VEVOR ATSA1420 Vehicle Awning User Manual

VEVOR ATSA1420 Vehicle Awning

SPECIFICATIONS

COMPONENTS

• Manual x1
• Stainless Steel Ground Peg x4
• Black Powdercoated Steel Bracket x2
• Black Powdercoated Steel Backing Plate x2
• 2.7m Rope with Plastic Fixed unit x2
• SS304 M8X20mm bolt x4
• SS304 M8X55mm bolt x4
• SS304 M8 Nylock nut X8
• WRENCH x2
• Carry Bag x1

FITTING GUIDE

INSTALLATION FOR ROOFTOP RACK

Options for mounting your awning are outlined below. It is important when mounting the awning to ensure it is positioned to allow sufficient clearance for the vehicle doors to open.

FOR CROSS BAR (DRILLING MIGHT BE NEEDED)

If there are no holes in the cross bar, it is necessary to drill the holes before installing the bracket.

STEP 1 Cross bar drilling

STEP 2 Bracket installing

Note: Partial DIY might be needed due to different fittings of rooftop rack models. Not all provided parts are necessary for installation, some are backups for different models.

SETUP

1. STEP 1: Unzip the PVC Protective Bag
2. STEP 2: Unhook the straps
3. STEP 3: Open the lateral support poles
4. STEP 4: Rotate the lower part of the poles to adjust the length of the pole
5. STEP 5: Unfold the awning
6. STEP 6: Open the vertical support poles
7. STEP 7: Rotate the lower part of the poles to adjust standing height
8. STEP 8: Tie camping ropes through joint holes, set ground pegs, and tension all ropes

SETUP PROCEDURE:

1. Clean only with cold water and a soft brush-do not use soap or detergent.
2. Do not expose to petrol, oil, or solvents.
3. Avoid creases and seams when rolling up the awning.

IMPORTANT SAFETY WARNING

FAQs

• Q: How do I clean the awning?
  • A: Clean only with cold water and a soft brush-do not use soap or detergent.
• Q: What should I avoid when using the awning?
  • A: Do not expose it to petrol, oil, or solvents. Avoid creases and seams when rolling up the awning.
• Q: Can I use the provided parts for any model?
  • A: Not all provided parts are necessary for installation; some are backups for different models.
• Q: Do I need to drill holes for installation on a crossbar?
• A: If there are no holes in the crossbar, it is necessary to drill them before installing the bracket.
  • We continue to be committed to provide you tools with at competitive price. “Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us: Technical Support and E-Warranty Certificate

• www.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

SPECIFICATIONS

COMPONENTS

SN

| FITTING

LIST-SPECIFICATIONS

| ****

PICTURE

---|---|---
1| Manual x1| ****
2| Stainless Steel Ground Peg x4

3

| Black Powdercoated Steel L –

Bracket x2

4

| lack Powdercoated Steel

Backing Plate x2

5

| 2.7m Rope with Plastic Fixed

unit x2

6| SS304 M8X20mm bolt x4
7| SS304 M8X55mm bolt x4
8| SS304 M8 Nylock nut X8
9| WRENCH x2
10| Carry Bag x1

Simply follow the easy assembly instructions in this manual, and follow the setup and safety guidelines closely.

Inspections: during trips regularly check that all nuts and bolts attaching your awning to your vehicle are tight and in good repair.

IMPORTANT SAFETY WARNING

• Do not attempt to set up the awning in windy conditions.
• All guy ropes must be properly attached to the awning and pegged to the ground at all times.
• Guy ropes are trip hazards in the day and night.
• Keep all flame and heat sources away from the awning materials. Under no circumstance should any naked flame sources, fuel burning devices or heating devices be used under or near the awning.
• Keep campfires well away from awning.
• Keep a look out for any airborne burning embers that may come into contact with the awning.
• Keep a fire extinguisher or water bucket nearby.
• Do not smoke within the awning. Keep exit clear.

FITTING GUIDE

Options for mounting your awning are outlined below.  It is important when mounting the awning to ensure it is positioned to allow sufficient clearance for the vehicle doors to open.

INSTALLATION

FOR ROOFTOP RACK

NOTE: You can choose option A or option B to install according to your requirements.

FOR ROOFTOP BASKET

NOTE: You can choose option A or option B to install according to your requirements.

FOR CROSS BAR (DRILLING MIGHT BE NEEDED)

NOTE: If there are no holes in the crossbar, it is necessary to drill the holes before installing the bracket.

• STEP 1：Cross bar drilling
• STEP 2：Bracket installing

Note: Partial DIY might needed due to different fittings of rooftop rack models. Not all provided parts are necessary to be used for installation, some of them are backups for different models.

SETUP

STEP1

• Unzip the PVC Protective Bag

STEP2

• Unhook the straps

STEP3

• Open the lateral support poles.

STEP4

• Rotate the lower part of the poles to adjust the length of the pole.

STEP5

• Unfold the awning.

STEP6

• Open the vertical support poles.

STEP7

Rotate the lower part of the poles to adjust standing height.

STEP8

Tie camping ropes through joint holes, set ground pegs and tension all ropes.

SETUP PROCEDURE

1. Clean only with cold water and a soft brush-do not use soap or detergent.
2. Do not expose to petrol, oil or solvents
3. Avoid creases and seams when rolling up the awning.

• Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
• Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
• Imported to the USA: Sanven Technology Ltd.Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

SHUNSHUN GmbH Römeräcker 9 Z2021,76351 Linkenheim-Hochstetten,Germany

Pooledas Group Ltd Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom

Technical Support and E-Warranty Certificate

• www.vevor.com/support

References

• Contact Us – Official VEVOR Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>