VEVOR AX-SDD-001 12V LED Pool Light Instruction Manual
- June 1, 2024
- VEVOR
Table of Contents
Technical Support and E-Warranty Certificate
www.vevor.com/support
LED Pool Lights
MODEL: AX-SDD-001 / AX-SDD-002 / AX-SDD-003 / AX-SDD-004
We continue to be committed to provide you tools with competitive price. “Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.
AX-SDD-001 / AX-SDD-002
AX-SDD-003 / AX-SDD-004
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us:
Technical Support and E-Warranty Certificate
www.vevor.com/support
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
| Warning-To reduce the risk of injury, user must read instructions manual
carefully.
---|---
| This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) This device may not cause harmful
interference, and (2)this device must accept any interference received,
including interference that may cause undesired operation.
- Make sure the electricity is off before installing the fixture.
- The circuit connection must be correct before connecting the wire.
- Don’t worry about the heat on the surface of the lamp when it’s working. It’s a normal situation.
- The lifespan will be shorter and the light attenuation will be faster if the lamp works for 24 hours every day.
- Make sure output voltage is within the range of rated voltage before installing the lamp.
If the lamp doesn’t work, don’t inspect it when power is on. The lamp should be inspected and maintained by professional electrician.
FUNCTION INTRODUCTION
- Easy installation
- 12color modes
- High brightness
- Low power consumption
- Can be widely used in swimming pool, bathroom, fountain, etc
- Stainless steel housing
- High quality LED light source, life time more than 30000 hours
- The lamp is potting protected by epoxy resin + sealed silica gel, and the waterproof grade is above IP68
RELEVANT PARAMETERS
- Working Voltage: DC12v
- Working Temperature: – 35°C To 55°C
- Protection Level: IP68
- Input Power: 40W
- Control Mode: Wireless Remote Control, Multiple Modes Optional, Speed Adjustable
MODE
- Mode 1: Steady red
- Mode 2: Steady green
- Mode 3: Steady blue
- Mode 4: Steady Yellow
- Mode 5: Steady purple
- Mode 6: Steady Cyan
- Mode 7: Steady White
- Mode 8: Red, green and blue flicker change
- Mode 9: Colorful flicker change
- Mode 10:Red, green and blue gradient
- Mode 11: Colorful gradient
- Mode 12: Steady Black
OPERATION INSTRUCTIONS
- Install lamps, controllers and power supplies in appropriate areas, and protect exposed wires
- Ensure that the power supply output voltage conforms to the luminaire parameters
- Connect the power supply, lamps and controllers according to the requirements marked on the lamps and the color of the wires
- After the installation of the line to check the correct, turn on the power to use
PRECAUTIONS
- Before powering on, make sure all wiring is correct and the wires are not broken
CAUTION
| • The power lead of the lamp is adjusted according to the design
requirements, and the voltage, current and all parameters are in the best
state. It is necessary for the user to select a cable diameter thicker than
the dominant cable when extending the dominant cable. However, it is
prohibited to cut the cable.
---|---
CAUTION| • When the underwater light is lit, it must be placed in the
water, otherwise it will affect the life of the lamp, and even burn the entire
product.
- Power supply and controller can not be used in water.
Place the lamp body in a fixed installation position, fix it with screws, and pull the wire to the ground where there is no water.
Connect the lamp line to the output of the controller.
Connect the output of the 12V constant voltage power supply to the input of the controller
Make sure that the lamp and controller, switch power supply wiring is correct, plug into 120V socket
About the remote control
The factory remote control and the receiver have been paired. If accidentally
deleted, you can pair by the following method
Pairing ID: Press the receiver M4-3A learning key, the running light becomes
steady on, and then press M4 Remote control any button, the running light
flashes a few times, and the pairing success
Delete ID: Press and hold the receiver M4-3A learning key for 5 seconds to
delete successfully
-
Speed/brightness +
-
Speed/brightness –
-
Color ring
-
Mode
-
White light switch/ brightness key
-
Switch
-
Power indicator light
-
Operating lamp
-
Remote ID learning key
-
DC Power Jack
-
12 to 24Vdc power input
-
connection terminal
LED pool light wiring diagram
- Neutral
- Line
- SWITCH
- Ground
- Red
- Green
- Blue
- White
- Brown (Firewire)
LED Pool Light Installation Layout
- Pool Light Transformet
- GFCI
- 120 VAC SUPPLY
- LED driver and controller
- Rigid Conduit
- 8″min Control Box, to max water level or the pool
- 18″min.to top of lens
- Coil 4 ft. of light cable around Fixture
Power Supply Structure Diagram
Model : LPV-60-12
Input : AC100-240V 1.2A
Authentication: UL,CE,UKCA
Sanven Technology Ltd.
Address: Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
Made In China
Technical Support and E-Warranty Certificate
www.vevor.com/support
Documents / Resources
|
VEVOR AX-SDD-001 12V LED Pool
Light
[pdf] Instruction Manual
AX-SDD-001, AX-SDD-002, AX-SDD-003, AX-SDD-004, AX-SDD-001 12V LED Pool Light,
AX-SDD-001, 12V LED Pool Light, LED Pool Light, Pool Light, Light
---|---