “CURRENT ” to adjust your required current. Or please press the button of ” DELAY ” to adjust your charging time. The device will default to the last current setting when we charge next time.
- Step 3. Insert the charging plug (Car End) into the car side charging inlet, the device start charging automatically while the READY/CHARGE, POWER indicators are all green.
How to stop charging
- Step 1. Please take out the EV charging gun from car side after the car charging is complete.
- Step 2. Disconnect the power plug from the wall socket outlet.
- Step 3. Pack up the EV charger cable and put into the bag.
Security Protection
- Short Circuit Protection
- Over and Under Frequency Protection
- Over Current Protection
- Leakage Current Protection (restart recover)
- Over Temperature Protection
- Overload Protection (self-checking recovery)
- Ground Protection
- Surge Protection
- Over Voltage and Under-voltage Protection
GOOD TO KNOW
- This is a Level 2 EV charging cable don’t use it for EV’s other different inle types.
- Please check if the device is intact and items are in accordance with the packing list when you receive the package.
- Do not submerge the EV control box or EV charging connector in water.
- Do not use the charger if the EV controller box is damaged.
- Don’t charge if the wall socket is damaged, rusted, cracked or loosely connected.
- Wipe with a clean and dry cloth if the plug gets dirty or wet.
- The device must be grounded.
- Do not use this device with an extension cord or an adapter.
- Do not place the charging cable near a high-temperature object when it is working.
- Do not use this device with an extension cord or an adapter, Please do not disconnect the plugs while the EV charger is charging the vehicle.
CONTACT US
If you have any questions about the installation of YITAHOME products, just contact us at +1 888-717-8084 from Mon- Fri 8:00 AM-4:30 PM PST / Sat. 8:00 AM-12:00 PM PST or e-mail us at after- sale.cs@hotmail.com
An alternative method to contact us (amazon.com orders only)
- Log into your Amazon account
- Go to “Your Orders” and find the purchase
- Click on “Contact Seller”