TYGER TG-LX3F82448 LanderX Running Board Instruction Manual
- June 1, 2024
- TYGER
Table of Contents
TYGER TG-LX3F82448 LanderX Running Board Instruction Manual
BEFORE INSTALLATION
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT.
TORQUE VALUES
Fastener Size| Class 8.8 Torque (ft-lbs)| Class 10.9 Torque (ft-
lbs)
---|---|---
6mm| 6-7| 6-7
8mm| 15-16| 22-23
10mm| 31-32| 44-45
12mm| 54-55| 78-79
14mm| 87-88| 125-126
- x1 Driver/Left TYGER LanderX
- X1 Passenger/Right TYGER LanderX
- x1 Driver/Left Front Mounting Bracket (A)
- x2 Driver/Left Center/Rear Mounting Brackets (B)
- x1 Passenger/Right Front Mounting Bracket C
- X2 Passenger/Right Center/Rear Mounting Brackets D
- x12 10-1.5mm x 25mm Hex Bolts
- x12 10mm Lock Washers
- x12 10mm x 27mm OD x 3mm Flat Washers
- x12 8mm x 25mm Combo Bolts
Reference the letters printed on the brackets to determine mounting
locations
Driver/Left TYGER LanderX
Passenger/Right TYGER LanderX
Bottom View
ATTENTION : Refer to the D or P labelling on the tubes to determine the
Driver or Passenger side steps.
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION
STEP 1
Starting installation under the driver/left side inner rocker panel.
Locate the threaded mounting holes in the rocker panel toward the front wheel
opening ( Fig 1). Remove the plastic plugs covering the mounting holes.
Select the Driver/Left Front Mounting Bracket (Fig 2). Attach Bracket to
driver/left front location with (2) 10mm x 30mm Hex Bolts, (2) 10mm Lock
Washers and (2) 10mm Flat Washers ( Figs 2 & 3). DO NOT fully tighten
hardware.
Driver/left side Installation Pictured
(Fig 1) Driver/left front mounting location
(Fig 2) Driver/Left Front Mounting Bracket installation
(Fig 3) Driver/Left Front Mounting Bracket attached
STEP 2
Move to the center of the vehicle and locate the threaded mounting holes (Fig
4). Select (1) Driver/Left Center/Rear Mounting Bracket (Fig 5). Attach the
Bracket to the threaded holes with the included (2) 10mm x 25mm Hex Bolts, (2)
10mmLock Washers and (2) 10mm Flat Washers (Figs 5 & 6). DO NOT fully tighten
hardware.
Driver/left side Installation Pictured
(Fig 4) Driver/left Center mounting location
(Fig 5) Driver/Left Center and Rear Mounting Bracket installation
(Fig 6) Driver/Left Center Mounting Bracket installed
STEP 3
Move to the last threaded holes closest to the rear wheel opening (Fig7).
Select the remaining Driver/Left Center/Rear Mounting Bracket (Fig 5). Repeat
STEP 2 to attach the Rear Mounting Bracket (Figs 5 & 8). DO NOT fully tighten
hardware.
Driver/left side Installation Pictured
(Fig 7) Driver/left Rear mounting location
(Fig 8) Driver/left Rear Mounting Bracket installed
STEP 4
Carefully unwrap the TYGER Lander X. Select the Driver/Left TYGER Lander X.
Line up the TYGER Lander X with the (3) Mounting Brackets. Attach the TYGER
Lander X to the Brackets with the included (6) 8mm x 25mm Combo Hex Bolts
(Figs 9-13).
Driver/left side Installation Pictured
(Fig 9) Attach Driver/Left TYGER LanderX to Front Bracket
(Fig 10) Driver/Left LanderX attached to Front Bracket
(Fig 11) Attach Driver/Left TYGER LanderX to Center and Rear Brackets
(Fig 12) Driver/Left TYGER LanderX attached to Center Bracket
(Fig 13) Driver/Left TYGER LanderX attached to Rear Bracket
STEP 5
Level and adjust the TYGER LanderX and tighten all hardware.
STEP 6
Repeat STEPS 1-5 to install the Passenger/Right TYGER LanderX “P”.
STEP 7
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>