AMERICAN PRODUCTS AM-202822-9RU Miniport Enclosure Owner’s Manual
- June 13, 2024
- AMERICAN PRODUCTS
Table of Contents
- Contacting Us
- Safety First
- Important Labeling Information
- Product Overview
- Product Specifications
- Options
- Installation
- Mounting Provisions
- Clearance Requirements
- Grounding Information
- FAN VENTILATION SYSTEM (OPTIONAL)
- 100 CFM Fan Wiring Diagram
- Appendix A
- CUSTOMER SUPPORT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AMERICAN PRODUCTS AM-202822-9RU Miniport Enclosure Owner’s
Contacting Us
American Products can be contacted for any issues that arise with the supplied product.
Technical assistance is available 9am to 4pm central standard time.
- Toll Free: 855-736-2135
- Phone: 417-736-2135
- Fax: 417-736-9535
- Email: Sales@amprod.us
- Web: www.amprod.us
When calling, please have available, or if faxing or emailing, be sure to provide:
- Part Number
- Serial Number
- Date of Purchase
- Date of Installation
Safety First
This publication provides a description of the American Products AP MINIFORT® enclosure. The mechanical descriptions, typical applications, installation instructions, safety guidelines, grounding and bonding are included.
Four types of messages may appear throughout this manual, identified by the following icons and signal words:
Read equipment manufacturer’s manual and this material before using this product. Failure to do so can result in serious injury or death.
DANGER
Indicates a hazardous situation that, if not avoided, will result in death or
serious injury. This signal word is to be limited to the most extreme
situations.
WARNING Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
NOTICE:
Indicates information considered important, but not hazards related (e.g.
messages relating to property damage). The safety alert symbol shall not be
used with this signal word. When a signal word is used for messages relating
to property damage, NOTICE is the choice of signal word.
Important Labeling Information
AP MINIFORT® Enclosure for Type 3R
Tested to Standards:
UL 50, UL 50E, CSA C22.2 No. 94.1, C22.2 No.94.2
Certification Testing performed at Intertek,plano TX
Product Overview
- The cabinet is constructed of Aluminum\Galvanized or Stainless Steel with optional powder coat painted finish for reduced weight and superior corrosion resistance. The front door is equipped with two quarter-turn latches.
- The equipment-mounting bay has a 9RU to 24RU of vertical 19”or 23” rack space in the front of the equipment bay. The 19” or 23” rack is also adjustable from front to rear. Two door options are also available for equipment accessibility.
- The cabinet utilizes stainless steel hardware, UL recognized EPDM edge gasketing (temp range of -40F to +212 F.
- When installing cabling or equipment that enters the cabinet, Type 3R entrances, fittings or equipment is to be used to maintain the integrity of the enclosure.
- No live equipment or components are to be installed below the lowest RU rack mounting provision or on the floor of the enclosure.
- The Cabinet is designed to allow various accessories to be mounted on the enclosure to meet customer requirements. For part number structure for Parent enclosure and accessories see diagram below:
Product Specifications
Options
Installation
The AP MINIFORT® cabinet should be mounted on a concrete pad. See the figure below for pad mounting hole patterns.
WARNING
During cabinet mounting, fixture the cabinet securely to avoid personal injury or cabinet damage.
CABINET MOUNTING LAYOUT
MOUNTING PLINTH LAYOUT
BATTERY/STORAGE BOX LAYOUT
Mounting Provisions
Clearance Requirements
When selecting a location to mount the cabinet, ensure that proper clearance is available to allow the cabinet door to open fully.
Grounding Information
Bonding and grounding should be done in accordance with industry standard procedures and comply with local electrical codes. The main cabinet ground bar is located in the rear of the cabinet as shown below.
FAN VENTILATION SYSTEM (OPTIONAL)
The AP MINIFORT® can be equipped with a fan ventilation system and thermostat
control.
The cabinet has two filters. The inlet filters are on the inside of the
cabinet. To replace the filter remove the four nuts that secure the filter
frame, remove old filter media and replace with new media and reinstall the
filter frame. The outlet filter, which primarily protects the cabinet from
dust and debris flowing to the cabinet when the fan is not active, is located
between the fan panel and the exterior louvers on the cabinet.
The fan forces air out of the top exterior louvers. This action draws outside
air into the cabinet through the bottom set of filtered louvers on the
exterior of the cabinet.
100 CFM Fan Wiring Diagram
Appendix A
Technical Support
American Products can be contacted for any issues that arise with the supplied
product.
Technical assistance is available 9am to 4pm central standard time.
- Toll Free: 855-736-2135
- Phone: 417-736-2135
- Fax: 417-736-9535
- Email: Sales@amprod.us
- Web: www.amprod.us
When calling, please have available, or if faxing or emailing, be sure to provide:
- Part Number
- Serial Number
- Date of Purchase
- Date of Installation
Warranty Policy
Enclosures designed and manufactured by American Products shall be warranted
to be free of defects in material or workmanship for a period of 5 years (U.S.
& Canada) and 3 years for International deployments from the date of
shipment. Should the product be proven to be defective, American Products will
have the option to repair or replace the product. Items included with the
enclosures, not manufactured by American Products, will carry the original
manufacturer’s warranty.
It is the responsibility of the buyer to communicate any special environmental
concerns in which the enclosures will be utilized. Special materials may be
required to allow for proper corrosion resistance for harsh environments. The
warranty does not cover enclosures used in applications and environments for
which they were not designed. Warranty does not cover abuse, modifications by
others or reimbursement for unauthorized rework. At no time will American
Products reimburse purchaser for unauthorized rework on any product.
Under no circumstances is American Products liable for any consequential
damages, liquidated damages, loss in profits or revenues, costs of capital,
downtime costs or damages related to our product performance.
Warranty Claims
Enclosures found to be defective will be repaired or replaced with the same or
comparable product.
All warranty claims must be communicated to our customer service
855-736-2135 department to obtain an
RMA number. For warranty claims in the USA and Canada, freight will be managed
and paid by American Products. For warranty claims outside of the USA and
Canada, the customer will be responsible for managing the freight and freight
expenses. Products being returned from other than US or Canada are to be
returned to the factory in Strafford, MO to receive warranty resolution, once
approved with an RMA.
Except for the express warranty stated above, American Products makes no other
warranties with respect to the product, expressed or implied, including but
not limited to merchantability or fitness for a particular purpose.
CUSTOMER SUPPORT
597 Evergreen Road Straff ord, Missouri 65757 Phone:
417-736-2135 Toll Free:
855-736-2135
www.amprod.us
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>