KICHLER 52686BK Carston 2 Light Picture Light Instruction Manual
- June 1, 2024
- KICHLER
Table of Contents
Instruction Manual
FIXTURE DIAGRAM
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
PARTS LIST
PARTS LIST
[A] Shade
[B] Adjustment Screw ([C] Knob (2)| [D] Lock Washer (2)
[E] Canopy
[F] Mounting Screw (2)| [G] Mounting Plate
[H] Plate Mounting Screw (2)
[I] Outlet Box (not supplied)
---|---|---
CAUTIONS
CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fusebox before
starting and during the installation.
CAUTION:
- This fixture is intended for use with LED Bulb(s) ONLY.
WARNING:
- This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.
CLEANING:
- Always be certain that electric current is turned off before cleaning.
- Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.
INSTALLATION INSTRUCTIONS
-
Remove knobs[C] and lock washers[D] from the mounting screws that are preinstalled to mounting plate[G]. Retain knobs and lock washers.
-
Attach mounting plate[G] to outlet box[I] using the plate mounting screws[H]. Mounting plate can be adjusted to suit position of fixture.
NOTE: Mounting plate should be installed with the flat side of the mounting plate against the wall.
NOTE: Mounting plate should be installed with the bent flanges at the outer edge of the mounting plate pointing away from the wall, at the 12 and 6 o’clock position. -
Grounding instructions: (See Illus. a or b).
a. On fixtures where mounting plate is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting plate.
Fixture is provided with two (2) ground wires. Connect fixture ground wires to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
-
Make wire connections. Reference chart below for correct connections and wire accordingly.
Connect Black or Red
Supply Wire to:| Connect White Supply
Wire to:
---|---
Black| White
Parallel cord (round &
smooth)| Parallel cord (square &
ridged)
Clear, Brown, Gold or Black
without Tracer| Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor| Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)
-
NOTE: Fixture can be installed in the down position (light shines downward) or up position (light shines upward).
Push fixture to wall, carefully aligning the mounting screws protruding from the mounting plate with holes in canopy.
NOTE: Make sure all wires are inside canopy and do not get pinched between mounting plate and canopy, or wall and canopy of fixture. -
Slip lock washers[D] over threads protruding through holes in canopy (2 p laces).
-
Screw knobs[C] onto threads protruding through holes in canopy (2 places) and tighten to secure fixture to wall.
-
Adjust shade[A] (Fig. 1) by loosening the adjustment screws[B] at the fixture joints (turn slightly counterclockwise), adjusting shade to desired position, then re-tightening the adjustment screws (turn slightly clockwise). DO NOT COMPLETELY REMOVE THE ADJUSTMENT SCREWS FROM THE FIXTURE JOINTS.
-
Insert recommended LED bulb(s) (not included).
REV 21-OCT-2023
For warranty information please visit:
kichler.com/warranty
IS-52686-US
INSTRUCTIONS:
For Assembling and Installing
Fixtures in Canada
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>