PAX E600Mini Integrated Smart Terminal Instruction Manual
- June 5, 2024
- Pax
Table of Contents
PAX E600Mini Integrated Smart Terminal
Contents Checklist
Please check the components after unpacking. If any one of them is missing, or if there is a page missing from the product manual,etc., please contact the dealer.
| Name | Qty. |
|---|---|
| E600Mini | 1 |
| AC Power Adapter | 1 |
| AC Power Cable | 1 |
| Product Manual | 1 |
Product Description
Installation
- Power on: Press and hold the Power button for three seconds until the main screen displays normally.
- Power off: Press and hold the Power button for three seconds until the shutdown menu appears, tap “Shutdown”, and then “shutting…” appears. The terminal will be turned off after a few seconds.
- Swipe the magnetic stripe card: Place the magnetic stripe face down (keep the magnetic stripe card perpendicular to the main display), swipe card through the magnetic card slot at a constant speed.
- IC Card: Place the IC chip face down, then insert the IC card into the card slot, and push it to the end.
- Contactless card: Put the contactless card on the center of the payment module screen.
- Tear paper : Press the print paper downward along the cutter and tear it leftward or rightward when getting close to the main display.
Charge: Insert the external adapter or the base to charge the device, the indicator lighting in red means the device is charging; the indicator lighting in green means charging is completed; the indicator flashing in red and green alternately means charging is abnormal.
Insert SIM/ microSD card: Take the Card Pick-up needle out of the box，insert the Card Pick-up needle into the SIM/mircoSD card slot.
Specification
-
Operating System: Android 10.0
CPU: -
Memory:
-
Display:
-
Printer:
-
Audio:
-
Camera:
L-Sensor (Ambient Light Sensor): Automatically adjust the backlight brightness
of the main display
Wireless Communication: Support Wi-Fi® , Bluetooth® wireless technology,
3G/4G Positioning: Support GPS, Compass, Gingileo, GLONASS
Card Slots: SIM card slot microSD card slot（maximum supports 128GB）
magnetic stripe card/IC card slot, using two-in-one（support MAG&ICC） Magnetic
Card Reader: Support track 1/2/3.
IC Card Reader: Conform to the standard of ISO7816, EMV2000 L1&L2,
PBOC3.0 Contactless Card Reader: Compatible with ISO14443 Type A&B
Working Environment Temperature: 0℃～50℃(32℉～122℉) R.H.
Storage Environment: 10%～93% (non-condense)
Temperature: -20℃～70℃(-4℉～158℉) R.H.:5％～95％ (non-condense)
Cautions of installation and usage
- Avoid exposing the terminal in hot, humid, dusty or strong electromagnetic environment.
- Do not violently vibrate, shake or beat the product.
- Do not plug/unplug any units of the product when it is power on, otherwise it may damage the internal circuit.
- Do not maintain the terminal if you are non-professional
- Before inserting the magnetic stripe/IC/contactless card, please check whether there is any foreign object inside or surround the card slot , and if any , report to related personnel.
Caution
Risk of explosion if battery replaced by an incorrect type. Dispose of used
batteries according to the instructions.
Hereby, PAX Computer Technology (Shenzhen) Co., Ltd. declares that the radio
equipment type E600Mini is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address：https://www.pax.com.cn/ProductCE/index.aspx
Icon shows
RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization
or to the retailer when he buys an new electrical or electronic equipment.
The symbol indicates DC voltage
microSD logo
Trademark notice:
“microSD logo is a trademark of SD-3C LLC.”
“The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by PAX Technology Limited is
under license. Other trademarks and trade names are those of their respective
owners.”
PAX TECHNOLOGY LIMITED reserves the right to change product technology
specifications without notifying.
PAX TECHNOLOGY LIMITED
Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd.
Address : 4/F, No.3 Building, Software Park, Second Central Science-Tech
Road, High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C.
Tel: 0755-86169630 Fax: 0755-86169634
Website: http://www.pax.com.cn
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
SAR Information Statement
Your wireless Countertop Payment Terminal is a radio transmitter and receiver.
It is designed and manufactured not to exceed the emission limits for exposure
to radiofrequency (RF) energy set by the Federal Communications Commission of
the U.S. Government. These limits are part of comprehensive guidelines and
establish permitted levels of RF energy for the general population. The
guidelines are based on standards that were developed by independent
scientific organizations through periodic and thorough evaluation of
scientific studies. The standards include a substantial safety margin designed
to assure the safety of all persons, regardless of age and health. The
exposure standard for wireless mobile Countertop Payment Terminals employs a
unit of measurement known as the Specific Absorption Rate, or SAR. The SAR
limit set by the FCC is 1.6 W/kg. * Tests for SAR are conducted with the
Countertop Payment Terminal transmitting at its highest certified power level
in all tested frequency bands. Although the SAR is determined at the highest
certified power level, the actual SAR level of the Countertop Payment Terminal
while operating can be well below the maximum value. This is because the
Countertop Payment Terminal is designed to operate at multiple power levels so
as to use only the power required to reach the network. In general, the closer
you are to a wireless base station antenna, the lower the power output. Before
a Countertop Payment Terminal model is available for sale to the public, it
must be tested and certified to the FCC that it does not exceed the limit
established by the government adopted requirement for safe exposure. The tests
are performed in positions and locations (e.g., at the ear and worn on the
body) as required by the FCC for each model. The highest SAR value for this
model Countertop Payment Terminal when tested for use on the body, as
described in this user guide, is 2.717W/Kg(Body-worn measurements differ among
Countertop Payment Terminal models, depending upon available accessories and
FCC requirements). While there may be differences between the SAR levels of
various Countertop Payment Terminals and at various positions, they all meet
the government requirement for safe exposure.
The FCC has granted an Equipment Authorization for this model Countertop
Payment Terminal with all reported SAR levels evaluated as in compliance with
the FCC RFexposure guidelines. SAR information on this model Countertop
Payment Terminal is on file with the FCC and can be found under the Display
Grant section of http://www.fcc.gov/ oet/fccid after searching on
FCC ID: V5PE600MINI Additional information on Specific Absorption Rates (SAR)
can be found on the Cellular Telecommunications Industry Asso-ciation (CTIA)
web-site at http://www.wow-com.com. * In the United States and Canada, the SAR
limit for mobile Countertop Payment Terminals used by the public is 1.6
watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a
sub-stantial margin of safety to give additional protection for the public and
to account for any variations in measurements.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance
of 0mm must be maintained between the user’s body and the handset, including
the antenna. Third-party belt-clips, holsters,
and similar accessories used by this device should not contain any metallic
components. Body-worn accessories that do not meet these requirements may not
comply with RF exposure requirements and should be avoided. Use only the
supplied or an approved antenna.
IC STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s)
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. End user must follow the specific operating
instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. These requirements set a
SAR limit of 1.6 W/kg averaged over one gram of tissue.
The highest SAR value for this model when worn on the body is 0.23W/Kg. This
device was tested for typical body-worn operations. To comply with RF
exposurerequirements, a minimum separation distance of 0mm must be maintained
between the user’s body and the handset, including the antenna. Third-party
belt-clips, holsters, and similar accessories used by this device should not
contain any metallic components. Body-worn accessories that do not meet these
requirements may not comply with RF exposure requirements and should be
avoided. Use only the supplied or an approved antenna.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>