PAX SK300 Smart Kiosk User Guide
- June 4, 2024
- Pax
Table of Contents
Quick Setup Guide
SK300 Smart Kiosk
PAX TECHNOLOGY LIMITED
Checklist
Congratulations on receiving your PAX Technology payment terminal. We do hope you enjoy it! The box you have just opened should contain the following items:
- 1 x PAX SK300 Smart Kiosk
- 1 x SK300 Hanging bracket
- 1 x Thermal Paper Roll
- 4 x M2.5*4 Combination Screw
- 1 x Power Adapter
- 1 x Power Supply cable
- 1 x Small screwdriver with cross slot (for SK300)
- 4 x ST5.0X40-PB Cross recessed countersunk head tapping screws with tip
- 4 x Screw expand rubber plug(5.0×40 self-tapping screw dedicated)
Product Description
Operating Instruction
- Power on: Plug in the AC power cable, press and hold the Power button for three seconds until the boot animation appears.
- Power off: Press and hold the Power button for three seconds until the shutdown menu displays. Select Power off. The terminal turns off after a few seconds.
Payment Options
-
Magnetic stripe card: Insert a magnetic stripe card into the card slot and push to the end with the magnetic stripe facing down, then pull out the card at a constant speed to swipe the card.
-
IC chip card: Insert card with IC chip facing up, then push it to the end of the card slot. Leave card inserted until prompted to remove.
-
Contactless card: Place the contactless card over the center of the contactless card reader logo area.
-
Scan: When the scan indicator is on, hold your QR code & bar code device in front of the scan window to scan the code.
Load Printer Paper
- Completely open the printer cover, Insert the new paper roll into the printer, and Close the printer cover.
Desktop Installation
- Completely open the printer cover, Insert the new paper roll into the printer, and Close the printer cover.
Parts List
| No. | Part | Picture | Qty/pcs |
|---|---|---|---|
| 1 | SK300 Kiosk | 1 | |
| 2 | Lock Two Screw | 2 | |
| 3 | M2.5*8 | ||
| Combination Screw | 4 |
Wall-mounted Installation
Parts List
| No. | Part | Picture | Qty/pcs |
|---|---|---|---|
| 1 | SK300 Kiosk | 1 | |
| 2 | Lock Two Screw | 2 | |
| 3 | M2.5*8 | ||
| Combination Screw | 4 | ||
| 4 | Hanging bracket | 1 |
Usage Tips
- There is no built-in battery, and the device can only be powered by the power adapter.
- Avoid exposing the device to in an overheated, humid, dusty, or strong electromagnetic environment.
- Do not vibrate, shake, or drop the device.
- Do not insert or unplug any part of the device while it is powered on. Otherwise, it may cause damage to the internal circuit.
- If necessary, please contact PAX technical support for assistance with the device.
- Before using the magnetic stripe /IC/contactless card, check if there is any suspicious person nearby, if so, pay attention to guard against theft.
Environmental Parameters
- Working Environment： Temperature:-10℃～50℃(32℉～113℉) (non-charging)
- Storage Environment： Temperature:-20℃～70℃(-4℉～158℉) (non-charging)
- Humidity：5%～96% (non-condensing)
Icons
| Dispose in a professional recycling manner
---|---
| Class II equipment
| For indoor use only
| Energy efficiency marking
| AC voltage
| DC voltage
| microSD logo
Trademark notice:
microSD logo is a trademark of SD-3C LLC.
FCC Statement
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To comply with RF exposure requirements, a minimum separation distance of 20mm must be maintained between the user’s body and the device, including the antenna.
IC STATEMENT
This device complies with Industry Canada Unlicenced-exempt RSS standard(s)
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. The end user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter.
To comply with RF exposure requirements, a minimum separation distance of 20mm must be maintained between the user’s body and the device, including the antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>