VIDEOTEC UPTBVTR ULISSE2 Housing Upper Part with Anti-Ice Glass and Wiper Instruction Manual

VIDEOTEC UPTBVTR ULISSE2 Housing Upper Part with Anti-Ice Glass and Wiper

About this manual

Read all the documentation supplied carefully before installing and using this unit. Keep the manual in a convenient place for future reference.

Typographical conventions

CAUTION!
Medium level hazard.
This operation is very important for the system to function properly. Please read the procedure described very carefully and carry it out as instructed.

INFO
Description of system specifications.
We recommend reading this part carefully in order to understand the subsequent stages.

Notes on copyright and information on trademarks

The quoted names of products or companies are trademarks or registered trademarks.

Safety rules

CAUTION! Device installation and maintaining must be performed by specialist technical staff only.

• The manufacturer declines all responsibility
  for any damage caused by an improper use
  of the appliances mentioned in this manual. Furthermore, the manufacturer reserves the right to modify its contents without any prior notice. The documentation contained in this manual has been collected with great care. The manufacturer, however, cannot take any liability for its use. The same thing can be said for any person or company involved in the creation and production of this manual.

• Never, under any circumstances, make any changes or connections that are not shown in this handbook. Improper use of the appliance can cause serious hazards, risking the safety of personnel and of the installation.

• Use only original spare parts. Non-original spare parts could cause fire, electrical discharge or other hazards.

• Before proceeding with installation, check the supplied material to make sure it corresponds to the order specification by examining the identification labels (4.2 Product marking, page 2).

Identification

Product description and type designation
ULISSE2 housing upper part with anti-ice glass and wiper

Product marking
See the label attached to the product.

Preparing the product for use

Any change that is not expressly approved by the manufacturer will invalidate the guarantee.

Unpacking
When the product is delivered, make sure that the package is intact and that there are no signs that it has been dropped or scratched.
If there are obvious signs of damage, contact the supplier immediately. Keep the packaging in case you need to send the product for repairs.

Contents
Check the contents to make sure they correspond with the list of materials as below:

• Upper body of the housing
• Instruction manual

Safely disposing of packaging material
The packaging material can all be recycled. The installer technician will be responsible for separating the material for disposal, and in any case for compliance with the legislation in force where the device is to be used. When returning a faulty product we recommend using the original packaging for shipping

Product Overview

1. Wiper
2. Heated glass control board
3. Wiper connector
4. Heated glass connector

Installation

This product can only be installed on the ULISSE2 line Pan & Tilt. For installation and setting please refer to the P&T manual.

Disposal of waste materials

This symbol mark and recycle system are applied only to EU countries and not applied to the countries in the other area of the world.

• Your product is designed and manufactured with high quality materials and components which can be recycled and reused.
• This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste.
• Please dispose of this equipment at your local Community waste collection or Recycling centre.
• In the European Union there are separate collection systems for used electrical and electronic products.

Technical data

• General
  • Die cast aluminum body.
  • Epoxypolyester powder painting, RAL9002 colour.
• Mechanical
  • Dimensions: 18.8×12.2×47.3cm
  • Unit weight: 2.3Kg
• Environment
  • Outdoor/Indoor
  • Operating temperature: from -40°C (-40°F) up to +65°C (149°F)
• Certifications
  • UR certification
  • EAC certification

Technical drawings

The dimensions of the drawings are in millimetres.

Headquarters Italy Videotec s.r.l.
Via Friuli, 6 – I-36015 Schio (VI) – Italy
Tel. +39 0445 697411 – Fax +39 0445 697414 Email: info@videotec.com

References

• Video Security Products | Videotec

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>