KICHLER 39456A Outdoor Wall Lantern Instruction Manual
- June 12, 2024
- KICHLER
Table of Contents
KICHLER 39456A Outdoor Wall Lantern
Product Information
- Product Name: Outdoor Wall Lantern
- Model Number: 39456A
- Item Number: 0616264, 31885177
- Manufacturer: Kichler
Package Contents
| Part | Description | Quantity |
|---|---|---|
| A | Canopy | 1 |
| B | Mounting Bracket | 1 |
| C | Socket | 1 |
| D | Decorative Scroll | 1 |
| E | Fixture Top | 1 |
Hardware Contents
| Part | Description | Quantity |
|---|---|---|
| AA | Wire Connector | 3 |
| BB | Short Machine Screw | 2 |
| CC | Threaded Knob | 2 |
| DD | Long Machine Screw | 2 |
| EE | Decorative Scroll Screw | 2 |
Safety Information
Please read and understand this entire manual before attempting to
assemble, operate, or install the product. This product contains chemicals,
including lead, which is known to the State of California to cause cancer,
birth defects, or other reproductive harm. For more information, visit
http://www.P65Warnings.ca.gov. Do not leave out parts or use any parts that
are worn out or broken. Failure to follow these instructions may invalidate
the ETL listing and/or C.S.A. certification of this fixture.
Product Usage Instructions
Preparation
Before beginning the assembly of the product, ensure that all parts are
present. Compare the parts with the package contents list and hardware
contents list. If any part is missing or damaged, do not attempt to assemble
the product. Estimated Assembly Time: 30 minutes to 1 hour
Tools Required for Assembly (not included)
- Phillips screwdriver
- Flathead screwdriver
- Wire strippers
- Electrical tape
- Ladder
- Safety glasses
Assembly Instructions
Step 1: Orient the mounting bracket (B) so the raised center portion
protrudes into the outlet box (not included). Insert long machine screws (DD)
through the mounting bracket (B) so that the long machine screws (DD) protrude
outward. Connect the mounting bracket (B) to the outlet box with short machine
screws (BB).
Step 2: Place the front end of the decorative scroll (D) under the fixture top (E). Line up the hole on the decorative scroll (D) and canopy (A). Screw the decorative scroll screw (EE) through the decorative scroll (D) and into the canopy (A).
Step 3: Connect the wires using wire connectors (AA) as follows:
- Bare Copper or Green Ground Supply Wire
- Black Supply Wire
- White Supply Wire
- Black Supply Wire
- White Supply Wire
Step 4: The mounting surface should be clean, dry, flat, and 1/4 in. larger than the canopy (A) on all sides. Any gaps between the mounting surface and canopy (A) exceeding 3/16 in. should be corrected as required with silicone caulking compound. Caulk completely around where the back of canopy (A) meets the wall surface to prevent water from seeping into the outlet box.
Step 5: Pass the canopy (A) over the long machine screws (DD) protruding from the mounting bracket (B) and secure it in place with threaded knobs (CC).
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Canopy | 1 |
| B | Mounting Bracket | 1 |
| C | Socket | 1 |
| D | Decorative Scroll | 1 |
| E | Fixture Top | 1 |
HARDWARE CONTENTS
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble,
operate or install the product.
WARNING
CAUTION – RISK OF SHOCK
Disconnect Power at the main circuit breaker panel or main fusebox before
starting and during the installation.
WARNING
This fixture is intended for installation in accordance with the National
Electrical Code (NEC) and all local code specifications. If you are not
familiar with code requirements, installation by a certified electrician is
recommended.
- Do not use bulbs with wattage greater than specified on this fixture.
- California Proposition 65
WARNING : This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to http://www.P65Warnings.ca.gov
CAUTION
- If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate the ETL listing and/or C.S.A. certification of this fixture.
PREPARATION
Before beginning assembly of the product, make sure all parts are present.
Compare parts with the package contents list and hardware contents list. If
any part is missing or damaged, do not attempt to assemble the product.
Estimated assembly time: 30 minutes to 1 hour Tools Required for Assembly (not
included): Phillips screwdriver, flathead screwdriver, wire strippers,
electrical tape, ladder, and safety glasses.
ASSEMBLY INSTRUCTIONS
Orient the mounting bracket (B) so the raised center portion protrudes into the outlet box (not included). Insert long machine screws (DD) through mounting brackets (B) so the long machine screws (DD) protrude outward. Connect the mounting bracket (B) to the outlet box with short machine screws (BB).
Hardware Used
Place the front end of the decorative scroll (D) under the fixture top (E). Line up the hole on the decorative scroll (D) and canopy (A). Screw the decorative scroll screw (EE) through the decorative scroll (D) and into the canopy (A).
Hardware Used
Wire connection guide:
Ground wire:
- For installation in the United States: Wrap ground wire from the outlet box around the ground screw on mounting bracket (B) no less than 2 in. from the wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect to the outlet ground wire with a wire connector (AA).
- For installation in Canada: If the fixture is supplied with ground wire, wrap ground wire around the ground screw on the mounting bracket (B). Tighten the ground screw. Connect the fixture ground wire to the outlet ground wire with the wire connector (AA). Supply wires:
- Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord “D” shaped and ribbed).
- Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth).
NOTE:
Fixture wires will either be:
- Black and White.
- Parallel Cord SPT-1 lamp wire with one round smooth wire and one “D” shaped ribbed wire.
The mounting surface should be clean, dry, flat, and 1/4 in. larger than the canopy (A) on all sides. Any gaps between the mounting surface and canopy (A) exceeding 3/16 in. should be corrected as required with silicone caulking compound. Caulk completely around where the back of canopy (A) meets the wall surface to prevent water from seeping into the outlet box. Pass the canopy (A) over the long machine screws (DD) protruding from the mounting bracket (B) and secure in place with threaded knobs (CC).
Hardware Used
****Insert 60-watt max. medium base bulb or LED equivalent (not included) into the socket (C).
CARE AND MAINTENANCE
- Always be certain that the electric current is turned off before cleaning this item.
- Use a soft, moist cloth with mild non-abrasive soap to clean the fixture. Never use glass cleaner on fixtures, as it will damage the metal finish.
- All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher.
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| Fixture does not light. | 1. Fixture may be wired incorrectly. |
2. Worn or broken bulb.
| 1. Check wiring.
2. Replace the bulb.
Distribuido por: Kichler Lighting LLC 30455 Solon Rd Solon, OH 44139 Impreso en China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>