COLAMY A231 Button Tufted Dining Chairs Set Instruction Manual
- June 14, 2024
- COLAMY
Table of Contents
**COLAMY A231 Button Tufted Dining Chairs Set Instruction Manual
**
WARNING
Please read the instructions carefully and follow the assembly steps
To ensure proper assembly, please follow all steps and use all parts provided.
Not following this warning may result in serious injury to you or others.
To prevent misalignments, keep the screws loose and do not tighten them until
they are all in their correct positions.
Avoid overtightening or forcing the screws, as this could cause them to break,
strip, or damage the threads of the holes.
Using the wrong size of screws for a particular part could cause damage to the
screw or the part.
Please lubricate all moving parts regularly and tighten all bolts and screws
every 6 months, or as needed.
PRODUCT DETAILS
They provide greater stability and prevent the floor from scratching, keeping the chair stable at all times.
High Elastic Spring
This design offers great support and comfort, protecting the chair from slipping
SAFETY INFORMATION
WEIGHT CAPACITY FOR SEATING: 250LBS
Sit in the center of the chair with your back against the backrest
Do not sit at the front edge of the chair
Do not push the chair around when a person is sitting in it
Do not stand on the chair
Do not push down on the backrest when a person is reclined
Do not use the chair with more than one person
Do not place all your weight on the backrest only
ASSEMBLY PARTS AND TOOL
**BEFORE YOU GET STARTED, A FEW POINTERS:
** Please open the Seat Cushion bottom and take out all accessories before installation.
Please use the included wrench instead of an ELECTRIC HAND DRILL in case of damage to the chair leg.
*Seat Bottom 1
Back Legs Marked B 2
Front Legs Marked F 2
Bolt M860mm 8
Spring Washer *8
Flat Washer *8
Wrench *1
PLEASE MAKE SURE ALL THE PARTS ARE INCLUDED. MISSING PARTS?
support@colamyhome.com
**
ASSEMBLY INSTRUCTIONS
Connect 2 Front Legs Marked F (3) to Seat Bottom (1) by using
Spring Washer (B), Flat Washer (C), Bolt M8*60mm(A) and Wrench
(D), please tighten the bolts 50% at first.
Note: The side where the black tape is applied is the side where the
screws are tightened.
Step 1
Bolt M860mm 4
Spring Washer *4
Flat Washer *4
Wrench *1
Step 2
Connect 2 Back Legs Marked B( 2 ) to Seat Bottom (1) by using Spring
Washer (B), Flat Washer( C), Bolt M8*60mm (A) and Wrench (D),
please tighten the bolts 50% at first.
Note : The side where the black tape is applied is the side where the
screws are tightened.
*Bolt M860mm *4
Spring Washer *4
Flat Washer *4
Wrench *
**
Step 3
Now, Adjust the balance of the whole chair and tighten all bolts to 100%, by
using the Wrench(D).
ATTENTION
Please read the following instructions to help you assemble the dining
chair faster.
Step 1
Partly screw in bolts, but do not fully tighten.
Step 2
Put pressure on the seat. (About 44lbs/20kg)
Place the chair on a flat surface and apply pressure to the seat. Firstly
tighten the middle bolt on the back, then both bolts on the sides, and finally
the front legs. Make sure all bolts are fully tightened before using the
chair.
**Step 3
** lf the legs are uneven, you can also adjust the foot pegs at the bottom of the legs to improve balance.
LIMITED WARRANTY
COLAMY promises to repair or replace any COLAMY chair that is found to be
defective in material or workmanship within one year from the date of original
purchase so long as you, the original purchaser, still owns it. This is your
sole and exclusive remedy. This warranty is subject to the provisions below.
EXCLUSIONS
This warranty does not apply and no other warranty applies to:
- Normal wear and tear, which are to be expected over the course of ownership.
- Misuse, abuse, or excessive use of the product.
- Modifications or attachments to the product that are not approved by COLAMY.
- Products that were not installed, used, or maintained in accordance with product instructions and warnings.
- Products used for rental purposes or unauthorized retail activities.Seating Usage: Normal use for seating is identified as the equivalent of a single shift, forty- (40) hour workweek. To the extent that a seating product is used in a manner exceeding this, the applicable warranty period will be reduced in a pro-rata manner. We adopt a 30-day return policy which means that all products purchased on this website may be returned to us within the timeframe. You need to contact us within 30 days after the product(s) came into your possession andthe product(s) must be returned to us without any undue delays.
RETURN POLICY
Returned products must be returned in the same condition as they were sent and they must be sent in their original packaging.
If the product is not faulty, (i.e. if you changed your mind or if you are unhappy with the product for some other reason), the cost of shipping will fall on you. And it is your responsibility that the package arrives safely to us so we recommend that you use a courier service where it is possible to track theshipment.
LIMITED WARRANTY
If the product is faulty when you receive it, please contact us and we will
help
you out. We reserve the right to give a partial refund in cases when the
product(s) is not in an unused condition, is damaged or has missing parts, not
due to our error.
HOW RETURNS WORK
To request a return, please fill out the contact form on our website and
attach a copy of your invoice as proof of purchase and the reason for your
return in the message.
Then we will provide the return address for the product as soon as possible.
Once the returned product has been received by us and inspections have been
completed, a specific disposition will be provided to you.
In addition, if the return is approved, the refund amount will be
automatically credited to your original payment method.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>