PRINSU 2023-Current Toyota Sequoia Roof Rack Instruction Manual

: June 13, 2024
: PRINSU

Table of Contents

PRINSU 2023-Current Toyota Sequoia Roof Rack
Applications
IMPORTANT!
Hardware
Tools Required
Sequence of Steps
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PRINSU 2023-Current Toyota Sequoia Roof Rack

PRINSU-2023-Current-Toyota-Sequoia-Roof-Rack-product

Applications

These installation instructions apply to the following Prinsu products

Sequoia Prinsu Rack | 2022- Present

IMPORTANT!

THANK YOU for purchasing this Prinsu product. Please read through this entire document before proceeding with installation. If you are not confident in your mechanical skills, please seek the help of a professional to perform the installation. Check your packages immediately upon arrival to ensure that everything listed is included, and to check for damage during shipping. If anything is missing or damaged, or if you need technical assistance with any aspect of this installation, call Prinsu at 208-528-0664 as soon as possible.

IMPORTANT!
If your Prinsu product comes as unpainted, bare steel, or aluminum. You will want to either powder-coat or paint prior to final installation, however, it is very important to PRE-INSTALL the unpainted product first, following these instructions, BEFORE painting or powder-coating any of the components! This will ensure that all parts are correct and that any incidental trimming or drilling will have been done prior
to coating. Also, it will give you a practice run to familiarize yourself with the process, to lessen the likelihood of damaging the finish during the final installation. Prince is NOT RESPONSIBLE for paint or powder coating costs, damage to paint or powder coating, or costs associated with inadvertently painting or powder coating components that are defective or were shipped or assembled in error. It is the customer’s responsibility to pre-install and verify that all parts are correct prior to paint or powder coat

Hardware

Moun%ng Hardware
DESCRIPTION QTY

M8-1.25 x 40 mm Steel Hex Flange Bolt Zinc 5
M8-1.25 x 20 mm Steel Hex Flange Bolt Zinc 5
1/4″-20 x 1″ Steel 6-Lobe Pan Machine Screw Black Zinc 16
1/4″ x .557″ – .567″ x .044″ – .052″ Steel Flat Washer 16

Wind Deflector Hardware
DESCRIPTION QTY

1/4″-20 Steel T-nut Plain 12
1/4″-20 x 1/2″ Steel Pan Head Phillips Black Zinc 12
1/4″ x .557″ – .567″ x .044″ – .052″ Steel Flat Washer 12
52″ Cross Bar Hardware (For 11 Cross Bars)

DESCRIPTION QTY

1/4″-20 Steel T-nut Plain 12
1/4″-20 x 1″ Steel 6-Lobe Pan Machine Screw Black Zinc 46
1/4″ x .557″ – .567″ x .044″ – .052″ Steel Flat Washer 46

Tools Required

Black RTV Silicone
Flat Head Screwdriver
T-30 Torque Bit
Phillips Head Screwdriver
7/16” Wrench
12mm Socket or wrench
13mm Socket or wrench
Side Cutting Pliers

Note for Dealers and Installers
It is your responsibility to ensure instructions are given to the end-user or client.

Questions?
Call: 866-522-0697
Email: info@cbioffroadfab.com

Sequence of Steps

Prep and Layout

The first step is to lay out a soft blanket to protect your pieces and keep them organized.
Unpack the box that your Prinsu Rack came in and confirm that you received all of the hardware and bracketry listed above.
Now take all of the black bolts and prep them with a black washer and a drop of Vibra-tite.
Next bolt the front side rail to the rear side rail using the side rail connector bracket make sure to use the top two holes and the Torque bolts. Just snug them up don’t over-tighten.
Install the mounting feet to the appropriate side rail. The brackets are labeled as such only mount the DM, DR, PM, and PR feet for now.
Df-driver side front, DM-driver middle, DR-driver rear, PF-passenger front, PM-passenger middle, PR-passen-ger rear. Only mount the DM, DR, PM, and PR feet for now.
Repeat on the other set of side rails.

Mounting Rack to the Vehicle

Locate the plastic covers on your factory rack, there should be two on each side.
Take a flathead screwdriver and pry the covers off like the photo below.
Remove the factory bolt in all four locations.
Apply some black RTV silicone into the exposed roof holes and Install the supplied mounting block with the longer M8 Bolt in the holes where you just removed the factory bolts.
Now hold the appropriate side rails in place (side rails will be installed on the outside of the factory roof rack rails) and mount to the blocks using the shorter M8 bolts with some Vibra-Tite applied.
Repeat on both sides
Now you can start installing the cross bars into the smaller slots in the side rails. Cross bars will be mounted using the Torque head bolts. Start all bolts by hand and tighten down with a T-30.
Now we can install the DF, and PF mounting feet. Clean the area where the 3m tape will contact the roof and the mounting foot.
Apply 3m tape to the bottom of the mounting foot
Line up the mounting holes adhere the foot to the roof and install the mounting bolts in the side rail.
The silver-colored crossbar will be installed on the wind deflector. Slide 5 T nuts into the top channel and 5 into the bottom channel and line them up with the holes in the wind deflector.
Set the wind deflector on top of the silver cross bar and line up the holes with the nuts.
Start the Phillips head bolts, once all the bolts are started tighten them down.
Now install noise-reducing trim onto the wind deflec-tor and trim off the excess.
The wind deflector is now ready to be installed onto the vehicle.
Double-check the alignment of the rack and make sure all bolts have been tightened down.