Taramps THS 1800 Multi Channel Receiver Instruction Manual

Taramps THS 1800 Multi Channel Receiver

Product Information

The TARAMPS THS 1800 is a Multi-Channel Receiver with a power output of 4 x 20W RMS CLASS AB. It has multiple audio inputs, including USB, Micro SD card, AUX (P2 connector), AUX1 and AUX2 (RCA connectors), Bluetooth, and FM radio. The equipment is bivolt and can be connected to any power plug between 90 and 240V. It has a switching power supply that is more efficient in the consumption of electricity. The THS 1800 supports MP3 music files and can read up to 64GB of storage.
It is important to note that infected devices connected to the THS 1800 may cause undesirable effects, such as slow music reading and general failures. Therefore, it is recommended to have a good antivirus and avoid using the USB input to connect to computers or recharge other devices with batteries.
The package content includes the THS 1800 Multi-Channel Receiver.

Product Usage Instructions

1. Installation : The THS 1800 should be installed in a cool and well-ventilated location, away from heat sources.
2. Power Connection : Connect the THS 1800 to a power outlet. The LED STAND BY will light up when the equipment is turned off and connected to the power outlet.
3. Audio Source : Connect your desired audio source to one of the available inputs on the front panel or rear panel of the THS 1800. The available inputs include USB, Micro SD card, AUX (P2 connector), AUX1 and AUX2 (RCA connectors), Bluetooth, and FM radio.
4. Bluetooth Usage: To use Bluetooth, ensure that your device (Android or iOS) is paired with the THS 1800. Follow the instructions provided by your device’s manufacturer. Once paired, you can play audio from your device through the THS 1800.
5. Using RCA Connectors: If you plan to connect a device using RCA connectors, such as a DVD player, follow the illustrated example provided in the user manual. Connect the positive and negative terminals of the device to the corresponding terminals on the THS 1800.
6. Additional Controls : The front panel of the THS 1800 includes various controls for playback and volume adjustment. Refer to the user manual for detailed information on each control’s function.
7. Power Consumption : The THS 1800 consumes approximately 1.4W in standby mode.

For more information or assistance, refer to the warranty terms provided by Taramps Electronics or contact their customer support.

Note: The text provided is a partial extract from the user manual. For complete and accurate instructions, please refer to the original user manual provided with the product.

Introduction

• Congratulations on purchasing a Taramps product.
• Developed in a modern laboratory, with highest technology and highly qualified professionals.
• This manual explains all the resources, operations and guidelines for resolving questions that may arise in your installation. Take a time to read it carefully and ensure the proper installation and use of all the benefits that this product can offer.
• In case of doubt even after reading this manual, please contact our technical support at the number +55 18 3266 4050 or our website www.taramps.com.br.

Presentation
The TARAMPS THS 1800 is a Multi Channel Receiver developed with high technology to integrate different environments. Compact and powerful it can be used in several applications providing quality sound.

Application examples

• Environment sound for stores, shops and clinics. It also allows, through the microphone input, that warnings are transmitted via the sound system.
• In your leisure area, gourmet space, country house, etc. Including various audio input options, such as Bluetooth, AUX and USB, it allows the audio sources to be easily changed giving the user ?exibility in choosing the preferred audio.

The equipment is automatic bivolt and can be connected to any power plug between 90 and 240V. It has a switching power supply that is more efficient in the consumption of electricity.
If you are not going to use the product for a long time, we recommend that you disconnect from the power plug.

Important recommendations

• The THS 1800 must be installed in a ?rm and ventilated place, away from heat and humidity places. Avoid locations with direct sunlight.
• Do not block the ventilation holes on the top and rear.
• Avoid falls and impacts.
• Carefully observe the polarity and impedance of the loudspeakers.
• Use cables according to the distance between the THS 1800 and the loudspeakers.

The table below shows the recommended gauges according to the distances

mm²

• In case of unwanted noise make sure that the cables and connections are in good condition. Leave the volume to a minimum of unused channels.

Audio source
The TARAMPS THS 1800 has the following audio inputs

1. USB : Flash drive input
2. MICRO SD CARD
3. AUX (front): P2 standard auxiliary input.
4. AUX1 and AUX2: RCA standard auxiliary inputs.
5. BLUETOOTH
6. FM radio

• The connected device must contain music in MP3 format to be identi?ed by the equipment.

  • Maximum supported size: 64GB.
  • We advise you to always have a good antivirus, so there are no problems with the Flash Drive or micro SD card when connecting to the product. Infected devices may cause undesirable effects to the THS 1800, such as: Slow music reading and general failures.
  • Do not use the USB input to connect to the computer or to recharge other devices that have batteries.

Package content

1. Multi Channel Receiver THS 1800

1. Remote Control

Knowing your equipment

Front Panel

1. MICRO SD : Micro SD memory card input. shows, with the terminals facing up) (The card must be positioned as the image

2. USB : Flash Drive input.

3. Aux. (P2 Connector): Receives audio signal from the P2 output of your phone, tablet, MP3, computer, among others. Use good quality cable to avoid unwanted noise.

4. Short Touch (Track-): Rewind the music tracks in the USB/SD/BLUETOOTH.

   • Long Touch (Volume -): Reduce the volume in all sources options.
   • FM : Short Touch: Reduce 0.1MHz of the frequency.
   • Long: Automatic search to previous stations.

5. Short Touch (Play / Pause): Pause or start the music on USB / SD / BLUETOOTH.

   • Short Touch: Mute for AUXILIARY option
   • FM : Short Touch: Advances next saved memory position of FM stations.
   • Long: Searches for FM stations and saves them in memory.

6. Short Touch: (Track+): Forward the music tracks in the USB/SD/ BLUETOOTH.

   • Long Touch :(Volume +): Increase the volume in all sources options
   • FM : Short Touch: Increase 0.1MHz of the frequency.
   • Long: Automatic search to next stations.

7. Short Touch(Source): Changes the source options, such as: USB / SD / AUXILIARY / BLUETOOTH / FM.

   • Long Touch – ON / OFF – To turn on or off the device.

8. LED Display – Remote control IR sensor: For better communication between the remote control and the device, point the control at this point on the display.
   Front Panel (sequence)

9. STAND-BY LED: Remains on when the equipment is turned off and plugged into a powered outlet.

10. EQUALIZATION: 3 band audio equalizer adjust.

    • LOW : Bass frequencies
    • MID: Middle frequencies
    • HIGH : High frequencies.

11. VOL CH 1 / CH2: Adjusts the output volumes CH1 / CH2 (L e R) VOL CH 3 / CH4: Adjusts the output volumes CH3 / CH4 (L e R).

Mix Mode

• To enable the Mix Mode, slide the switch key under the device to the ON position. For this use a small screwdriver and keep the power cord unplugged.
• In mixed mode the 4 outputs have the same sound, (no longer being stereo L and R) allowing, for example, the distribution of the sound over 4 different rooms without channel loss.

Knowing your equipment
Rear Panel

1. POWER CABLE: Connect the cable to a powered outlet. This product operates from 90V AC to 240V AC 50Hz/60Hz

2. VENTILATION HOLES: Do not obstruct the rear and the upper ventilation (cover) for better performance of the product.

3. SPEAKER OUT: To connect the loudspeakers. Follow the indicated polarity and the recommended minimum impedance of 4 ohms for each channel.

4. LINE OUT : The LINE OUT output allows you to send the audio signal (not amplified) to other equipment, such as a THS 3600, an active amplifier or subwoofer.
   This signal goes through the equipment’s equalization settings (LOW, MID and HIGH).

5. AUX INPUT: L and R (RCA) input works in parallel with the front AUX input (connector P2).

6. FM ANTENNA : Indoor wire antenna for FM radio reception. Position the wire antenna in order to achieve the best FM reception.

Remote control functions
The THS 1800 has a compact remote control, so you can remotely control the device with practicality.

• ON / OFF: Press the key to turn off the device.
• MODE: Switch the audio source (USB, BLUETOOTH, SD, AUXILIARY, FM).
• MUTE
• PLAY / PAUSE: Pause or start the music to USB / SD / BLUETOOTH.
  • FM: Short Press: Advances next saved memory location of FM stations.
  • Long Press : Searches for FM stations and saves them in memory.
• TRACK – Previous track (short press)
  • FOLDER – Previous folder (long press)
  • FM: Short Press: Previous 0.1MHz of the frequency.
  • Long Pres s: Automatic search to the previous station.
• TRACK + Next track (short press)
  • FOLDER + Next folder (long press)
  • FM: Short Press: Next 0.1MHz of the frequency.
  • Long Pres s: Automatic search to the next station.
• EQUALIZATION: Pop / Rock / Jazz / Country / Normal.
  • Do not work in auxiliary mode.
  • FM: Short Press Return to the saved memory position of FM stations.
• VOL-: Volume down
• VOL+: Volume up
• REPEAT: Repeat /play MP3 options
• U/SD: Switch mode between USB / SD Card
  • FM: Searches for FM stations and saves them in memory.
  • NUMERIC KEYBOARD: FM: Long Press saves FM stations.

Bluetooth
When selecting the Bluetooth function (identi?ed with “bt” on the display), the THS 1800 waits for a Bluetooth connection. Search for the device called “TARAMPS” using your phone, tablet, PC or other and match it.

• To connect to a new device, disconnect the current one and make the new Bluetooth pairing.
• Bluetooth speciation: class II with a 10m maximum range and may vary according to the environment (such as walls) and the connected device.

For other devices the connection system is similar (consult manufacturer’s manual)

Bluetooth use example

Some TVs have an audio output system via Bluetooth. If your TV has this feature, it’s possible to transmit the audio to the THS 1800.
Consult your TV manufacturer’s manual.

Example of using an RCA connection
Select the AUX function on the ‘‘SOURCE’’’ key.

Connect control use example (Long range transmitter)
The THS 1800 is compatible with the CONNECT CONTROL, TARAMPS long range remote control which allows you to control your sound over wide distances and without the need to point the control at the device. The THS 1800 does not lose the functionality of the USB port, as the connect control allows a Flash Drive to be plugged into its USB port.

• • For more details on the CONNECT CONTROL TARAMPS functionalities consult in its manual on the website.

NOTE: Connect Control Taramps is sold separately.

Connection examples – Wall sconces
Examples to until 8 loudspeakers 8 ohms each

For this kind of connection use cables with a minimum gauge of 1.5mm² for up to 40 meters. For long distances, consult the table on page 12 ‘‘Important recommendations’’. It’s necessary to make connections in parallel and series as shown in the example, to match impedance.

Term of warranty

• Located at Rua Abílio Daguano, 274 Res. Manoel Martins – Alfredo Marcondes – SP, ZIPCODE 19.180-000, TARAMPS guarantees this product against defects in design, manufacture, assembly and / or jointly due to design flaws that make it inappropriate or unsuitable for the intended use, for a period of 12 months from the date of acquisition.
• In case of a defect in the warranty period, TARAMPS is responsible for the repair or replacement of the device manufactured by it.

This warranty excludes

• Products damaged by improper installation, water infiltration, violation by unauthorized persons;
• Torn or torn warranty seal;
• Cases where the product is not used under normal conditions;
• Defects caused by accessories, modifications or equipment attached to the product;
• The product shows damage due to falls, impacts or the action of agents of nature (floods, lightning, etc.);
• Costs of removing and reinstalling the equipment, as well as transporting it to the technical assistance station;
• Damage of any nature, resulting from product problems, as well as losses caused by interruption of use.

Technical assistance
We have technical assistance all over Brazil and we are always ready to answer your questions and needs. To locate an electronic Taramps technical assistance near you, access our website
www.taramps.com.br/pt/rede-de-assistencias- tecnicas or contact the factory’s technical assistance department

Taramps Eletronics

• Rua Abílio Daguano, n 274
• ZIPCODE: 19.180-000
• Phones + 55 18 3266-4050 / +55 18 99749-3391
• E-mail: service@taramps.com.br

Technical features

• • Nominal power with 1KHz sinusoidal signal and 4 ohms resistive load. (Measured according to ABNT NBR IEC 60268-3 sound equipment, Part 3: Amplifiers).
    The values mentioned are typical and may change due to the tolerance of components or the manufacturing process. For more information or questions visit our website or contact TARAMPS support.

Taramps reserves the right to modify the contents of this manual without prior notice and not to apply the modifications to units previously produced.

• +55 18 3266-4050
• Fabricado por / Manufactured by: TARAMPS ELECTRONICS LTDA
• CNPJ / TAX ID: 11.273.485/0001-03
• R. João Silvério, 121 • Res. Manoel Martins Alfredo Marcondes – SP
• Indústria Brasileira – Made in Brazil
• www.taramps.com.br

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>