KICHLER 52719BK Madden 6 Light Taper Candle Style Chandelier Instruction Manual

June 1, 2024
KICHLER

KICHLER 52719BK Madden 6 Light Taper Candle Style Chandelier

KICHLER 52719BK Madden 6 Light Taper Candle Style
Chandelier

FIXTURE DIAGRAM

Fixture Diagram

PARTS LIST

[ A ] Outlet Box (Not Supplied)
[ B ] Strap Mounting Screw (2)
[ C ] Mounting Strap
[ D ] Mounting Screw (2)
[ E ] Canopy
[ F ] Knob (2)
[ G ] Lock Washer (2)
[ H ] Main Body
[ I ] Decorative Tube
[ J ] Stems (2-12”, 1-6” with Short Threaded Tubes installed, 1-6” installed to Round Coupling)
[ K ] Loop
[ L ] Socket
[ M ] Round Coupling (with Stem and Short Threaded Tube installed)
[ N ] Short Threaded Tubes
[ O ] Chain Link
[ P ] Long Threaded Tube
[ Q ] Coupling

CAUTIONS

CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fuse box before starting and during the installation.

WARNING:

  1. This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
    Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

  • Always be certain that electric current is turned off before cleaning.
  • Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

FIXTURE DIAGRAM INSTALLATION INSTRUCTIONS

NOTE: Thread locking compound must be applied to threads as noted with (▶) symbol to prevent accidental rotation of fixture during cleaning, relamping, etc.

  1. Find the appropriate threaded holes on mounting strap[C] that align with hole distance in canopy[E]. Assemble mounting screws[D] into threaded holes starting from the outlet box side.

  2. Attach mounting strap to outlet box[A] using the supplied strap mounting screws[B]. Mounting strap can be adjusted to suit position of fixture.

  3. Rotate fixture arms up 90 degrees into position as shown (Fig. 1).
    NOTE: Sockets[L] should all face upward when in final position.
    Fixture Diagram Installation Instructions

  4. Screw long threaded tube[ P ] into coupling[ Q ] (on main body[ H ]).
    NOTE: Long threaded tube should be screwed into coupling completely, and hex nut near the end of long threaded tube should be snug against the coupling.

  5. Lower decorative tube[ I ] down over long threaded tube, carefully passing threads on end of long threaded tube[P] through hole in top of decorative tube. Carefully seat decorative tube on top of fixture.

  6. Screw round coupling[ M ] onto threads protruding from top of decorative tube. Tighten round coupling to secure decorative tube in place.
    NOTE: The 6-inch stem that is preinstalled to the round coupling must be used when mounting the fixture. The 6-inch stem that is preinstalled to the round coupling should NOT be removed from the round coupling.

  7. Pass fixture wires through desired number of additional short threaded tubes[ N ] and stems[ J ].
    Screw stems together using short threaded tubes.

  8. Pass fixture wires from last stem through loop[ K ]. Screw loop onto end of last stem.

  9. Connect loop on end of stem(s) to loop attached to bottom of canopy with chain link[ O ]. Close the open chain link by placing a piece of cloth over the link and using a pair of pliers to gently squeeze the link closed.

  10. Pass fixture wires through loop (attached to bottom of canopy), and into canopy.

  11. Cut fixture wires a MINIMUM of 6 inches from the top edge of canopy.

  12. Grounding instructions: (See Illus. a or b).
    a. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
    b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
    If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
    Fixture Diagram Installation Instructions

  13. Make wire connections. Reference chart below for correct connections and wire accordingly.
    Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
    ---|---
    Black| White
    Parallel cord (round & smooth)| Parallel cord (square & ridged)
    Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
    Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
    *Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)| Fixture Diagram Installation
Instructions

  14. Raise canopy to ceiling, carefully passing mounting screws through mounting screw holes in canopy.
    NOTE: Be certain wires do not get pinched between mounting strap and canopy or canopy and ceiling.

  15. While holding canopy in place, use lock washers[ G ] and knobs[ F ] to secure canopy. Tighten to secure.

  16. Insert recommended bulbs. (Not supplied).

CUSTOMER SUPPORT

© 2024 Kahler Lighting LLC. Toups droits reserves
Pour de plus amplest informations sur la guarantee, veiled visited : kichler.com/warranty
IS-52717-CB
REV 16-JAN-2024 Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

KICHLER User Manuals

Related Manuals