TYGER TG-LD2J62398 Lander Running Board Instruction Manual

TYGER TG-LD2J62398 Lander Running Board

Specifications

• Product Name: TYGER LANDERTM TG-LD2J62398

Fastener Torque Values:

Product Usage Instructions

1. Step 1: Remove Contents and Preparation

2. Remove all parts from the box and ensure everything is present.Review the instructions carefully. Remove any factory-installed or aftermarket products before installation.

3. Step 2: Front Installation

4. Start the installation on the passenger/right side of the vehicle towards the front. Attach the front mounting bracket using the provided hardware but do not tighten yet.

5. Step 3: Mounting Brackets
   Determine if your vehicle has threaded mounting inserts. Follow the instructions accordingly for vehicles with or without threaded inserts.

6. Step 4: Center and Rear Installation
   Repeat the bracket attachment process for the center and rear locations, ensuring not to tighten the hardware just yet.

7. Step 5: Attaching Tyger Lander
   Attach the Tyger Lander to the rear faces of the Center and Rear Mounting Brackets using the provided hardware. Be careful not to slide or rotate the Sidebar on the Front Mounting Bracket cradle to avoid damaging the finish.

FAQ:
Q: What should I do if I find missing parts or damage before installation?
A: If you find missing parts or damage, take a picture for claim purposes and visit www.TygerAuto.com/contact to file your claim.

BEFORE INSTALLATION

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT

TORQUE VALUES

Parts List

• Driver/Left Tyger Lander
• Passenger/Right Tyger Lander
• Driver/Left Front Mounting Bracket
• Passenger/Right Front Mounting Bracket
• Driver/Left Center Mounting Bracket
• Passenger/Right Center Mounting Bracket
• Driver/Left Rear Mounting Bracket
• Passenger/Right Rear Mounting Bracket
• 10-1.5mm x 35mm Hex Bolts
• 10mm x 27mm OD x 3mm Flat Washers
• 10mm Nylon Lock Nuts
• 8mm Nut Plates
• 8-1.25mm x 35mm Hex Bolts
• 8-1.25mm x 25mm Combo Bolts
• 8mm Lock Washers
• 8mm x 28mm OD x 3mm Flat Washers
• 6-1.0mm x 25mm Hex Bolts
• 6mm x 22mm OD x 2mm Flat Washers
• 6mm Nylon Lock Nuts

1. STEP 1
   REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. FACTORY INSTALLED OR AFTERMARKET PRODUCT MUST BE REMOVED.
   

2. STEP 2
   Start installation toward the front of the Passenger/Right side of the vehicle (Fig 1).

3. STEP 3
   Determine if vehicle is equipped with threaded mounting inserts
   Vehicles without threaded inserts:
   a. Insert (1) 10mm Nut Plate into the large square opening in the floor panel. Line up the threaded nut with the hole in between the pair of holes on the pinch weld (Figs 2A & 2B).

   • Select the Passenger/Right Front Mounting Bracket.

   • Attach the Bracket to the Nut Plate with (1) 8mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer (Fig 3). DO NOT tighten hardware.

   •  Attach the Mounting Bracket to the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts (Fig 3). DO NOT tighten hardware.
     Vehicles with factory threaded hole in floor panel:

   • Locate the front, center and rear mounting locations (Fig 1).

   • Select the Passenger/Right Front Mounting Bracket.

   • Attach the Bracket to the front mounting location with (1) 8mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer (Fig 3). DO NOT tighten hardware.

   • Attach the Mounting Bracket to the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts,(Fig 3). DO NOT tighten hardware.

4. STEP 4
   Repeat STEP 3 to attach the Brackets to the center and rear locations (Figs 4A, 4B & 5). DO NOT tighten hardware.

5. STEP 5
   Select the Passenger/Right Tyger Lander. Attach the Tyger Lander to the rear faces of the Center and Rear Mounting Brackets with (4) 10mm Hex Bolts, (8) 10mm Flat Washers and (4) 10mm Nylon Lock Nuts (Fig 6).
   IMPORTANT: DO NOT slide or rotate Sidebar on the Front Mounting Bracket cradle, or damage to the finish may result.

6. STEP 6
   Attach the Tyger Lander to the Front Mounting bracket with (2) 8mm Combo Bolts (Fig 7). DO NOT tighten hardware.
   Passenger/Right Side Installation Pictured

7. STEP 7
   Level and adjust the Tyger Lander and tighten all hardware.

8. STEP 8
   Repeat STEPS 1-7 to attach the Driver/Left Tyger Lander.

9. STEP 9
   Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Customer Support: www.TygerAuto.com/Contact

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>