solis S2-WL WL Stick Datalogger Installation Guide

: June 5, 2024
: solis

Table of Contents

Install
LAN configuration
Soliscloud APP
Create Plant
FCC Certification
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WL Stick Datalogger Quick Installation Manual
Version: 1.0

Delivery Content

1 WL stick
1 Quick Installation Manual

Install

Install the network cable
Setpl: Remove the “Plastic Nut”, “Thread Clamp Claw”, and “Sealing Ring” in turn.
Setp2: Pass the network cable plug through the “Plastic Nut”, “Thread Clamp Claw”, and “Sealing Ring” (with opening) in the direction as shown in the figure below.

Setp3: Fully embed the “Sealing Ring° into the “Thread Clamp Claw”.
Setp4: Connect the “RJ45 Plug” to the datalogger and tighten the “Plastic Nut”.
NOTE Due to limited space, only the RJ45 plug without a protective shell can be used.

Install the datalogger
Connect the data logger to the corresponding 4-pin COM port of the inverter. A Solis 5K inverter is used here as an example. Please follow the instructions below:

Install the datalogger:

Insert the datalogger to the inverter COM port.
Rotate the black circle clockwise.

NOTE Only rotate the black circle, not the sliver cover.
If you need to collect data from multiple inverters, please follow the inverter user manual to establish a communication connection with the inverter using the RS485 communication cable in a “daisy chain” manner.
After the data logger is installed on the inverter, if the inverter is powered on, you need to set the inverter slave address, the first inverter is “01”, and the second inverter is “02”, And so on.

NOTE

The device must be installed away from the strong magnetic field produced by large electrical appliances such as microwave ovens, refrigerators, telephones, metal walls, etc. Otherwise, the communication quality may be affected. It may also be affected by lighting storms.
The [RESET] button on the back is used for a connection.
• Short press will send the data immediately.
• Long press for 5 seconds will enter into config mode for connection router. -Long press for 10 seconds will reset the connection. The three constantly ON LED lights indicate the datalogger is working normally.

LED Lights Status

LED indicators	Description	LED Status	Meanings

NOTES WL Stick automatically obtains IP by default. If the network cable supports automatically obtains IP, please jump to ” 3″ for APP registration. If the network cable does not support obtaining IP automatically, please continue to follow “2 ” for IP settings.

LAN configuration

Step 1: Enter 10.10.100.254 in the web browser, and open the following configuration interface. Enter Username Admin and Password 123456789.

Step 2: Select the °WAN port setting” and °Static IP”. Enter IP address, Subnet mask, Gateway address, and DNS server address for network cable. Then click the “Save°.

Step 3: The following interface pops up to indicate that the setting is successful. Otherwise please try LAN configuration again.

Soliscloud APP

Step 1: Use your phone to scan the QR code to download and register the Solis Cloud APP. Or directly download from APP Store or Google Play Store by searching “Solis Cloud”.

Step 2: Click the °Register”.

Step3: Select Owner or Organization for email address registration.
Step4: Enter the email to get the verification code, then enter your account and password, and last click the “Register”.

Create Plant

Step: Enter the main page of the Solis Cloud APP, click “+” at the top right corner, and select “Add plant”.

Step 2: Input the information about the plant as required. Then click “Done”.

Step 3: Confirm the plant information. Click “Create plant”.

Step 4: Click “View plant” to enter the plant homepage then add the datalogger.
Step 5: Scan the SN number of the datalogger or manually input it.

Note: Scan the datalogger SN, NOT the inverter SN.
Step 6: Plant creation succeeds. Click “Continue…data logger* to check the monitoring data. If the plant has multiple data loggers, please click “View Plant’.

FCC Certification

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful Interference. and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC warning:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to protect reasonably against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
Contact
Please contact us if you have any technical problems in terms of the product. Please provide the following information as well:

Inverter SN
Datalogger SN
Problem Description Ginlong Technologies Co., Ltd.
No. 57 Jintong Road, Binhai Industrial Park, Xiangshan, Ningbo, Zhejiang, 315712, P.R.China.
Tel: +86 (0)574 6578 1806
Fax: +86 (0)574 6578 1606
Email: info@ginlong.com
Web : www.ginlong.com