SUNRICHER SRP-ZG9105N-65CC500 65W 1CH Zigbee NFC Enabled LED Driver Instruction Manual

SRP-ZG9105N-65CC500 65W 1CH Zigbee NFC Enabled LED Driver

“`html

Product Specifications

Product Data

• Output Input Control Current: 500-1500mA via NFC setting;
  Min.current gear lower to 0.1mA, Default 1050mA

• Current Accuracy

• Rated Power: Max. 65W

• Voltage Range: 200-240VAC/200-240VDC 176-264VAC/176-280VDC

• Frequency Range: 0/50/60Hz

• Power Factor (Typ.): > 0.98 @ 230VAC Full load

• Total Harmonic Distortion: THD 6% (@ full load / 230VAC)

• Efficiency (Typ.): 90% @ 230VAC full load

• AC Current (Typ.): 0.4A @ 230VAC

Product Usage Instructions

Operation – Zigbee Network

1. Do wiring according to connection diagram correctly.

2. This ZigBee device is a wireless receiver that communicates
   with a variety of ZigBee compatible systems. This receiver receives
   and is controlled by wireless radio signals from the compatible
   ZigBee system.

3. Zigbee Network Pairing through Coordinator or Hub (Added to a
   Zigbee Network):

4. Remove the device from the previous zigbee network if it has
   already been added to, otherwise pairing will fail.

5. From your ZigBee Controller or hub interface, choose to add
   lighting device and enter Pairing mode as instructed by the
   controller.

6. Power on the device, it will be set into network pairing mode
   (connected light flashes twice slowly), the network pairing mode
   will last until the device is added to a zigbee network.

7. Connected light will blink 5 times and then stay solid on, then
   the device will appear in your controller’s menu and can be
   controlled through the controller or hub interface.

8. TouchLink to a Zigbee Remote:

9. Method 1: re-power on the device 4 times to start Touchlink
   commissioning immediately, 180S timeout, repeat the operation.

10. Method 2: If the device is already added to a network, it will
    be set into Touchlink commissioning immediately, 180S timeout. Once
    timeout, re-power on the device to set it into touchlink
    commissioning again.

Frequently Asked Questions (FAQ)

Q: How do I reset the device?

A: To reset the device, remove it from the
current Zigbee network and power it off and on again.

“`

65W 1CH Zigbee NFC Enabled LED Driver(Constant Current)

Important: Read All Instructions Prior to Installation Function introduction
LED Output –

LED OUTPUT

Zigbee Dimmable Driver

AC Push

INPUT

ACL/

AC/DC power input

DC+ ACN/

DC-

Product Data

LED Channel DC Voltage

1 6-54V

Output Input Control

Current

500-1500mA via NFC setting; Min.current gear lower to 0.1mA,Default 1050mA

Current Accuracy

±3%( ±1%@Certain full load) @ full load

Rated Power
Voltage Range
Absolute Voltage Range
Frequency Range Power Factor (Typ.)
Total Harmonic Distortion
Efficiency (Typ.)
AC Current (Typ.) Inrush Current (Typ.)
Leakage Current
Standby Power Consumption
Anti Surge Dimming Interface

Max. 65W
200-240VAC/200-240VDC 176-264VAC/176-280VDC
0/50/60Hz > 0.98 @ 230VAC Full load THD 6% (@ full load / 230VAC) 90% @ 230VAC full load
0.4A @ 230VAC Max. 9.68A at 230VAC; 70s duration
< 5mA /230VAC 0.5W L-N:2KV Zigbee

Dimming Range

0.01%-100%@ Max current

Dimming Method

Amplitude/CCR dimming

Dimming Curve

Linear/ Logarithmic optional

Short Circuit

Yes, remove the fault conditions and re-power the device

Protection

Over Current

Yes, remove the fault conditions and re-power the device

Over Temperature

Yes, remove the fault conditions and re-power the device

Working Temp.

-25 ~ +45

Max. Case Temp. Environment
Working Humidity
Storage Temp. & Humidity
Safety Standards

TC=85 (Ta=”45″) 10% ~ 95% RH non-condensing -40 ~ +80, 10% ~ 95% RH
EN61347-1, EN61347-2-13

Safety & EMC

Withstand Voltage Isolation Resistance
EMC Emission

I/P-O/P: 3.75KVAC I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH
En55015, EN61000-3-2, EN61000-3-3

EMC Immunity

En61547, EN61000-4-2,3,4,5,6,8,11

Others

MTBF
Dimension Warranty

191350H, MIL-HDBK-217F @ 230VAC full load and 25 ambient temperature
123.9×78.8x30mm (LWH) 5 Years

· Dimmable LED driver, ZigBee device based on ZigBee 3.0 protocol · Dimmable LED driver. Max. output power 65W · 500-1500mA current selectable via NFC program tool. Min.current gear lower to 0.1mA · Dimming curve/Power on state/Soft start/Soft off via NFC program tool. · Class power supply, full isolated plastic case · High power factor and efficiency · PUSH DIM function enabled · Able to On/Off and control LED lighting luminaries` brightness and color temperature · Amplitude/CCR dimming, smooth and deep dimming · ZigBee end device that supports Touchlink commissioning · Can directly pair to a compatible ZigBee remote via Touchlink · Supports find and bind mode to bind a ZigBee remote · Supports zigbee green power and can bind max. 20 zigbee green power switches · Compatible with universal ZigBee gateway products · Waterproof grade: IP20, suitable for indoor LED lighting applications · 5 years warranty

Safety & Warnings · DO NOT install with power applied to the device. · DO NOT expose the device to moisture.

Operation–Zigbee Network
1.Do wiring according to connection diagram correctly.
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller. Step 3: power on the device, it will be set into network pairing mode (connected light flashes twice slowly), the network pairing mode will last until the device is added to a zigbee network.

LED OUTPUT

–
LED
Zigbee Dimmable Driver

AC Push

LN

ACL/ DC+ ACN/ DC-

INPUT

Step 4: Connected light will blink 5 times and then stay solid on, then the device will appear in your controller’s menu and can be controlled through controller or hub interface.

4. TouchLink to a Zigbee Remote
Step 1: Method 1: re-power on the device 4 times to start Touchlink commissioning immediately, 180S timeout, repeat the operation. Method 2: If the device is already added to a network, it will be set into Touchlink commissioning immediately, 180S timeout. Once timeout, re-power on the device to set it into touchlink commissioning again.

LED OUTPUT

LED
< 10cm
Zigbee Remote
LN

INPUT

AC Push

–
Zigbee Dimmable Driver
ACL/ DC+ ACN/ DC-

Step 4: There shall be indication on the remote for successful link and connected light will flash twice.

Step 2: Bring the remote or touch panel within 10cm of the lighting device. Step 3: Set the remote or touch panel into Touchlink commissioning, please refer to corresponding remote or touch panel manual to learn how.
Note: 1) Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote. 2) TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes. 3) To control by both gateway and remote, add remote and device to network first then TouchLink. 4) After TouchLink, the device can be controlled by the linked remotes.

5. Removed from a Zigbee Network through Coordinator or Hub Interface
From your ZigBee controller or hub interface, choose to delete or reset the lighting device as instructed. The connected light blinks 3 times to indicate successful reset.

6. Factory Reset Manually Step 1: Enable Pairing via NFC App or re-power on the device for 5 times continuously .

LED OUTPUT

–

LED

Step 2: Connected light will blink 3

Zigbee Dimmable Driver

times to indicate successful reset.

AC Push

INPUT

ACL/ DC+ ACN/ DC-

LN

Note: 1) If the device is already at factory default setting, there is no indication when factory reset again . 2) All configuration parameters will be reset after the device is reset or removed from the network.

7. Find and Bind Mode Step 1: Re-power on the device (initiator node) 3 times to start Find and Bind mode (connected light flashes slowly) to find and bind target node, 180 seconds timeout, repeat the operation.

LED OUTPUT

Zigbee Remote

INPUT

AC Push

–
LED
Zigbee Dimmable Driver
ACL/ DC+ ACN/ DC-
LN
Step 2: Set the remote or touch panel (target node) into find and bind mode, and enable it to find and bind initiator, please refer to corresponding remote or touch panel manual. Step 3: There shall be indication on the remote or touch panel that it bind the device successfully and can control it then.

8. Learning to a Zigbee Green Power Switch
Step 1: Re-power on the device 4 times to start Learning to GP switch mode (connected light flashes twice), 180 seconds timeout, repeat the operation.

LED OUTPUT

Zigbee Green Power Switch

–
LED
Zigbee Dimmable Driver

AC Push

ACL/ DC+ ACN/ DC-
LN
Step 2: Set the green power switch into Learning mode, please refer to its manual.

INPUT

Step 3: Connected light will flash twice to indicate successful learning. Then the switch can control the device.
Note: Each device can learn to max. 20 zigbee green power switches.

9. Delete Learning to a Zigbee Green Power Switch
Step 1: Re-power on the device 3 times to start delete Learning to GP switch mode (connected light flashes slowly), 180 seconds timeout, repeat the operation.

LED OUTPUT

Zigbee Green Power Switch

INPUT

AC Push

–
LED
Zigbee Dimmable Driver
ACL/ DC+ ACN/ DC-
LN
Step 2: Set the paired green power switch into Learning mode, please refer to its manual.

Step 3: Connected light will flash 4 times to indicate
successful deleting.

10. ZigBee Clusters the device supports are as follows:

Input Clusters

· 0x0000: Basic · 0x0003: Identify

· 0x0004: Groups

· 0x0005: Scenes

· 0x0008: Level Control · 0x0300: Color Control

· 0x0b05: Diagnostics

Output Clusters

· 0x0019: OTA

· 0x0006: On/off

11. OTA The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically.

Function setting Via “SR NFC TOOL” Enter Zigbee Functions

4 Different settings.

1. A. Enable the Zigbee NFC drivers enter the pairing mode and add it into the Zigbee network. B. Factory reset. Enable the configured Zigbee NFC driver into configuring mode. C. Besides, you can re-power the device 5 times to enable this section as well.

2. A. Remember, once you need to write other parameters into the NFC driver, you should select this section, so as not to change the driver’s state.

3. A. This section as known as ” Enable Touchlink & GP mode”. B. Select this section and write it into the Zigbee NFC driver, the driver will enter Touchlink mode and GP Mode. Note: You can both have Touchlink and GP functions as long as you matched with Touchlink function first. C. Besides, you can re- power the device 4 times to enable this section as well.

4. A. This section as known as ” Enable Find&Bind / Delete GP “. B. Select this section and write it into the Zigbee NFC driver, the driver will enter Find&Bind mode,and it will delete previous GP bonding . C. Besides, you can re-power the device 3 times to enable this section as well.

With NFC Programming devices Note 1) Do wiring according to the wiring diagram . 2) Recommend setting parameters without power-on devices .
2) Please make sure your mobile phone has NFC function and enable it . Working with “SR NFC Tool” APP Step 1: Download the APP (searching “SR NFC Tool” from App Store and Google Playstore) .
Then open the APP .

1. Tap “+” to add devices.

Download “SR NFC Tool ”

2. Copy from a device.

Note: 1. Please Make sure that you have enabled NFC function with your mobile phone/ tablet . 2. Please Make sure that the “NFC position” is matched. 3. Please do not power on the device before setting. 4. If you can’t download “SR NFC Tool”. Please contact with us.
Step 2: Add device, and name it as you wish.

Step 3: Unlock device, enter parameters configuring page.

Locked

Unlock it

Note: 1. You have to unlock the device then do some settings 2. Only when the corresponding function is selected, the function interface will be displayed.
Step 4: Few parameter interface, you can choose the setting based on your requirements.

Target Current setting

Dimming Curve

Power-on state

Pairing

Fade time

Current Compensation

Step 5: After setting, please save the selected configuration via NFC and power on the device.

Tips
1. NFC function doesn’t require any power driver. 2. Many functions can be configured by NFC. Kindly check your desired functions. 3. You can create a default profile with the “+” button.

Wiring Diagram Application 1Without PUSH

LED OUTPUT

LED LN

INPUT

AC Push

–
Zigbee Dimmable Driver
ACL/ DC+ ACN/ DC-

Application 2With PUSH

LED OUTPUT

LED
AC PUSH SWITCH
LN

INPUT

AC Push

–
Zigbee Dimmable Driver
ACL/ DC+ ACN/ DC-

Product Dimension

Operating window

60

ULED (max), V

54

Output voltage [V]

45

36
ULED (min), V
27

18

9

0 0,10 0,30 0,50 0,70 0,90 1,10 1,30 1,50 1,70 Output current [A] Dimming Curve

Note: Test data under 1500mA gear
Driver Performance
Note: Test data under 1500mA gear

Driver Performance

Note: Test data under 1500mA gear
MCB Load Quantity

Module Number

Ipeak Twidth

Max.quantity of LED Driver per MCB

B10 B13 B16 B20 B25 C10 C13 C16 C20 C25 D10 D13 D16 D20 D25

SRP-ZG9105N-65CC500-1500 9.68A 70s 15 20 24 30 38 20 26 32 40 50 22 29 36 45 57

SRP-ZG9105N-65CCT500-1500 9.68A 70s 15 20 24 30 38 20 26 32 40 50 22 29 36 45 57

I (A) Ipeak ½ Ipeak
t

T (ms)

Note:
1.Those MCB parameters are based on ABB S200 series circuit breakers.
2.For different brands and models of miniature circuit breakers, the quantity of drivers will have difference.
3.Please do not exceed the above-mentioned quantity during on-site installation, and the specific load quantity shall be subject to on-site installation.
4.When the installation environment temperature of MCBs exceeds 30°C or when multiple MCBs are installed side by side, the number of mounted drives will be reduced, which requires recalculation.
5.Type C MCB’s are strongly recommended to use with LED lighting

Date 2023-9-28

Version V1.0

Update content Initial Version

Update by Romeo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>