American Products AM47F-6042-48RU AP Freedom Multi Bay Enclosure Owner’s Manual
- June 13, 2024
- AMERICAN PRODUCTS
Table of Contents
AP FREEDOM™
Multibay Telecommunications Enclosure
Owner’s Manual
Contacting Us
American Products can be contacted for any issues that arise with the supplied
product.
Technical assistance is available 9am to 4pm central standard time.
- Toll Free: 855-736-2135
- Phone: 417-736-2135
- Fax: 417-736-9535
- Email: Sales@amprod.us
- Web: www.amprod.us
When calling, please have available, or if faxing or emailing, be sure to provide:
- Part Number
- Serial Number
- Date of Purchase
- Date of Installation
Safety First
This publication provides a description of the American Products AP FREEDOM™
Multibay Enclosure. The mechanical descriptions, typical applications,
installation instructions, safety guidelines and grounding are included.
Four types of messages may appear throughout this manual, identified by the
following icons and signal words:
Read equipment manufacturer’s manual and this material before using this
product. Failure to do so can result in serious injury or death.
DANGER| Indicates a hazardous situation that, if not avoided, will result
in death or serious injury. This signal word is to be limited to the most
extreme situations.
---|---
WARNING| Indicates a hazardous situation that, if not avoided, could
result in death or serious injury.
CAUTION| Indicates a hazardous situation that, if not avoided, could
result in minor or moderate injury.
NOTICE:| Indicates information considered important, but not hazard
related (e.g. messages relating to property damage). The safety alert symbol
shall not be used with this signal word. When a signal word is used for
messages relating to property damage, NOTICE is the choice of signal word.
Important Labeling Information
AP
FREEDOM™ Multibay Enclosure for Type 4 Powder Coating Tested to Standards:
Telcordia GR487 for Telecommunications Enclosures
Product Overview
- The cabinet is constructed of Aluminum and Stainless Steel with powder coat painted finish for reduced weight and superior corrosion resistance. The front doors are equipped with three point pad-lockable door latches. The top of the cabinet has a double wall construction to reduce the effects of solar radiation and for structural integrity.
- The equipment-mounting bay has 19” Rack Rails and 24 RUs of space in each bay.
- The cabinet utilizes stainless steel hardware, UL recognized EPDM edge gasketing (temp range of – 40F to +212 F.
- When installing cabling or equipment that enters the cabinet, Type 4 entrances, fittings or equipment is to be used to maintain the integrity of the enclosure
- No live equipment or components are to be installed below the lowest RU rack mounting provision or on the floor of the enclosure with the exception of batteries.
Product Measurements
AP FREEDOM™ Multibay Enclosure for Type 4
**Quarter Turn 3-Point Locking Door Latches
**
The cabinet doors are equipped with quarter-turn 3-point padlock-able door
latches. The latches are secured by turning the handle a quarter turn
clockwise until the stop is reached.
Convenient security padlock hole to allow for a standard Master lock (or
equivalent) to be installed. With a padlock on the latch, access door cannot
be opened protecting the cabinet from undesired intrusion.
Clearance Requirements
When selecting a location to mount the cabinet, ensure that proper clearance
is available to allow the cabinet door to open fully.
See Figure below for top view of cabinet footprint.
Lifting Provisions
Constructing a New Pad
- Use only concrete for new pad construction. Do not use substitute materials since they lack the rigidity for enclosure placement.
- Observe local building practices for pad construction. American Products recommends that the pad should extend a minimum of 8” beyond the enclosure base on all sides.
- Use a minimum of 6” of sand or gravel as a base for the pad for leveling purposes.
WARNING| When pad mounting, the compression strength of the pad must be
at least 4000 psi as determined by ASTM C39 test of compression strength of
concrete cylinders. The slump of the concrete shall be 2” to 4” as determined
by ASTM C143 test method.
---|---
Grounding
Bonding and grounding should be done in accordance with industry standard procedures and comply with applicable electrical codes and local jurisdictions.
Appendix A
Technical Support
American Products can be contacted for any issues that arise with the supplied
product.
Technical assistance is available 9am to 4pm central standard time.
-
Toll Free: 855-736-2135
-
Phone: 417-736-2135
-
Fax: 417-736-9535
-
Email: Sales@amprod.us
-
Web: www.amprod.us
When calling, please have available, or if faxing or emailing, be sure to provide: -
Part Number
-
Serial Number
-
Date of Purchase
-
Date of Installation
Warranty Policy
Enclosures designed and manufactured by American Products shall be warranted
to be free of defects in material or workmanship for a period of 5 years (U.S.
& Canada) and 3 years for International deployments from the date of shipment.
Should the product be proven to be defective, American Products will have the
option to repair or replace the product. Items included with the enclosures,
not manufactured by American Products, will carry the original manufacturer’s
warranty.
It is the responsibility of the buyer to communicate any special environmental
concerns in which the enclosures will be utilized. Special materials may be
required to allow for proper corrosion resistance for harsh environments. The
warranty does not cover enclosures used in applications and environments for
which they were not designed. Warranty does not cover abuse, modifications by
others or reimbursement for unauthorized rework. At no time will American
Products reimburse purchaser for unauthorized rework on any product.
Under no circumstances is American Products liable for any consequential
damages, liquidated damages, loss in profits or revenues, costs of capital,
downtime costs or damages related to our product performance.
Warranty Claims
Enclosures found to be defective will be repaired or replaced with the same or
comparable product.
All warranty claims must be communicated to our customer service
855-736-2135 department to obtain an
RMA number. For warranty claims in the USA and Canada, freight will be managed
and paid by American Products. For warranty claims outside of the USA and
Canada, the customer will be responsible for managing the freight and freight
expenses. Products being returned from other than US or Canada are to be
returned to the factory in Strafford, MO to receive warranty resolution, once
approved with an RMA.
Except for the express warranty stated above, American Products makes no other
warranties with respect to the product, expressed or implied, including but
not limited to merchantability or fitness for a particular purpose.
597 Evergreen Road Strafford, Missouri 65757
Phone: 417-736-2135 Toll Free:
855-736-2135
www.amprod.us
Form 36-0061-10
Updated: 04/27/2022
597 Evergreen Road
Strafford MO 65757
417-736-2135
Toll Free: 855-736-2135
Web: www.amprod.us
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>