SFA SANIBROY TRAYMATIC Extern Instructions
- June 5, 2024
- SFA
Table of Contents
TRAYMATIC Ext.
INSTALLATION INSTRUCTIONS
154 – 3 EXT
01 – 15
SANIBROY TRAUMATIC Extern
DESCRIPTION
This pump is (manufactured in a factory that is quality) certified to ISO
9001, and ISO 14001. Installed and used correctly, the unit will give
consistent and reliable service.
This device is not designed for persons (including children) with limited
physical, sensory or mental abilities, or those with minimal experience and
knowledge, unless they are monitored and are given the necessary instructions
for using the device, with the help of a person responsible for their safety.
Monitor children and make sure they do not play with the device.
APPLICATIONS
This device is a pump designed to evacuate waste water from private dwellings
(except for water coming from WCs). SANIVITE ®, SANISPEED ®, and SANIPUMP 2 ®
are designed to handle the waste evacuation from a bath, kitchen sink,
dishwasher, and washing machine. Its powerful pump will deal with everyday
normal usage. SANISHOWER® FLAT/ SANIDOUCHE® FLAT is designed to handle the
waste from a shower and handbasin. Sanispeed will take the above at a heavier
duty rate of usage.
SANISHOWER ® /SANIPUMP 1 ® is designed to take the waste from a shower and
handbasin.
This appliance conforms to EN 12050-2 and the European standards concerning
electrical safety and electromagnetic compatibility.
INSTALLATION
The unit should be installed in the same space as the connected facilities and
should be accessible for possible service. The fitting and working of your
appliance must meet local regulations and the EN 12056-4 standard.
To optimize the latest technical developments concerning soundproofing
incorporated into this unit, it is important to:
- fix the discharge pipe correctly, with distances of not more than one meter between the fastenings.
CONNECTION TO THE ELECTRICAL SUPPLY
The electrical installation should be carried out by a quality- field
person.
The unit should be connected to a fully earthed electrical supply. All wiring
must conform to BS7671, 1992 requirements for electrical installations. The
unit requires a 20/240V single phase AC 50 Hz supply (UK specification). Do
not connect the unit to a conventional plug and socket.
It must be wired into a fused, unswitched, fixed wiring connector fitted
with a 5 amp fuse.
The wires in the mains lead are colored in accordance with the following code:
Brown Live Blue – Neutral Green/Yellow – Earth
Warning: Ensure the electricity is turned OFF at the main switchboard
before wiring to the connector. All work on cable, pressure chamber, and motor
should only be carried out by a qualified Saniflo servicing agent, as special
tools are required.
COMMISSIONING THE UNIT
Once electrical and plumbing connections have been made, check that all seals and connections are watertight. Check both the discharge pipework from the unit and the other sanitary appliance connections.
MAINTENANCE
WARNING !!!
If away for a long period, we recommend that you turn off the water supply to
the WC served by the unit.
CARE OF YOUR UNIT
In order to remove the scale and clean the pump, use a household descent (like
SANIFLO Cleanser/descent).
FAULT FINDING / REMEDIES
IN ALL CASES, YOU MUST DISCONNECT THE PUMP FROM THE POWER SUPPLY
SYMPTOMS | PROBABLE CAUSES | REMEDIES |
---|---|---|
• The motor does not activate | • The electrical power supply is not active |
• The electrical power supply is defective
• The motor or the control system is defective| • Restore the electrical
supply
• Check the electrical power supply
• Otherwise, ask an approved repair agent to intervene
• The motor intermittently activates| • The connected sanitary devices are
leaking
• The non-return valve is faulty| • Check the installation upstream
• The motor operates normally but does not stop or continue to run for a long
time| • The length or height of the installation is over the specification or
there are too many bends/elbows
• The pump cover plate is occluded| • Clean or replace the non-return valve
• Check the installation
• Otherwise, ask an approved repair agent to intervene
• The unit stop| • The unit has been running for too long (thermal cut-out)| •
Wait for reset, then ask an approved repair agent to intervene
• Soiled water comes up into the shower basin (units with side inlets)| •
Shower installed too low as compared with the pump
• Hinged side inlet discs clogged up| • Check the installation
• Clean the hinged discs
• Otherwise, ask an approved repair agent to intervene
GUARANTEE
2 years guarantee from its date of purchase subject to correct installation
and correct use.
Warning : Do not dispose of solvents, paints (do not wash paint brushes
in the sink), caustic, acid, or other chemicals in these products.
SANIFLO Ltd.,
Howard House, The Runway
South Ruislip Middx.,
HA4 6SE
Tel. +44 208 842 0033/4040
Fax +44 208 842 1671 08457 650011 (Call from a landline)
020 8842 1671
Documents / Resources
| SFA
SANIBROY TRAYMATIC
Extern
[pdf] Instructions
SANIBROY TRAYMATIC Extern, TRAYMATIC Extern
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>