SKYDANCE RM3 10-Key RF Remote Controller Instructions

June 4, 2024
SKYDANCE

10-Key RF Remote Controller
Model No.: RM3

1 zone RGB or RGBW/10-key/Wireless remote 30m distance/CR2032 battery

Features

  • Apply to RGB or RGBW LED controller.
  • Each remote can match one or more receivers.
  •  RC 2032 battery powered.
  • Operate with LED indicator light.

Technical Parameters

Input and Output

Output signal l RF 2.4GHz
Working voltage 3VDC CR2032
Working current <5mA
Standby current <2μA
Standby time 2 years
Remote distance 30m(Barrier-free space)

Environment

Operation temperature Ta: -30 OC ~ +55 OC
IP rating IP20

Safety and EMC

EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
---|---
Safety standard(LVD)| EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certification| CE,EMC,LVD,RED

Warranty

  Warranty  5 years

Mechanical Structures and InstallationsSKYDANCE RM3 10 Key RF Remote
Controller - fig

Match Remote Control (two match ways)
The end user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key Use Power Restart

Match:
Short press the match key,
and immediately press the on/off key on the remote.
The LED indicator fast flash a few times means the match is successful.
Delete:
Press and hold the match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted.| Match:
Switch off the power, then switch on the power, and repeat again.
An immediately short press the on/off key 3 times on the remote.
The light blinks 3 times means the match is successful.
Delete:
Switch off the power, then switch on the power, and repeat again.
An immediately short press on/off key 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.

Key function

| On/Off: Turn on/off the light.
---|---
| Color: Short press gets 24 kinds of static RGB color, and long press for continuous static color adjustment.

SKYDANCE RM3 10 Key RF Remote Controller - fig 1

| Mode+: Short press run the next dynamic mode, long press 2s run mode cycle.
---|---
| Mode -: Short press runs the previous dynamic mode, long press 2s run the first mode.
| Bright/Speed+: For static RGB color, increase brightness, short press 10 levels, and long press 1-6s for continuous 256 levels adjustment.
For dynamic mode, increase speed, short press 10 levels, long press get the fastest speed.
| Bright/Speed -: For static RGB color, decrease brightness, short press 10 levels, long press 1-6s for continuous 256 levels adjustment.
For dynamic mode, decrease speed, short press 10 levels, long press get the slowest speed.
| R/G/B: Short press gets red green or blue color directly, long press 1-6s adjust R/G/B brightness continuously to achieve millions of colors.
| W+/-: For RGB light, short press turn on/off white(RGB mix), long press 1-6s adjust saturation continuously
namely, change the current static RGB color to mixed white slowly.
For RGBW light, short press turn on/off W channel, long press 1-6s adjust W brightness continuously

Safety information

  1. Read all instructions carefully before you begin this installation.

  2. When installing the battery, pay attention to the battery’s positive and negative polarity.
    A long time without the remote control, remove the battery.
    When remote distance becomes smaller and insensitive, replace the battery.

  3. If no response from the receiver, please re-match the remote.

  4. Gently handle the remote, beware of falling.

  5. For indoor and dry location use only.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals