DRYEASY Bedwetting Alarm with Volume Control Instruction Manual

Table of Contents

DRYEASY-Bedwetting-Alarm-with-Volume-Control-PROCUT

Safety Precautions

This product is not suitable for children under 5 years of age. Always use it under adult supervision.
Make sure the cord is not tangled around the user to prevent accidents.
Read the enclosed manual thoroughly before using the product.
If you have any doubts about using the product, consult your doctor.

Unpack the product and read the manual carefully.
Ensure the cord is untangled and in good condition.
Follow the instructions provided in the manual for operating the product.
If you experience any discomfort or unusual symptoms, stop using the product immediately and seek medical advice.

DRYEASY-Bedwetting-Alarm-with-Volume-Control-FIG-1

A. To set up the alarm:

Remove the insulation tag from the battery compartment (for first-time use only).
Insert the plug of the cord into the alarm socket.
Test the alarm by touching the sensor tip (metal prong) with a wet finger. Press the “Reset” button to stop the alarm from sounding.

B. To adjust the volume level, select operation mode and sound:

Open the battery compartment door and press the “+” or “-” key for volume adjustment.
Slide the switch inside the battery compartment for a change of operation mode from “vibration only” to “vibration and sound” and “sound only”
To select a desired sound, choose a sound group (A or B) by sliding the sound group selection switch and then choose a sound (1, 2 or 3) from the sound selection switch (6 sounds available for selection. Al, A2, A3, B1, B2 & B3).
To play the sounds at random, slide the sound group selection switch to R.

C. To attach the alarm and the sensor:

Attach the alarm to the pyjamas by following the steps set out below (see Figure A):
Lift up the lever
Place the pyjamas into the mouth of the alarm clip
Lock the alarm clip by pressing down the alarm lever
(Note : For best results, fix the alarm close to the collar bone)
Run the cord under the pyjamas as it can prevent the sensor from being dislodged (see Figure B).
Attach the sensor to the outside of close-fitting underpants in the following manner:

(Tip: P ull down the underpants slightly for easy fixing of sensor )

DRYEASY-Bedwetting-Alarm-with-Volume-Control-FIG-3

Important : The sensor should be attached with the cover facing up (as shown below)

DRYEASY-Bedwetting-Alarm-with-Volume-Control-FIG-4

(Note: To detach the sensor from the underpants, simply lift up the tail of the cover)

D. To stop the alarm from sounding when bedwetting occurs:

DRYEASY-Bedwetting-Alarm-with-Volume-Control-FIG-5

Useful tips

Parents are recommended to have a trial run of all steps for the use of the alarm during the time with the child before the first time use.
The child must wear a pair of close-fitting underwear as the urine can be detected faster. DO NOT wear loose underwear or boxer shorts.
Rapid response to the alarm alert can enhance the success rate in overcoming bedwetting. Parents play an important role, in particular at the initial stage, in awakening the child as soon as the alarm goes off and are therefore recommended to sleep in the same room with the child for the first 2 weeks of using the alarm.
Use the stickers and progress chart to track the progress.
Typical treatment takes 6-12 weeks but it varies from person to person. Motivation and persistence are very important for success.
Keep using the alarm for 2 more weeks after dryness to lower the chance of relapse.

We offer you a one-year warranty for manufacturer’s defects. For details, please visit our website or contact us by email.

For small to medium arm size (from 15 cm to 27 cm)

Clip the alarm near the buckle
Thread the strap through the buckle to form a loop
Slip onto the arm and tighten the strap until it is comfortable (it should be snug enough to keep the alarm in place, but not so tight that it restricts arm circulation).

For instructions in other languages, please visit the link below or scan the QR code as shown:

If you have any questions about our products or warranty, please email to: info@bedwettingsolving.com
We will give you a reply within 24 hours.

Satisfied with our product?
Please take a couple of minutes to give us a product review on Amazon.

To submit a review, please follow the steps below:

Thank you for your support!

Attention

The alarm can be attached to the pyjama top or to the arm with the use of an armband. DO NOT attach the alarm to the underwear
The proper way to stop the alarm from going off:
- Remove the sensor from the wet underwear
- Press the “Reset” button on the alarm
  To watch the video, visit the link below or scan the QR code as shown www.bedwettingsolving.com/en/video2.mp4
Do not unplug the cord from the alarm except for sensor- cleaning. To unplug the cord, press the tab and pull it out. Never pull the cord out by force as it may get damaged.
Do not wet the plug when cleaning the sensor. If it gets wet, dry it before use.
The alarm is NOT waterproof! Never immerse it in water or urine.