WATTECO 50-70-166 Ventil’O Remote Supervision of Controlled Mechanical Ventilation System User Guide

June 3, 2024
WATTECO

ATTECO-LOGO

WATTECO 50-70-166 Ventil O Remote Supervision of Controlled Mechanical

Ventilation

ATTECO-50-70-166 Ventil’O-Remote-Supervision-of-Controlled-Mechanical-
Ventilation-System-PRODUCT-IMAGE

Start

ON :

ATTECO-50-70-166 Ventil’O-Remote-Supervision-of-Controlled-Mechanical-
Ventilation-System-02

OFF :

ATTECO-50-70-166 Ventil’O-Remote-Supervision-of-Controlled-Mechanical-
Ventilation-System-03

Connectors

Characteristics:

  • Impedance: 1MΩ
  • Tension : 0-30Vcc
  • Courant  Delivered current: 3.5 µAFréquence signal max / Signal frequency max: 0-100 Hz

Wiring to open collector output

Wiring to isolated dry contact output

Status report or pulse count (if provided)
Use a flexible cable with a sheath with a diameter between 2.5mm and 6.5mm and single-stranded (or multi-stranded with crimp) 20-26AWG wires.

  1. Hold the base of the cable gland and slightly loosen the nut
  2. Thread the cable, taking care not to damage the seal
  3.  Strip the cable for about 10cm. Adjust the cable and retighten the nut.

Strip each strand to a length of 5-6mm and connect as below:

ATTECO-50-70-166 Ventil’O-Remote-Supervision-of-Controlled-Mechanical-
Ventilation-System-07

Installation

Setting up

Opening  Closure  les 4 vis un ¼ de tour Unscrew the 4 screws by ¼ turn

Montage mural
Wall mounting

ATTECO-50-70-166 Ventil’O-Remote-Supervision-of-Controlled-Mechanical-
Ventilation-System-08

  • Place the dowels and screw the housing to the wall
  • Drill the duct to 8mm diameter
  • Insert the air intake into the duct on the airflow side
  •  Fix the air intake to the duct with the 2 self-tapping screws provided
  •  Connect the flexible tube to the air intake by fitting it as tightly as possible

ATTECO-50

Orientation des tubes
Tube orientation

ATTECO-50-70-166 Ventil’O-Remote-Supervision-of-Controlled-Mechanical-
Ventilation-System-10

For the sensor to work properly, it is necessary to avoid fogging of the pipes.

 Radio propagation

Check the radio coverage with the Netw’O.

For the sensor communicates correctly, the number of obstacles should be limited to avoid excessive radio attenuation.

Characteristics

Reference| __

50-70-101

| __

50-70-166

---|---|---
Class| A| A
Power Level| +14 dBm| +14 dBm
Measure :

de pression en 2 points

The pressure difference at 2 points

Entrée S0 / Input S0

| ✓| ✓

__

Antenna

| Interne

Internal

| Interne

Internal

__

Casing materials

| ASA / PC| ASA / PC
__

Indicede protection

IP rating

| IP65| IP65

ATTECO-50-70-166 Ventil’O-Remote-Supervision-of-Controlled-Mechanical-
Ventilation-System-13Watteco represented by JC LE BLEIS, declares that the radio equipment type 50-70-166 / 50-70-101 is in conformity with Directive 2014/53/EU (RED) and UKCA. The full text of the EU and UKCA Declaration of Conformity is available at the following web address: https://www.watteco.com/assistance/download-center/

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

WATTECO User Manuals

Related Manuals