Pax Technology A77GT Smart Mini Payment Terminal User Manual
- June 3, 2024
- Pax Technology
Table of Contents
Pax Technology A77GT Smart Mini Payment Terminal
Contents Checklist
Please check the components after unpacking. If any one of them is missing, or if thereis a page missing from the product manual,etc.,please contact the dealer
Installation
TYPE_C port:Connect USB device or PC
SAM/SIM card:
- Open the battery cover on the bottom of the terminal;
- Take out the battery;
- Insert SAM/SIM card into the corresponding SAM/SIM card slot.
Micro SD card:
- Open the battery cover on the bottom of the terminal;
- Take out battery;
- Insert Micro SD card into the corresponding Micro SD card slot
Instruction
-
Power ON/OFF
Power on: press and hold the Power button for five seconds until the LCD besides, and then the terminal is being turned on.
Power off: press and hold the Power button for three seconds until the shutdown menu appears, tap Shutdown > Click Shutdown, and then “Shutting…†appears, the terminal is being turned off. -
Magnetic Stripe Card
Place the magnetic stripe face left, swipe card through the magnetic card slot at a constant speed. -
IC card
Place the chip face down, insert the IC card into the IC card slot, and push it to the end. -
Battery charging
User can charge the battery with power adapter, and the charging status will be displayed on the LCD. -
Swiping contactless card
Tap a contactless enabled card on the upper part of the surface of the screen where the contactless sensor is located. under the screen. The contactless area is placed inside of the screen.
Installation and Usage Tips
- Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment.
- Forbid non-professional to repair the terminal.
- Before insert the card, please check internal and around of IC card slot. when you found some suspicious objects , must reportto related administrator.
Lithium Ion Battery Usage Tips
WARNING:
- Don’t use the battery in sunlight or smoke, dust environment.
- Prohibited to strike, squeeze and tread on battery or throw it into the liquid and fire.
- If battery is impressive, deformed, damaged or exothermic seriously, please stop using immediately and replace it!
- If the continuous working time is only half of new one, the battery life may be end. Please replace it!
- Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
- Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;
- A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
- Charging time can not exceed 24 hours. If the battery is out of power, please recharge in time. Avoid damaging the battery in over-charge and over-discharge.
- If be non-use for long time, please recharge the battery per 6 months to avoid shortening its life.
- Suggest to replace it when the battery have been used for 2 years.
- Be sure to follow the instructions to dispose the wasted batteries.
CAUTION: Risk of explosion if the battery is replaced by an incorrect type or equivalent text
Icon shows
Do not throw away, need professional recycling.
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiated
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- -Consult the dealer or an experienced radio/TV technician for help.
Caution : Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
FCC RF Exposure Information (SAR)
- This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States.
- During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body. Although the SAR is determined at the highest certified power level, the actual SAR level of the while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.
- The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
- The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on
FCC ID : V5PA77GT
- While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement.
ISED Notice
This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause
ISED Radiation Exposure Statement
This EUT is in compliance with SAR for general population/uncontrolled
exposure limits in ISED RSS-102 and had been tested in accordance with the
measurement methods and procedures specified in IEEE 1528 and IEC 62209. This
device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
The device is going on be operated in 5150~5250 frequency range. It is
restricted indoor environment only in Canada.
PAX TECHNOLOGY LIMITED
- Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd.
- Address: 4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-Tech Industrial Park, Shenzhen, Guangdong, P.R.C.
- Tel: 0755-86169630
- Fax: 0755-86169634
- Website: http://www.pax.com.cn
- Responsible Party:PAX Technology, Inc. 8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300, Jacksonville , Florida, 32256
- Help-desk 1 877-859-0099
- P/N ：200312000000312
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>