Laserliner 082034 ClimaPilot Digital Hygrometer Device Instruction Manual
- June 5, 2024
- Laserliner
Table of Contents
Laserliner 082034 ClimaPilot Digital Hygrometer Device
Completely read through the operating instructions, the „Warranty and Additional Information“ booklet as well as the latest information under the internet link at the end of these instructions. Follow the instructions they contain. This document must be kept in a safe place and passed on together with the device.
Function / Application
The device is used to measure relative humidity and ambient temperature and to display the calculated dew point. Humidity and temperatures are measured by means of high-speed sensors integrated in the tip of the probe. Thanks to its low power con- sumption, the device can also be used for long-term measurements. The integrated min/max function allows the lowest and highest measured values to be shown.
General safety instructions
- The device must only be used in accordance with its intended purpose and within the scope of the specifications.
- The structure of the device must not be modified in any way.
- Do not expose the device to mechanical stress, extreme temperatures or significant vibration
Safety instructions
Dealing with electromagnetic radiation
-
The measuring device complies with electromagnetic compatibility regulations and limit values in accordance with EMC-Directive 2014/30/EU.
-
Local operating restrictions – for example, in hospitals, aircraft, petrol stations or in the vicinity of people with pacemakers – may apply. Electronic devices can potentially cause hazards or interference or be subject to hazards or interference.
-
Sensor
-
LC display
-
Toggle measurement in °C / °F
Toggle temperature / dew point display -
Switch on MAX/MIN values
-
On/off button (rear)
-
Battery compartment (rear)
-
features
- Display of MAX values
- Display of MIN values
- Measurement in °F
- Measurement in °C
- Relative humidity in %rH
- Room temperature/dew point display
Inserting battery
Open the battery compartment and insert battery according to the symbols.
Be sure to pay attention to polarity.
ON / OFF
To turn on, set the switch (5) to ON. The device displays the ambient
temperature and relative humidity.
- When switching to a measuring location with significantly different temperature and humidity levels, allow the device time to adapt!
- For measurements outside of the measuring range, the device displays „HI“ or „LO“.
Dew point display
By briefly pressing the „MODE“ button, the measured dew point is displayed.
MAX / MIN
To determine the maximum or minimum measured values during a measurement,
press and hold the „MAX / MIN“ button until either „MAX“ or „MIN“ appear on
the display. The normal measuring mode is set when no function flashes on the
display.
- Switching off the device deletes the min/max values.
5 °C / °F
To set the desired temperature unit, press and hold the „MODE“ button for 2
seconds until the corresponding symbol appears on the display.
Information on maintenance and care
Clean all components with a damp cloth and do not use cleaning agents,
scouring agents and solvents. Store the device in a clean and dry place.
Technical data
Technical data
Humidity (relative) Measuring range Accuracy (absolute)|
20% … 90%
± 5% rH (25% rH … 85%rH)
Ambient temperature Measuring range Accuracy|
-10°C … 50°C 1°C
Dew point temperature Measuring range Accuracy|
-28,6°C … 47,9°C
± 2 °C
Power supply| 1 x 1,5V LR44 (AG13)
Operating conditions| -10°C … 50°C, max. humidity 99% rH, no condensation,
max. working altitude 2000 m above sea level
Storage conditions| -10°C … 60°C, max. humidity. 85% rH
Dimensions (W x H x D)| 138 x 27 x 19 mm
Weight| 38 g (incl. battery)
EU directives and disposal
This device complies with all necessary standards for the free movement of
goods within the EU.
This product is an electric device and must be collected separately for
disposal according to the European Directive on waste electrical and
electronic equipment.
Further safety and supplementary notices at:
http://laserliner.com/info?an=ABD