YITAHOME ZSWYHS-V1 Farmhouse Ceiling Fan with Light and Remote Instruction Manual

: June 1, 2024
: YITAHOME

Table of Contents

ZSWYHS-V1 Farmhouse Ceiling Fan with Light and Remote
Specifications:
Product Usage Instructions:
Important Safety Instructions:
Before You Start:
Tools and Materials Required:
Installing the Fan:
FAQ:

ZSWYHS-V1 Farmhouse Ceiling Fan with Light and Remote

“`html

Specifications:

Model: ZSWYHS-V1
Type: Ceiling Fan
Power Source: Electric
Weight Capacity: At least 50 lbs
Control: Remote Control
Speed Settings: MED, LOW, HI
Timer Settings: 2H, 1H, 4H, 8H

Product Usage Instructions:

Important Safety Instructions:

Read all instructions and safety information before installing
the fan.
Disconnect power by removing fuses or turning off circuit
breakers before installation.
Ensure electrical connections comply with local laws and
codes.
Ensure sufficient room for fan blade rotation (at least seven
feet from floor to blade tips).
Use a metal outlet box securely attached to the building
structure for ceiling mounting.
If mounting on a joist, ensure it can support the fan’s
weight.
Secure all connections after installation to prevent
accidents.
Avoid inserting objects between fan blades while in
operation.
Wait for the fan to stop before changing its rotation
direction.
Avoid installing on sloped ceilings or using solid-state fan
speed control devices.

Before You Start:

Contact a licensed electrician if you are not experienced in
electrical work. Do not use a dimmer switch with the fan; turn off
power at the breaker.

Tools and Materials Required:

Phillips Screwdriver
Pliers
Straight Slot Screwdriver
Adjustable Wrench
Step Ladder
Wire Cutters

Installing the Fan:

Ensure there is 12″ (300mm) spacing from blade tips to nearest
objects or walls.
Turn off power before hanging the fan.
Follow the provided instruction manual for proper
installation.

FAQ:

Q: Can I install the fan on a sloped ceiling?

A: No, it is advised not to install the fan on a sloped ceiling
for safety reasons.

Q: What should I do if the fan blades are not rotating

properly?

A: Ensure that the blades are securely attached and there are no
obstructions hindering their movement. Check the installation
manual for troubleshooting tips.

Q: Can I use a solid-state fan speed control device with this

fan?

A: No, it is recommended not to use any solid-state fan speed
control devices with this fan to avoid electrical hazards.

“`

Pure & Easy

ZSWYHS-V1

ASSEMBLY INSTRUCTIONS
TLCFLS-2007

CONTACT US:
If you have any questions about the installation of YITAHOME® productsjust contact us at +1(888)-717-8084 from Mon-Fri 8:00 AM-16:30 PM PST / Saturday 8:00 AM-12:00 PMPST or E-mail us at: after-sale.cs@hotmail.com
Alternative method to contact us(amazon.com orders only) 1.Log into your amazon account 2.Go to “Your Orders” and find the purchase 3.Click on “Contact Seller”

CEILING FAN

ASSEMBLY INSTRUCTIONS

Important Safety Instructions
1.Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
2.Before installing the fan, disconnect the power by removing fuses or turning off circuit breakers.
3.Make sure all electrical connections comply with local law and the national electrical code. Please hire a qualified electrician or consult a do-it -yourself wiring handbook if you are unfamiliar with installing electrical wiring.
4.Make sure the installation site is roomy enough to allow fan blades to rotate. There is at least seven feet from the floor to fan blades’ tips.
5.If you are mounting the fan on a ceiling outlet box, please use a metal outlet box. Secure the box directly to the building structure. The outlet box and its support must be able to support the rotating fan (at least 50 lbs). Do not use a plastic outlet box. Attach the mounting bracket using the ceiling outlet box’s hardware.
6.lf you are mounting the fan on a joist, make sure it is strong enough to support the rotating fan (at least 50 lbs).
7.After installing the fan, make sure all the connections are secured so that the fan won’t fall.
8.Do not insert anything between fan blades while the fan is operating. 9.Turn the fan off and wait for it to stop before reversing fan’s rotating
direction. 10.To reduce the risk of electrical shock and personal injury, do not install
the fan on a sloped ceiling and do not use this fan with any solid-state fan speed control device, or rheostat. You must install the outlet box using the two steel screws and lock washers coming with the fan.
BEFORE YOU START
Contact a licensed electrician if you are not good at performing electrical work. It’s the licensed electrician who installs the fan, if required by the local code. Do not use the fan with a dimmer switch. Turn off power at breaker.
1

BEFORE YOU START
Contact a licensed electrician if you are not good at performing
OFF
electrical work. It’s the licensed OFF
electrician who installs the fan, if required by the local code. Do not use the fan with a dimmer switch. Turn off power at breaker.
Product Instruction

Tools and Materials Required

External Hexagonal Wire

Wrench

Stripper

Phillips Screw-

Step Ladder

Hanging Plate Main body

Blades

Fan Motor Assembly

Blade Bracket Screws for Blade Bracket Light Kit
Glass shade

Remote control

MED

LOW

LIGHT ON/OFF

HI

STOP

2H

1H

4H

8H

SCREWS BAG

Item no.

1 ×4

ST5x35 Setscrew

Item no.

2 ×2

Expansion Screw

3 ×4 Setscrew Stopper

4 ×3

Wire Cap

Item no.

5 ×2

8-32 Setscrew

6 ×2

Screw Washer

7

8

×2

×1

Screw Spring Washer

Balance Pack

9 ×16

Fabric Washer

10 ×16
Screws for Blades

2

ASSEMBLY INSTRUCTIONS
INSTALLING THE FAN
Tools Required: Phillips screwdriver, a pair of pliers, straight slot screwdriver, adjustable wrench, step ladder, and wire cutters.
INSTALLING THE MOUNTING BRACKET
The ceiling fan must be installed in the location where there is 12″(300mm) spacing from the tips of all blades to the nearest objects or walls. REMEMBER to turn off the power before hanging the fan. Follow the instruction below to hang your fan properly:
1. For concrete ceiling, drill two holes in the ceiling and secure the mounting bracket to the ceiling with two 0.32″(8mm) (distance between the two holes should be appropriate) expansion screws, flat washers nuts provided and tighten with a spanner.

ASSEMBLY INSTRUCTIONS
INSTALLING THE BLADE
1 )Attach blade brackets to blades with the blade bracket screws and metal or fabric washers.
2)Before installing fan blades, remove the motor’s fastener that is only used to protect the motor from damages in transit. Then, attach the blade assembly to the screws provided and tighten them.

2. For wood ceiling, secure the mounting bracket to the ceiling that is capable of carrying a load of at least 100lbs (45kgs) with two long mounting screws and washers provided. Be sure at least 0.12″(30mm) of the screw is threaded into the support.

3. For installing the outlet box, secure it directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully bear the moving weight of the fan (at least 100lbs). Use a UL listed metal outlet box instead of plastic ones. Figure 1& 2 show the examples of mounting the outlet box.

CEILING JOIST

PARALLEL WOOD BRACE (MIN.2″ THICK)

CROSS BRACE

OUTLET BOX

CELING JOIST

OUTLET BOX CEILING JOISTOR CROSS BRACE
3

INSTALLING THE FAN TO MOUNTING BRACKET ON CEILING
1.Securely attach the hanging bracket to the ceiling joist using the lag bolt, flat washers and spring washer supplied. (Figure 5)

Bracket Spring Washer
4

ASSEMBLY INSTRUCTIONS
MAKE THE ELECTRIC CONNECTIONS
To avoid possible electrical shock, make sure the electricity is turned off at the main fuse box before wiring.
1. Connect the fan to the remote control. The fan’s 4P plug should insert into the the remote control’s 4P plug.
2. Connect the remote control to the house’s power line, then connect the remote control’s white wire to the house’s white wire. Connect the remote control’s black wire to the house’s black wire, and connect all the fans’ green ground wires to the house of ground wires. Secure wires.
3. Connect the fan motor to the lamp: connect the fan motor’s 1P white wire to the lamp’s 1P white wire. Connect the fan motor’s 1P blue wire to the tool’s 1P blue wire.

ASSEMBLY INSTRUCTIONS
INSTALLING THE LIGHT KIT
1.Remove 3 mounting screws from the light kit. 2.Find the Molex connector from the motor and the Molex connector from the light kit. Slide
them together. 3.Install the motor’s junction box with 3 screws and tighten light kit. 4.Carefully install the glass shade into the main body and turn it clockwise to lock. WARNING: Take care not to over tighten when installing the glass shade.

1

2

to the FAN LIGHT

to AC Power

Motor

FOR LIGHT L

blue

FOR MOTOR/LIGHT N white

FOR MOTOR

black

green

4P
to the FAN MOTOR

4P

TO LIGHT L

blue

TO MOTOR/LIGHT N white

TO MOTOR

black

receiver of remote control

ACINL brown ACINN blue
green

ACL 120Vac ACN SUPPLY green

3

4

green

Installation is now finished. Turn on the power switch as Fig 7. Then the fan lights are on. Test and pair your fan

immediately using the remote control.

5

6

ASSEMBLY INSTRUCTIONS

OPERATING YOUR FAN
Turn on the power and check the operation of the fan: Kindly remind that the appropriate speed settings of warm or cool weather depend on many factors such as the room size, ceiling height, and the number of fans. The slide switch controls the direction of the blades: forward (switch down) or reverse (switch up).

REMOTE CONTROL SETTING AND OPERATION
1. Restore electricity to the outlet box by turning the electricity on at the main fuse box.
2. Remove the battery cover from the remote control transmitter, install the battery, and replace the cover.
Note: 1). Use a 12V battery to replace original one. 2). If not used for a long period of time, remove the battery to prevent damage to the remote transmitter, and store the remote transmitter away from excess heat or humidity.
3. Remote control’s functions are as follows, including controlling transmitter, fan speed and light.

(SUMMER TIME)
(WINTER TIME)
! NOTE:Wait for the fan to stop before reversing the direction of the blade rotation
A. Warm weather-(Forward) A downward airflow creates a cooling effect. This allows you to set your air conditioner on a higher setting without affecting your comfort.
B. Cool weather-(Reverse) An upward airflow moves warm air off the ceiling.This allows you to set heating unit on a lower setting without affecting your comfort.
7

MED

LOW

LIGHT ON/OFF

HI

STOP

2H

1H

4H

8H

LIGHT ON/OFF
Fan Speed H-Highest speed M-Medium speed L-Lowest speed
FANSTOP
Timer 1HFanantoturnoffafter1hour 2HFanautoturnoffafter2hours 4HFanautoturnoffafter4hours 8HFanautoturnoffafter8hours

8

ASSEMBLY INSTRUCTIONS

HOW TO USE BALANCING KITS
NOTE: CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE CEILING, IT WOULD CAUSE EXCESS VIBRATION, MOVEMENT OF A FEW CENTIMETERS IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEMS
TO REDUCE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURE THE MOUNTING BRACKET AND DOWNROD ARE SECURE
BALANCING A WOBBLING CEILING FAN For your convenience, a balancing kit is included: please follow this procedure when balancing the fan: 1.Check that all blades and blade arm screws are secure. 2.Most fan wobbling problems result from blade levels are unequal. Check this level by selecting a
point on the ceiling above one fan blade’s tip. Measure this distance. Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. The distance deviation should be equal within 1/8″ (0.32cm). 3.Use the enclosed blade balancing kit if the blade wobbling is still noticeable. 4.If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smooth operation.
! WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO NOT INSERT OBJECTS BETWEEN ROTATING FAN BLADES
NOISE It’s normal to hear small occasional noises when in quiet night or days. Please allow a 24-hour “breaking-in” period, most noises of a new fan disappear during the time.
MAINTENANCE AND CLEANING
1.Periodically cleaning your ceiling fan is the only required maintenance. Use a soft brush or lint free cloth to avoid scratching the paint. Please turn off the electricity power before you clean your fan.
2.Do not use water when cleaning your ceiling fan. It could damage the motor or the blades or even evoke an electrical shock.
3.The motor has permanently lubricated ball bearing. No need to oil NOTE: MAKE SURE THE POWER IS OFF IN THE ELECTRICAL PANEL BOX BEFORE
YOU DO ANY CLEANING OR REPAIRS
9

TROUBLESHOOTING
Your fan may occasionally jerk forward or backward upon starting up. This is normal and does not affect the fan operation. Try these troubleshooting steps before contacting customer service.

SYMPTOM

POSSIBLE SOLUTIONS

The fan doesn’t spin The fan’s light does not work

1. Make sure the fan is getting power. 2. Check the functionality of circuit breaker or fuse panel and wall switch. 3. Confirm fan wires are correctly connected to the house wires. 4. Make sure the blocker of the fan motor is removed. 5. Use your remote to check the power to the breaker and try to work your ceiling fan
manually from afar (Normal switch only for the fan power on/off)
Make sure the LED light kit and light bulb are connected well.

The fan is noisy and wobbling

1.Confirm the blade screws are NOT rubbing against the the motor’s round plastic part. 2.Confirm the pin wire are NOT connected against the moving part. 3. Confirm the coupling cover is NOT hitting the motor 4. Confirm the down rod is NOT slanted 5. Tighten any loose screws on the light kit, fan blades, motor coupling, down rod,
brackets and mounting hardware. 6. Confirm the hanger ball is firmly seated in the mounting bracket. 7. The ceiling beam must meet the minimum tensile test strength of 30KG for installation. 8. Make sure the airfoils and brackets are NOT bent or deformed. 9. Confirm the wire connections are not rattling against each other. 10. Confirm the fan blades are not cracked. If the fan blades are cracked, replace the
damaged blades with the set of new blades of same brand as your ceiling fan ensures the compatibility. 11. Change fan blades’ positions. 12. Confirm the light kit is NOT slanting and hitting the motor. 13. Confirm all the blades are screwed firmly into blade holders.

The fan or light automatically turns on/off

1.Confirm the circuit breaker is not malfunctioning. 2.Confirm the wire connections are not frayed. 3. Confirm the app does not set the timer or schedule 4. Power off the fan for 10 minutes, then power on again.

10