Pax Technology A920 Smart Mobile Payment Terminal Instructions

: October 27, 2023
: Pax Technology

Pax Technology A920 Smart Mobile Payment Terminal Instructions

A920 Smart Mobile Payment Terminal

1. Contents Checklist

Please check the components after unpacking. If any one of them is missing, or if there is a page missing from the product manual, ect., please contact the dealer.

Smart Mobile Payment Terminal	1
AC Power Adapter	1
Thermal Paper Roll	1
Battery	1
Cable	1
Product Manual	1

2. Installation

USB port:Connect USB device or PC. SAM/SIM card:
○1 Open the battery cover on the bottom of the terminal;
○2 Take out the battery;
○3 Insert SAM/SIM card into the corresponding SAM/SIM card slot. Micro SD card:
○1 Open the battery cove ron the bottom of the terminal;
○2 Take out battery;
○3 Insert Micro SD card into the corresponding Micro SD card slot.

3. Instruction

Power ON/OFF
Power on: press and hold the Power button for three seconds until the LCD is lighted up, and then the terminal is being turned on.
Power off: press and hold the Power button for three seconds until the shutdown menu appears, tap Power off > Power off, and then “Shutting Down” appears, the terminal is being turned off.
Magnetic Stripe Card
Place the magnetic stripe face down, swipe card through the magnetic card slot at a constant speed, which could be bi-directionally.
IC card
Place the chip face down, insert the IC card into the IC card slot, and push it to the end. 4）Tearing off paper
Tear the printing paper toward the 45 degree direction of the paper cutter.

Battery charging
User can charge the battery with power adapter, and the charging status will be displayed on the LCD.
6）Swiping contactless card
Place a contactless card close to the sensor area of swiping which is at the top of the terminal.

4. Installation and Usage Tips

Avoid putting the terminal in direct sunlight, high temperature, moist, dusty or explosive And reduce or eliminate vibration and direct pressure.
Forbid non-professional to repair the
Before insert the card, please check internal and around of IC card when you found some suspicious objects , must report to related administrator.

5. Parameter

Wireless Communication: Support WIFI ,WCDMA, LTE-FDD, LTE-TDD, UMTS/HSPA+, NFC.
Power Adapter:    Input: 100-240V AC, 50Hz/60Hz.
Output: 5.0V DC, 2.0A.
Battery:   Li-on battery, 52500mAh, 3.7V
Working Environment        Temperature: 0℃～50℃(32℉～122℉)
R.H.: 10%～93%( non-condense) Storage Environment Temperature:-20℃～70℃(-4℉～158℉)
R.H.:5％～95％ (non-condense)

6. Lithium Ion Battery Usage Tips

1）Avoid putting the battery in sunlight or smoke, dusty environment. 2）Forbid crushing, treading, throwing the battery into fire or liquid. 3）Replace the battery immediately if it is damaged(exothermic or distorted). 4）It is recommended changing battery that used more than two years.

7.Caution

Risk of explosion if battery replaced by an incorrect type. Dispose of used batteries according to the instructions.
Hereby, PAX Computer Technology (Shenzhen) Co., Ltd. declares that the radio equipment type A920 is in compliance with Directive 2014/53/EU.
To download the full text of the EU declaration of conformity, please visithttp://www.pax.com.cn/ProductCEquery.aspx?code=A920

7. Icon shows

Do not throw away, need professional recycling.

FCC Regulations:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

FCC RF Exposure Information (SAR)

This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States.
During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body. Although the SAR is determined at the highest certified power level, the actual SAR level of the while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.
The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.

The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on

FCC ID: V5PA920MG

To ensure that RF exposure levels below the levels tested, use accessories with this equipment to maintain a minimum separation distance of 1 cm between the body of the user and the device. For this device, the highest reported SAR value for usage near the body is 1.25 W/kg
While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement.

ISED Notice

This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the

IC: 11689A-A920MG

ISED Radiation Exposure Statement

This EUT is in compliance with SAR for general population/uncontrolled exposure limits in ISED RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEC/IEEE 62209-1528. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

This device has been tested for compliance with IC SAR values at a typical operating near the body. To ensure that RF exposure levels below the levels tested, use accessories with this equipment to maintain a minimum separation distance of 1 cm between the body of the user and the device. These accessories should not contain metallic components. It is possible that the accessories used close to the body that do not meet these requirements are not consistent with the SAR limits and it is advisable to avoid using them.