SW-MOTECH FRS.06.011.10200/S Ion Footrest Kit Instruction Manual

ANBAUANLEITUNG
mounting instructions
FRS.06.011.10200/S
contiene
FRS.06.011.80200/S
FRS.00.011.10000/S

MOUNTING INSTRUCTIONS

Revision: 00 Datum / Date: 10 – 2019
Mounting kit for ION footrest
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required le.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety, SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts le.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behavior and/or stability of your vehicle.

GENERAL INFORMATION

Observe the country: specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items on the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer’s specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with a medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation makes sure that all parts and connections previously removed are properly replaced. Also, make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
PRODUCT-SPECIFIC INFORMATION ATTENTION:
While cornering at extreme lean angles, ground clearance can be reduced by using this product!

PARTS LIST

Step| No.| Item No. / Description| Part| Quantity| **N.m***
---|---|---|---|---|---
2| (1)| FRS.06.011.A15L / R| Hinge Adapter; left / right| 2/2|
| (2)| M8 x 16; DIN 933; 10.9| Hexagon Screw| 2/2| 23
|  (3)| Ø8,4; DIN 9021; 300 HV| Washer| 2/2|
3**| (4)| DTI KEK.00.M6.ISK| Plastic Cap; black| 2/2|

8.8

10.9

• All measurements in millimeters.
  ** The second number indicates the total quantity of the part in the delivery.
  * No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications. 
  **

MOUNTING

NOTE: The installation is shown on the left side of the vehicle only. Repeat the same procedure on the right side of the vehicle with the appropriate parts.
NOTE: Before removing the original footrests, make sure to note the order and direction of the original fixing parts. Remove the original footrests on both sides of the vehicle.

NOTE: The marked part (I is included with the SW-MOTECH ION footrests IFRS.00.011.1000/).
Attach the footrests () to the hinge adapters (1).
A = original position (+/- 0 mm).
B = lower position (- 15 mm).
ATTENTION: Use a liquid thread locker! Tighten the screws (2) by hand.

Clean the footrest holder thoroughly. Apply some grease to the original bolts (Orig.).
Attach the hinge adapters (1) with the original parts (Orig.) on both sides of the vehicle.

ATTENTION: Secure the bolts (Orig.) with the original retaining rings (Orig.)! Tighten the screws (2) as specified.

Footrests
FRS.00.oiti0000/S
Revision: of
Mounting Instructions
All screws, bolts and nuts, including all replacement hardware provided by SW- MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used:

All screws, bolts and nuts should be checked after driving the first 5o km to ensure that all are tightened to the proper torque.
Medium strength liquid thread-locker (i.e., “Locktite”) should be used to secure all screws, bolts, and nuts.

SW-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg
Germany
Tel. +49 (o) 64 25/8 i6 8-oo
Fax +49 (0) 64 25/8 i6 8-io
info@sw-motech.com
www.sw-motech.com

|
---|---

Attention: Cornering and ground clearance can be reduced by using this accessory.

 GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg
Germany| Tel. / phone + 49 (016425 / 8168 – 050
Fax / fax + 49 (016425 / 8168 – 10
www.sw-motech.com
---|---

Packed by:
Date of packaging:
Copyright by SW-MOTECH GmbH & Co. KG
Technische and Design-Anderungen vorbehalten.
Errors and omissions excepted.
Technical and design modifications are subject to change.

Documents / Resources

| SW- MOTECH FRS.06.011.10200/S Ion Footrest Kit [pdf] Instruction Manual
FRS.06.011.10200 S, Ion Footrest Kit, FRS.06.011.10200 S Ion Footrest Kit, FRS.06.011.80200 S, FRS.00.011.10000 S
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>