VEVOR HS-551 Train Horns Kit Instruction Manual
- June 1, 2024
- VEVOR
Table of Contents
VEVOR HS-551 Train Horns Kit
We continue to be committed to providing you tools with at competitive prices.
“Save Half”, “Half Price” or any other similar expressions used by us only
represent an estimate of savings you might benefit from buying certain tools
with us compared to major
top brands and do not necessarily mean to cover all categories of tools
offered by us. You are kindly reminded to verify carefully when you are
placing an order with us if you are saving half in comparison with the top
major brands.
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact
us: Technical Support and E-Warranty
Certificatewww.vevor.com/support
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again about any technology or software updates on our product.
PARAMETER LIST
PART LIST
SECURITY & WARNINGS
WARNING: Read the instructions before using this product. Failure to do
so can result in serious injury. Always observe the rules of safe operation.
- The temperature of the compressor may be very high during operation or after it has stopped, so do not touch it with bare skin.
- Install the system in a level, cool, dry place. Avoid hot and humid areas and do not wet the compressor motor.
- The speaker is very loud, so keep your ears away from the speaker to prevent damage to your ears.
- This product is not a toy. Do not allow children to play with or near this item.
ASSEMBLY PRECAUTIONS
- Assemble only according to these instructions. Improper assembly can create hazards.
- Wear ANSl-approved safety goggles and heavy-duty work gloves during assembly.
- Keep the assembly area clean and well-lit.
- Keep bystanders out of the area during assembly.
- Do not assemble when tired or when under the influence of alcohol, drugs, or medication
- Product capabilities apply to properly and completely assembled products only
- Assemble on a flat, level, hard, and smooth surface capable of safely supporting a fully loaded truck air horn. SAVE THESE INSTRUCTIONS
OPERATION
Step 1: Use a 10 mm open wrench or a 10 mm socket wrench to fix the compressor to the car using M6 bolts, four nuts, four flat washers, and four rubber cushion pads. Install the bolts through the gasket, compressor support, rubber washers, car frame, and nuts.
Step 2: Use a 10 mm open wrench or a 10 mm socket wrench to fix the horn
support to the horn and the car using four M6 bolts, four M6 nuts, and one
tripod. Install the bolts through the tripod – one end through the horn lock
nut, and the other end
through the car lock nut.
Model HS-660 Horn assembly
Step 1: Use a 10mm open wrench or a 10mm socket wrench to fix the two
horns to the support using four M6 bolts, four M6 nuts, four M6 gaskets, and
one tripod. Install the bolts through the tripod – through the horn, through
the gasket, and lock the nuts.
Model HS-660 Horn
Assembly Step 2 ：Insert the connectors of the two horns using the fitting
hose butt.
Step 3: Attach the coupling nut to both ends of the hose.
Step 4: Plug the hose into the connector (the hose will be easier to
install after heating)
Step 5: Use a 12 mm open-end wrench to tighten the air pipe nut.
Step 6: Use 16AWG and above copper wire to connect the horn line, the horn has two power lines (regardless of positive and negative terminals), one base iron (negative terminal), and the other one is connected to the positive terminal power supply after the horn switch.
Step 7: Use copper wire 14AWG, 20A power switch, 20A insurance, connect
the compressor line, the black line of the compressor to the iron (negative
electrode), and the red line is connected to the positive electrode of the
battery through the power switch.
- AIR HORN
- GAS POPE JOINT
- AIR HORN SOLENOID
- AIR TUBE
- AIR COMPRESSOR
- FUSE WIRE
- HORN BUTTON
- 8BATTERY IN THE VEHICLE
- PRESSURE METER
- PRESSURE SWITCH
- DRAIN VALVE
- POWER SWITCH
Troubleshooting
CORRECT DISPOSAL
This product is subject to the provision of the European Directive 2012/19/EU.
The symbol showing a wheelie bin crossed through indicates that the product
requires separate refuse collection in the European Union. This applies to the
product and all accessories are marked with this symbol. Products marked as
such may not be discarded with normal domestic waste but must be taken to a
collection point for recycling electrical and electronic devices.
Technical Support and E-Warranty Certificate
www.vevor.com/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>