Kaysun KID-06 S Wired Remote Controller User Manual

Kaysun KID-06 S Wired Remote Controller User Manual

IMPORTANT NOTE:
Thank you very much for purchasing our product. Before using your unit, please read this manual carefully and keep it for future reference

Quick Start Guide

1. FIT BATTERIES
   

2. **SELECT MODE

**

3. SELECT TEMPERATURE
   

4. PRESS POWER BUTTON
   

5. POINT REMOTE TOWARD UNIT
   

6. SELECT FAN SPEED
   

NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a detailed description of how to use your air conditioner

SPECIAL NOTE

• Button designs on your unit may differ slightly from the example shown.
• If the indoor unit does not have a particular function, pressing that function’s button on the remote control will have no effect.
• When there are wide differences between “Remote controller Manual” and “USER’S MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.

Handling the Remote Controller

Inserting and Replacing Batteries

Your air conditioning unit may come with two batteries (some units). Put the batteries in the remote control before use

1. Slide the back cover from the remote control downward, exposing the battery compartment.
2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
3. Slide the battery cover back into place.
   

BATTERY NOTES

For optimum product performance:

• Do not mix old and new batteries, or batteries of different types.
• Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.

BATTERY DISPOSAL

Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

TIPS FOR USING REMOTE CONTROL

• The remote control must be used within 8 meters of the unit.
• The unit will beep when remote signal is received.
• Curtains, other materials and direct sunlight can interfere with the infrared signal receiver.
• Remove batteries if the remote will not be used more then 2 months.

NOTES FOR USING REMOTE CONTROL

The device could comply with the local national regulations

• In Canada, it should comply with CAN ICES3(B)/NMB-3(B).
• In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generated, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
• Changed or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

Button Of Functions

Remote Screen Indicators

Information are displayed when the remote controller is power up.

Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the actual operation, only the relative function signs are shown on the display window.

How to Use Basic Functions

Basic operation

ATTENTION! Before operation, please ensure the unit is plugged in and power is available.

COOL Mode

1. Press the MODE button to select COOL mode.
2. Set your desired temperature using the TEMP or TEMP button.
3. Press FAN button to select the fan speed in a range of AU-100%.
4. Press the ON/OFF button to start the unit
   

SETTING TEMPERATURE

The operating temperature range for units is 16- 30°C.
You can increase or decrease the set temperature in 0.5ºC.

AUTO Mode

In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT operation based on the set temperature.

1. Press the MODE button to select AUTO.
2. Set your desired temperature using the TEMP or TEMP button.
3. Press the ON/OFF button to start the unit.
   NOTE: FAN SPEED can’t be set in AUTO mode
   

FAN Mode

1. Press the MODE button to select FAN mode.
2. Press FAN button to select the fan speed in a range of AU-100%.
3. Press the ON/OFF button to start the unit.
   NOTE: You can’t set temperature in FAN mode. As a result, your remote control’s LCD screen will not display temperature.
   

DRY Mode (dehumidifying)

1. Press the MODE button to select DRY.
2. Set your desired temperature using the TEMP or TEMP button.
3. Press the ON/OFF button to start the unit.
   NOTE: FAN SPEED cannot be changed in DRY mode.
   

HEAT Mode

1. Press the MODE button to select HEAT mode.
2. Set your desired temperature using the TEMP or TEMP button.
3. Press FAN button to select the fan speed in a range of AU-100%.
4. Press the ON/OFF button to start the unit.
   NOTE: As outdoor temperature drops, the performance of your unit’s HEAT function maybe affected. In such instances, we recommend using this air conditioner in conjunction withother heating appliances.
   

Setting the TIMER

TIMER ON/OFF – Set the amount of time after which the unit will automatically turn on/off.

TIMER ON setting

1. Press TIMER button to initiate the ON time sequence.

2. Press Temp. up or down button for multiple times to set the desired time to turn on the unit.
   

3. Point remote to unit and wait 1 sec, the TIMER ON will be activated.

TIMER OFF setting

1. Press TIMER button to initiate the OFF time sequence.

2. Press Temp. up or down button for multiple times to set the desired time to turn off the unit.
   

3. Point remote to unit and wait 1 sec, the TIMER OFF will be activated.

NOTE:

1. When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24.
2. Cancel either function by setting its timer to 0.0h.

TIMER ON & OFF setting (example)

Keep in mind that the time periods you set for both functions refer to hours after the current time.

Example: If current time is 1:00PM to set the timer as above steps, the unit will turn on 2.5h later (3:30PM) and turn off at 6:00PM

How to Use Advanced Functions

Vane function

Press Vane button when the unit is turned on.

The system will exit the louver setting mode if there is no operations during a 10 seconds period.

Press this button to activate the louver setting feature. Each time you press the Vane button, the display panel will display the selected louver in an order as (“-0” indicated that four louvers are all selected):

Press Swing button to start/stop the auto swing feature of the selected louvers.

Swing function

Press Swing button

The horizontal louver auto swing feature is energized. Press again to make it stop

FP function

Press this button 2 times during one second under HEAT Mode and setting temperature of 16ºC.

The unit will operate at high fan speed (while compressor on) with temperature automatically set to 8ºC

Note: This function is for heat pump air conditioner only.
Press this button 2 times during one second under HEAT Mode and setting temperature of 16ºC to activate the FP function. Press On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function

ECO/GEAR function

Press this button to enter the energy efficient mode in a sequence of following:
ECO → GEAR(75%) → GEAR(50%) → Previous setting mode → ECO…… Note: This function is only available under COOL mode

ECO operation:
Under cooling mode, press this button, the remote controller will adjust the temperature automatically to 24°C, fan speed of Auto to save energy (only when the set temperature is less than 24°C. If the set temperature is above 24°C, press the ECO button, the fan speed will change to Auto, the set temperature will remain unchanged.

NOTE:
Pressing this button, or modifying the mode or adjusting the set temperature to less than 24ºC/75ºF will stop ECO operation.
Under ECO operation, the set temperature should be 24ºC or above, it may result in insufficient cooling. If you feel uncomfortable, just press the ECO button again to stop it.

GEAR operation:
Press this button to enter the GEAR operation as following:
75% (up to 75% electrical energy consumption)
↓
50% (up to 50% electrical energy consumption)
↓
Previous setting mode.
Under GEAR operation, the display on the remote controller will alternage between electrical energy consumption and set temperature.

Silence function

Keep pressing Fan button for more than 2 seconds to active/disable Silence function (some units).
Due to low frequency operation of compressor, it may result in insufficient cooling and heating capacity. Press ON/OFF, Mode, Sleep, Boost or Clean button while operating will cancel silence function.

LOCK function

Press together the two buttons at the same time more than 5 seconds to activate Lock function. All buttons will not response except pressing these two buttons for two seconds again to disable locking.

SET function

• Press the SET button to enter the function setting, then press SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area, press the OK button to confirm.
• To cancel the selected function, just perform the same procedures as above.
• Press the SET button to scroll through operation functions as follows: Active clean Fresh  Sleep   Follow MeAP mode Active clean… Model dependent

Active clean function (some units):
The Active Celan Technology washes away dust, mold, and grease that may cause odors when it adheres to the heat exchanger by automatically freezing and then rapidly thawing the frost. When this function is turned on, the indoor unit display window appears “CL”, after 20 to 45 minutes, the unit will turn off automatically and cancel CLEAN function.

Sleep function :
The SLEEP function is used to decrease energy use while you sleep (and don’t need the same temperature settings to stay comfortable). This function can only be activated via remote control. For the detail, see sleep operation in “USER’S MANUAL”.
Note: The SLEEEP function is not available in FAN or DRY mode.

FRESH function (some units):
When the FRESH function is initiated, the ion generator is energized and will help to purify the air in the room.

Follow me function :
The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3 minutes interval.

When using AUTO, COOL or HEAT modes, measuring ambient temperature from the remote control (instead of from the indoor unit itself) will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.

NOTE:
Press and hold Boost button for seven seconds to start/stop memory feature of Follow Me function.

• If the memory feature is activated, “On” displays for 3 seconds on the screen.
• If the memory feature is stopped, “OF” displays for 3 seconds on the screen.
• While the memory feature is activated, press the ON/OFF button, shift the mode or power failure will not cancel the Follow me function

AP function (some units):
Choose AP mode to do wireless network configuration. For some units, it doesn’t work by pressing the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.

MAIN OFFICE
Blasco de Garay, 4-6
08960 Sam Just Desvern
(Barcelona)
Tel. +34 93 480 33 22
http://www.frigicoll.es/
http://www.kaysun.es/en/

MADRID
Senda Galiana, 1
Poligono Industrial
Coslada Coslada (Madrid)
Tel. +34 91 669 97 01
Fax. +34 91 674 21 00
madrid@frigicoll.es

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>