YITAHOME HZXY-V1 Pressure Washer Surface Cleaner Instruction Manual

YITAHOME HZXY-V1 Pressure Washer Surface Cleaner Instruction Manual

Imporant：

1. Keep your work area well lit to avoid accidents.
2. Keep children, bystanders, and pets away while using this cleaner and store it out of reach of children.
3. DO NOT operate this cleaner in cold conditions where the water supply might freeze or behave erratically.
4. DO NOT operate this cleaner near any power supply, electrical equipment, or objects such as glass that may shatter or cause injury when exposed to the pressurized spray.
5. DO NOT use this cleaner at pressures higher than 4000 psi (275 bars) or at feed rates greater than 4 gpm (15 L/min.)

Not Included but Necessary

1. Adjustable Wrench
2. M6 Hex Wrench
3. Pressure Washer with High-Pressure Hose and ⅜″ Quick Coupler
4. Silicone Oil

PRODUCT PARTS

1. Insert part C into part A, secure with 2 x part H and 2 x part G.
   

2. Attach part B to part C and secure with part H and part G.
   

3. Connect one end of part D to the control handle’s outlet on part B.
   

4. Connect the other end of part D to part E, then attach the connected parts D & E to part
   F. Finally link to part A, making sure all parts are closely connected during the process.
   

Maintenance

Nozzle

1. Over time, the nozzles may become obstructed from sediment, dust, or other debris. Check periodically and unclog using the provided cleaning pin (J) and clean water immediately.
2. If any nozzle is damaged, replace it with one of the provided spares (K). Apply some Teflon tape (I) to the thread of the replacement nozzle
   
   

Miscellaneous

1. Lubricate moving parts with high-quality silicone oil (not included) periodically.
2. The exterior of the cleaner can be cleaned with a soft damp cloth. DO NOT use abrasive cleaners or caustic chemicals.
3. If the cleaner won’t be used for an extended period of time, store in a cool and dry place that’s inaccessible to children and away from freezing temperatures.

Troubleshooting

ALWAYS cut off all power, drain all pressurized water, cool all heated surfaces, and disconnect the cleaner from your pressure washer and water supply before performing any adjustment, maintenance, or repairing of this device.

and water flow rate are no less than 2000 psi (137.5 bars) and 2 gpm (7.5 I./min.) respectively.
Excessive vibration| Clear off any obstructions in the slots of the nozzles with the cleaning pin.
Replace worn nozzles with the provided spares.
Retighten the bolts and nuts underneath the cleaner’ s main body with your adjustable wrench.
Water leaks| Retighten any loose connections.
Repair or replace any worn or damaged external parts, such as the high.pressure hos.
Non-rotation of the bar|

1. Unscrew the bolts on the hub of the main body using your M6 hex wrench and remove its housing.
2. Take out the swivel and replace any broken 0-rings with the provided spares (L) or correct their placement.
3. Install the swivel back into place and restore the hub.

CONTACT US:
If you have any questions about the installation of YITAHOME products, just contact us at +1 (888) 717 8084 from Mon-Fri 8:00 AM-4:30 PM PST/Sat. 8:00 AM-12:00 PM PST or e-mail us at aftersale.cs@hotmail.com

Alternative method to contact us (amazon.com orders only)

1. Log into your Amazon account
2. Go to “Your Orders” and find the purchase
3. Click on “Contact Seller”

References

• . Spend less. Smile more.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>