SW-MOTECH BC.HTA.01.979.30000B URBAN ABS Side Case Set Instruction Manual
- June 4, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.HTA.01.979.30000B URBAN ABS Side Case Set
SAFETY ALERT SYMBOL
This safety alert symbol is used throughout these mounting instructions to warn of the possibility of death, bodily injury or other warnings. The words DANGER, WARNING and CAUTION are used with this safety alert symbol to convey important safety messages and information related to the installation and use of this product. These words along with the safety alert symbol mean:
- DANGER : Indicates a hazardous situation that, if not avoided, will result in death or serious injury!
- WARNING : Indicates a hazardous situation that, if not avoided, could result in death or serious injury!
- CAUTION : Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury!
- NOTICE : Important information, but not death or injury related (property damage only!
- WARNING: The installation and/or maintenance of this product requires advanced mechanical skills, the proper tools, and a thorough understanding of tool use and torque specifications.For of tools your use own and safety, sw-MOTECH recommends having installation and/or maintenance carried out by a qualified and certified motorcycle mechanic.
- WARNING: Should you choose to self-install this product, carefully and completely read all intallation and safety instructions before installation and use, and follow all the directions and safety precautions given in the mounting instructions to avoid serious injury or death. Also pay attention to all relevant information in the vehicle manual during installation and use.IF YOU D0 NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS, OR NEED CLARIFICATION OF ANY INSTRUCTION, DO NOT ATTEMT TO MOUNT THIS PRODUCT WITHOUT CONTACTING SW-MOTECH FOR ASSISTANCE.
- PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included.
- CAUTION: Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the engine/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools and wear always safety glasses and hand protection. Have another person help you.
- MOUNTING : All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer specifications or replaced by parts and hardware delivered by SW-MOTECH.
- WARNING: Secure all threads, unless otherwise specified, with medium- strong strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a certified motorcycle workshop!
- FUNCTION CHECK: After installation also make sure that no moving parts are obstructed, and function of the vehicle is not hindered in any way. Cables and hoses must not rub and/or be pinched.
- WARNING : Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all connections and the proper fit of the product. Installed accessories can change driving behavior/stability of the vehicle.
PARTS LIST
READ AND SAVE THESE MOUNTING INSTRUCTIONS
Note : ” All measurements in millimeters. ” The second number indicates
the total quantity of the part in the delivery. No torque specifications: Use
the torque defined by vehicle manufacturer! The standard torque in this table
can be used as long as it is within the vehicle manufacturer s
specifications.
MOUNTING
READ AND SAVE THESE MOUNTING INSTRUCTIONS
WARNING: Always wear eye and hand protection!
WARNING: Always use appropriate tools!
NOTICE: The mounting steps [1] to 13/ show the mounting of the left side
carrier. Mount the right side carrier in the same way. Attach the parts (2) to
(5) to the side
Remove the shown screws from the vehicle.
Attach the side carriers (1) to the vehicle.
WARNING: Use liquid thread locker!
Tighten the screws with the manufacturers’ specified torque.
PRODUCT SPECIFIC INFORMATION
NOTICE: Observe the country-specific regulations concerning vehicle registration/operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
Mounting Instructions
Urban ABS Side case
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required le.g. ABE
certifications), are also available for download at our webshop.
Installation and or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and / or servicing carried out by a specialist workshop SW-MOTECH assumes no
liability for damage caused by improper installation and / or maintenance
work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.This product was developed for
vehicles in their factory setting. Compatibility With original accessory parts
or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE
installing this product, make sure that all moving parts (e.g. the chain) are
in the original state of maintenance. Installed accessories can change the
driving behavior and / or stability of your vehicle.
GENERAL INFORMATION
- Observe the country-specific regulations concerning vehicle registration operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
- PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor / exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
- FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type. After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function, Cable and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving
and braking performance!
ATTENTION : Depending on the location of fixation, cornering and ground
clearance can be reduced by using this product!
ATTENTION : Before riding and at each stop levery 200 km) check proper
fixation of the product!
ATTENTION : The maximum vehicle load specified by the manufacturer must not be exceeded!
Parts List
Care
To clean the side case, use warm, soapy water and a soft, clean cloth. Rinse
with clean water. Do NOT use strong cleaning agents, rough cleaning tools or
high pressure washer! Clean the side case after riding in salty conditions, to
avoid damage from salt. Hard-to-open zippers can be loosened with a small
amount of talcum powder.
ATTENTION : Surface materials can experience color changes or fading when
exposed to direct sunlight for extended periods of time and by environmental
factors le.g., SM06, acid rain, etc.)! SW-MOTECH assumes no liability for
this.
Place the three locking openings of the side case onto the guide bolts of the
mounted SLC side carrier. Then press the side case slightly downward, until it
properly rests on the SLC side carrier.
ATTENTION : Make sure that all three guide bolts engage at the same time!
Pay attention to the clearly audible snap sound of the locking mechanism and
that the red marking under the slider is not visible! To release press the
slider downward.
ATTENTION : All components of the side case must not contact any hot or
moving parts of the vehicle! All parts should also remain 5 cm away from hot
parts of the vehicle and remain clear of the exhaust stream! After mounting,
make sure there are no clearance issues while the suspension is both
compressed and extended.
Open the mounted side case [1] to protect it against theft. Now press the locking button and turn it according to the arrow mark until the locking button engages. Then lock the closed zipper with the included lock [2 ]We recommend leaving the locking button in the closed position during the ride.
Use the included waterproof inner bag 3) to protect your luggage from moisture.
For easier loading of the side case (1), open the buckles and hook and loop
fasteners of the opening reductions, as shown in the
drawing.
ATTENTION : Make sure weight is evenly distributed between the left and
right side if you want to use both side cases! Make sure that the loanding is
secured against shifting during the ride!
ATTENTION : Never store pointy or sharp-edged objects, which could cause
injury to persons or damage to the vehicle/side case!