SimpliSafe VDP301 Video Doorbell Pro Installation Guide

SimpliSafe VDP301 Video Doorbell Pro

Installation Instructions

• Turn off the power to your doorbell at the circuit breaker

  • TIP: To locate the right switch, try turning each switch off, one at a time, and seeing if your doorbell rings

• Remove your existing doorbell
  Unscrew the doorbell, then unhook the wires from the back of the doorbell by loosening the screws that hold the wire ends. Make sure the wires don’t fall back into the wall.

  • TIP: Wrap the wires around a pencil and use tape to prevent them from falling back into the wall

• Thread the doorbell wires through the center of the mounting bracket

• • To correct the angle of your doorbell with the included angled base, go to Optional Install B
    • To install on a stone, brick, or stucco surface, go to Optional Install C

• Screw the mounting bracket to the wall

  • Use the 2 included 1* screws to install the mounting bracket.

• Connect the wires to the mounting bracket

  • a. Laosen terminal screws
  • b. Slide exposed wire behind the square washers and around each screw Iwires can connect to either screwl.
  • c. Tighten screws to secure wires

TIP: Place wire ends to the left of each screw

• Slide your doorbell into place

  • Push the doorbell onto the mounting bracket and slide down until it clicks
  • Turn on the power to your doorbell at the circuit breaker

• Press the doorbell to test the chime connection

  • Did your doorbell chime? If yes, it’s working! it not, check that wires are secure.

Note: The camera battery may need a few minutes to charge before the camera can be connected to WiFi. LED ring will blink white after the button is pressed when the camera is ready for setup.

• Now it’s time to set your wifi

  • Open the SimpliSafe app on your mobile device and navigate to “Set up my SimpliCam” to finish installing.

• Scan this QR code to download the Simal Safe app

OPTIONAL INSTALL A

Secure doorbell

Use the mini screwdriver to insert the mini lock screw at the bottom of the doorbell.

OPTIONAL INSTALL B

Installing with the angled base

• The included angled base straightens a doorbell placed on a slanted surface such as siding or shingles, or may be used to adjust the angle of the camera up or down
• First, screw the Angied Base to the wall
• Place the angled base with the smooth side to the wall. Thread doorbell wires through the center opening, then screw the bracket to the wall using the 1ª screws.

Bracket on top

• Screw mounting bracket onto angle bracket using the two small angle-bracket
• Return to Step 5 to continue the install

OPTIONAL INSTALL C

Installing on stone, brick, or stucco surfaces

• First. mark the whole location
• Mark the wall first with a pencil, using the mounting bracket holes as a template.
• Then, drill holes and insert wall anchors
• Drill a hole at each pencil mark with a 3/16 (4.75mm) masonry bit Insert wall anchors into the holes by gently tapping with a hammer or mallet.

Return to Step 4 to continue the install

Frequently Asked Questions

How do I turn off the power to my SimpliSafe VDP301 Video Doorbell Pro at the circuit breaker?

Locate the circuit breaker panel in your home. Identify the circuit breaker that controls the power to your doorbell. Switch the corresponding circuit breaker to the off position to cut off power to the doorbell.

What should I do if my SimpliSafe VDP301 Video Doorbell Pro doesn't chime after installation?

Check that the wires are securely connected to the mounting bracket. Ensure that the power is turned on at the circuit breaker. Press the doorbell button to test the chime connection. If the issue persists, review the installation steps to ensure everything is correctly set up.

How long does it take for the battery of my SimpliSafe VDP301 Video Doorbell Pro to charge before connecting to WiFi?

The camera battery may need a few minutes to charge before it can be connected to WiFi. The LED ring will blink white after the button presses when the camera is ready for setup.

How do I set up WiFi for my SimpliSafe VDP301 Video Doorbell Pro?

Open the SimpliSafe app on your mobile device. Navigate to Set up my SimpliCam to finish installing. Follow the on-screen instructions in the app to connect your Video Doorbell Pro to your WiFi network.

What is the purpose of the optional installations A, B, and C for my SimpliSafe VDP301 Video Doorbell Pro?

Optional Install A: Securing the doorbell with a mini lock screw for added security. Optional Install B: Using the angled base to adjust the angle of the doorbell, is especially useful for slanted surfaces. Optional Install C: Installing the doorbell on stone, brick, or stucco surfaces using wall anchors for stability and durability.

What is the warranty coverage for the SimpliSafe VDP301 Video Doorbell Pro?

The warranty coverage typically includes defects in materials and workmanship for a specific period, usually one year from the date of purchase. Contact SimpliSafe customer support for detailed warranty information.

Can I install the SimpliSafe VDP301 Video Doorbell Pro myself, or do I need professional installation?

The SimpliSafe VDP301 Video Doorbell Pro is designed for DIY installation. However, if you're unsure or uncomfortable with the installation process, you can opt for professional installation services offered by SimpliSafe.

Is the SimpliSafe VDP301 Video Doorbell Pro compatible with smart home platforms like Amazon Alexa or Google Assistant?

SimpliSafe VDP301 Video Doorbell Pro is typically compatible with popular smart home platforms like Amazon Alexa and Google Assistant. You can check the official SimpliSafe website or product documentation for the latest compatibility information and setup instructions.

What should I do if I need technical support or assistance with my SimpliSafe VDP301 Video Doorbell Pro?

If you need technical support or assistance, you can contact SimpliSafe customer support through various channels, including phone, email, or live chat. Check the SimpliSafe website for the most up-to-date contact information and support options.

How do I adjust the motion detection settings on the SimpliSafe VDP301 Video Doorbell Pro?

You can adjust the motion detection settings using the SimpliSafe mobile app. Navigate to the settings menu for your video doorbell within the app, and you should find options to customize motion sensitivity, detection zones, and notification preferences.

Can I view live footage from the SimpliSafe VDP301 Video Doorbell Pro remotely?

Yes, you can view live footage from the SimpliSafe VDP301 Video Doorbell Pro remotely using the SimpliSafe mobile app. Simply open the app and access the live feed from your doorbell camera to see real-time activity at your door.

What type of internet connection is required for the SimpliSafe VDP301 Video Doorbell Pro to function properly?

The SimpliSafe VDP301 Video Doorbell Pro requires a stable WiFi connection to function properly. Ensure that you have a reliable internet connection with sufficient bandwidth to support video streaming from the doorbell camera.

Is there a subscription fee required to use all features of the SimpliSafe VDP301 Video Doorbell Pro?

While some basic features of the SimpliSafe VDP301 Video Doorbell Pro may be available without a subscription, certain advanced features, such as cloud storage for video recordings and access to extended features in the mobile app, may require a subscription plan. Check SimpliSafe's subscription options for more details.

Can I use the SimpliSafe VDP301 Video Doorbell Pro without an existing doorbell wiring setup?

Yes, the SimpliSafe VDP301 Video Doorbell Pro can be used without an existing doorbell wiring setup by utilizing the battery power option. However, keep in mind that you may need to recharge or replace the battery periodically, depending on usage.

Video- Product Overview

Download The PDF link:SimpliSafe VDP301 Video Doorbell Pro Installation Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>