DV8 OFFROAD INFEND-05RB Rear Inner Fenders

Product Information

Specifications:

• Product Name: Rear Inner Fenders
• Compatibility: 2021+ Ford Bronco
• Model Number: INFEND-05RB
• Manufacturer: DV8 Offroad

Tools Required:

• Ratchet

• 4 Allen Head

• Drill
• 11/32 Drill Bit
• Nutsert Tool (M6)
• Philips Head Screwdriver

Warnings/Cautions Before Starting Installation:

• Read and understand all instructions, warnings, cautions, and notes contained in this installation instruction guide.
• Consult your vehicle owner’s manual for proper disconnection of electrical and lifting of vehicle if required for installation of this product.
• This installation may require some technical skills and knowledge of basic mechanical work. If you do not feel that you are capable of performing this install please take this product to a trained professional.
• After reading this guide please contact us with any questions or concerns before installing product. Customer Service: 855-680-9595
• DV8 Offroad is not responsible for any bodily injury or harm to you or your vehicle as a result of an improper install.
• Proper installation of this kit required knowledge of the factory-recommended procedures for removal and installation of original equipment components.
• We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation.
• Installation of this kit without proper knowledge of the factory-recommended procedures may affect the performance of these components and the safety of the vehicle.
• Inspect all contents of this package to make sure the product is not damaged and all installation hardware has been included.
• If parts are missing from kit, please be prepared to provide the following information:
  1. Name of purchase location
  2. Bar Code on side of box
  3. Date above bar code
  4. Date inside box cover

Product Usage Instructions

Uninstall Manual – Step 1
You will need to fully remove the front fenders by turning the clips on the underside of the fender down until they feel loose. Once loose, pull the fender away from the Bronco directly towards you, releasing the clips.
Note: Both front and rear fenders are mounted in this manner.

Tools Required:

• Ratchet
• 7mm Deep Socket
• Panel Clip Removal Tool
• Philips Head Screwdriver

Uninstall Manual – Step 2
Use a philips head screw driver and panel clip removal tool to remove the various clips securing inner fender to the vehicle.

Uninstall Manual – Step 3
Use a 7mm deep socket to remove the nuts securing the inner fender, located at the top of the inner fender and lower front section of the inner fender.
Note: Passenger side will have two nuts securing it in the top section.

Uninstall Manual – Step 4
Remove inner fender by pulling down by the lip of the fender and out.

Installation Manual – Step 1
Begin by unpacking all items and inspecting for missing pieces or damage. If you have any concerns, please contact the company the product was purchased from.

FAQ

• Q: What tools are required for installation?
  A: The tools required for installation are a ratchet, #4 Allen Head, drill, 11/32 drill bit, nutsert tool (M6), and Philips head screwdriver.

• Q: How long does it take to install this product?
  A: It should take about 3 hours to install this product.

• Q: Can I install this product by myself?
  A: Yes, little skill level is required, and you can easily install it by yourself. However, additional help will be useful.

TOOLS REQUIRED

• Ratchet

• 4 Allen Head

• Drill
• 11/32” Drill Bit
• Nutsert Tool (M6)
• Philips Head Screwdriver

SKILL LEVEL

• Novice/Intermediate
• 1 (you) to 2 persons

Little skill level required, you can easily install it by yourself however, additional help will be useful.

TIME REQUIRED

• 3 Hour

Time to install this should only take about 3 hours.

WARNINGS

WARNINGS/CAUTIONS BEFORE STARTING INSTALLATION

• Before you install this kit — Read and understand all instructions, warnings, cautions, and notes contained in this installation instruction guide. Consult your vehicle owner’s manual for proper disconnection of electrical and lifting of vehicle if required for installation of this product.

• This install may require some technical skills and knowledge of basic mechanical work. If you do not feel that you are capable of performing this install please take this product to a trained professional.

• After reading this guide please contact us with any questions or concerns before installing product.
  Customer Service: 855-680-9595

• DV8 Offroad is not responsible for any bodily injury or harm to you or your vehicle as a result of an improper install.

• Proper installation of this kit required knowledge of the factory recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle

• Always wear eye protection when operating power tools

• Inspect all contents of this package to make sure product is not damaged and all installation hardware has been included. If parts are missing from kit, please be prepared to provide the following information

  1. Name of purchase location
  2. Bar Code on side of box
  3. Date above bar code
  4. Date inside box cover

INSTALLATION INSTRUCTION

1. STEP 1 You will need to fully remove the front fenders by turning the clips on the underside of the fender down until they feel loose. Once loose, pull the fender away from the Bronco directly towards you, releasing the clips.
   Note: Both front and rear fenders are mounted in this manner.
   Tools Required:

2. Ratchet

3. 7mm Deep Socket

4. Panel Clip Removal Tool

5. Philips Head Screwdriver

6. STEP 2 Use a philips head screw driver and panel clip removal tool to remove the various clips securing inner fender to the vehicle.
   UNINSTALL MANUAL

7. STEP 3 Use a 7mm deep socket to remove the nuts securing the inner fender, located at the top of the inner fender and lower front section of the inner fender.
   NOTE: Passenger side will have two nuts securing it in the top section.

8. STEP 4 Remove inner fender by pulling down by the lip of the fender and out.

INSTALLATION MANUAL

• STEP 1 Begin by unpacking all items and inspecting for missing pieces or damage. If you have any concerns, please contact the company the product was purchased from.
  Hardware Included:

  • (16) M6x20
  • (19) M6x14
  • (16) M6 Serrated Nuts
  • (19) M6 Nutserts

• STEP 2 Assemble the DV8 inner fender using a #4 allen head and provided M6x20 hardware. The upper piece will sit on top of the lower piece.
  NOTE: Ensure mesh hardware issecure before installation. Drivers side is pictured.

• STEP 3 Bend back the tabs that will not be used during installation. (From the front you will bend the 1st, 3rd, 4th, 6th, and 7th tabs). The remaining tabs that will be used for installation can be adjusted by hand to better line up with the inner fender during installation. If you are unsure of which tabs to bend, you can maneuver the inner fender into the wheel well and reference the mounting holes on the inner fender to find the mounting tabs.

• STEP 4 Use 11/32” inch drill bit to drill out the holes on the remaining tabs.

• STEP 5 Install provided nutserts into the remaining tabs using a nutsert tool.

• STEP 6 Manuever the inner fender into the wheel well carefully as not to damage the inner fender. It may take a few attempts to get it correct. Install the DV8 inner fenders using a#4 allen head and provided M6x14 hardware.

• STEP 7 Reinstall factory screw with philips head screwdriver. Located towards the lower front section of the inner fender.

• STEP 8 OPTIONAL: You may choose to remove the clip for the wiring harness and push it back for a cleaner look.

• STEP 9 Double check fitment and all hardware is secure. Repeat steps for other side.

NEED HELP? 855-680-9595
6400 SYCAMORE CANYON BLVD.
RIVERSIDE, CALIFORNIA 92507
855-680-9595
WWW.DV8OFFROAD.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>