Good Earth UC1360-WHG-12LFW WIFI LED Bar for Under Cabinets Instruction Manual

Good Earth UC1360-WHG-12LFW WIFI LED Bar for Under Cabinets

Product Specifications

• Model #: UC1360-WHG-12LFW, UC1360-WHG-24LFW-G
• Includes: Screw Cover, Linking Cord, Diffuser, Hardware Kit
• Indoor Damp Location Use Only
• LEDs gradually emit less light over their lifetime
• Maximum additional fixtures: 20 for 12-inch bar, 10 for 24-inch bar

Product Usage Instructions:

Safety Information

• Use only insulated staples or plastic ties to secure cords.
• Route and secure cords to prevent pinching or damage.
• Do not look directly at exposed LEDs; turn off power before servicing.
• Avoid mounting over sinks, stoves, or inside enclosed cabinets.

Installation

1. Clean mounting surface with rubbing alcohol.
2. Apply adhesive strips on the back of the fixture and press firmly for 30 seconds.
3. Use included cord clips for cord management by following the provided instructions.

Removal

• Gently hold the light or clip in place with one hand.
• Slowly stretch each strip against the surface to release.

Screw Mount Installation

1. Remove screw covers on both ends and ensure proximity to an electrical outlet.
2. Drive pre-installed screws straight into the bottom surface of the cabinet.
3. Do not overtighten to prevent stripping the screw hole.

Optional: Installing Additional Lights
Once installation is complete, plug each additional fixture into the fixture ahead of it. For a 12-inch bar, you can add a total of 20 fixtures, and for a 24-inch bar, you can add up to 10 fixtures.

Frequently Asked Questions (FAQ)

• Q: Can this product be used outdoors?
  A: No, this product is suitable for indoor damp locations only.

• Q: How many additional fixtures can be added to each bar?
  A: You can add up to 20 fixtures to the 12-inch bar and 10 fixtures to the 24-inch bar.

SAVE AND ATTACH RECEIPT HERE

WIFI LED Undercabinet Bar

Model

Required

Hardware kit

• Actual hardware may differ from illustration./

READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!

SAFETY INFORMATION

ATTENTION

• Use only insulated staples or plastic ties to secure the cords.
• Route and secure the cords so that they will not be pinched or damaged.
• LEDs gradually emit less light over their lifetime.
• Only the bars (Model #UC1360-WHG-12LFW/UC1360-WHG-24LFW ) can be linked to undercabinet bara. 20 additional bars can be added to the 12 inch bar, and 10 to the 24 inch bar.
• Suitable for INDOOR damp locations ONLY.

WARNING

• LED light output is strong enough to injure human eyes. Do not look directly at exposed LEDs.
• Turn power off before servicing.
• Ensure cords are unplugged when securing or moving.

CAUTION

• DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT.
• Do NOT use with an extension cord, use ONLY with power strips that have integral overcurrent protection.
• Do NOT mount to surfaces less than ¼ in. thick.
  • A. For installation with Command® Strips by 3M: Do NOT mount over sinks, stoves, beds or inside of enclosed cabinets. Do NOT mount on wallpaper.
  • B. For installation using screws: Do NOT mount over sinks, stoves, or inside of enclosed cabinets.
• Not intended for recessed installation in ceiling or soffits.

EASY INSTALLATION COMMAND® STRIPS BY 3M

1. NOTE : Ensure mounting location is within 5ft. of an electrical outlet. Clean surface with rubbing alcohol. Remove red liners. Press two medium strips to the back of the 12in fixture, and three on the 24in. fixture. Remove black liners. Press the fixture to surface with tab towards you. Press firmly for 30 sec.
2. Use the 2 included clear cord clips for cord management. To apply, clean surface with rubbing alcohol. Use the 2 additional small strips for cord clips. Remove red liners. Press the strips to the back of the clip. Remove black liners. Press each clip firmly to the surface for 30 sec. Insert cords into cord clips and plug into outlet.

REMOVAL

Gently hold the light or clip in place with one hand. NEVER PULL THE STRIP AWAY FROM THE SURFACE! Always pull along the surface. Slowly stretch each strip slowly against the surface at least 12 inches to release.

SCREW MOUNT INSTALLATION

1. Remove screw covers on both ends. NOTE: Ensure mounting location is within 5ft. of an electrical outlet.
2. Hold the fixture and drive pre-installed screws until they contact the bottom surface of the cabinet. The wood screws must be driven in straight for the fixture to mount properly. DO NOT OVERTIGHTEN to prevent stripping the screw hole.
3. Replace screw covers on both ends. Use included cord clips for cord management. ( See step 2 on page 1.)

OPTIONAL: INSTALLING ADDITIONAL LIGHTS

DIMMING AND CCT

Tap button to turn on/off. Hold button down to dim the fixture. Manual Control: Short press
COLOR ADJUST button to select 3000K/4000K/5000K, Red, Green, Blue, Pink, Orange, Auto rotating colors.
WIFI Control: See APP instruction sheet for direction.

CARE AND MAINTENANCE:

Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner and soft cloth. When cleaning the fixture, make sure the power is turned off. Do not spray cleaner directly onto any part of the fixture or LEDs.

Good Earth Lighting® – 6 YEAR LIMITED WARRANTY:
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (6) years from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.

FCC STATEMENT:

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that of the receiver.
4. Consult the dealer or an experienced radio/TV technician for help.

FCC responsible party name : Good Earth Lighting, Inc. Address: 1400 E Business Center Drive, STE 108, Mount Prospect IL 60056, USA
Telephone number: 1-800-291-8838

TROUBLESHOOTING GUIDE

supply and light switch are on.
2. Bad switch.| 2. Test or replace switch.
2. Fuse blows or circuit breaker trips when light is turned on.| 1. Discontinue use.| 1. Call customer service (1-800-291-8838).

REPLACEMENT PARTS LIST
Hardware Kit: ZH-UC1360-F12, ZH-UC1360-F24

Need Help?
Please visit our website at: https://goodearthlighting.com/contact-us or call the Customer Care Center 1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.

Good Earth Lighting® 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056 Good Earth Lighting® is a registered trademark of Good Earth Lighting, Inc.
© 2023 Good Earth Lighting, Inc. REV01.23
Printed in Vietnam

References

• Contact Us | Good Earth Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>