Good Earth IN_AC1347-CCT-07LF0-G LED USB Tape Light User Manual

Good Earth IN_AC1347-CCT-07LF0-G LED USB Tape Light

Product Information

The 7 ft LED USB Tape Light CCT w/ IR Remote is a non-curable and non-linkable tape light that can be connected to televisions, laptop computers, or electrical outlets with a USB power adapter (not included). The tape light comes with a hardware kit, CT controller, receptor IR (Infrarrojo), and safety glasses. The LED tape light is intended for indoor locations only, and it is not expandable. Additional LED tape light lengths cannot be added. The tape light must be fully uncoiled for proper operation and to prevent overheating. The tape light should not be installed over sinks or stoves and is not intended for recessed installation in ceilings or soffits. Additionally, cords should not be run behind walls, ceilings, soffits, cabinets, or any similar permanent structure where it may be inaccessible for examination. It is recommended to use insulated staples or plastic ties to secure the cords and to avoid using an extension cord. A power strip with integral over current protection should be used to supply power to the fixture. The LED tape light gradually emits less light over its lifetime, and it should not be used with a dimming circuit. If dimmer controls are present, they should be removed and replaced.

Product Usage Instructions

1. Before first use, orient the label side of the IR receiver with the LED side of the tape. The red arrow should match with the +5V on the LED side of the tape.
2. Select a location for the LED tape light and mark it. Verify that the USB cord reaches the nearest USB port. Thoroughly clean the mounting surface with rubbing alcohol and allow it to dry. Remove the backing liner carefully so as to not accidentally peel away the mounting glue of the LED tape light. Place the LED tape light in the desired position. Once in place, allow the tape adhesive to cure for 24 hours before use.
3. Once the LED tape lights are firmly in place, plug the USB connector into a television, computer laptop, or USB adaptor.

It is important to read the entire manual prior to installation, and no parts are serviceable on this product. The LED tape lightsare non-cutable and non- linkable, and they should not be altered or touched while in contact with water. This product is not intended for illumination of aquariums. If unfamiliar with electrical installations, contact a qualified electrician to install. DO NOT INSTALL WHILE UNIT IS PLUGGED IN.

Hardware kit

Required

SAFETY INFORMATION

THIS LIGHT IS NON-CUTTABLE AND NON-LINKABLE
This product has a USB connector allowing quick and easy connection to televisions and laptop computers. The LED tape lights can also be plugged into an electrical outlet with a USB power adapter (not included). DO NOT ALTER THE TAPE LIGHT. READ THE ENTIRE MANUAL PRIOR TO INSTALLATION. Verify package and hardware contents. Save these instructions.

ATTENTION

• No parts are serviceable on this product. DO NOT cut the LED tape lights. These LED tape lights are non cuttable and non linkable.
• For electrical requirements, see back of driver label.
• For INDOOR locations only.
• This tape light is NOT expandable. Additional LED tape light lengths CANNOT be added.
• Use only insulated staples or plastic ties (not included) to secure the cords.
• DO NOT use with an extension cord. Use a power strip with integral over current protection to supply power to the fixture. NEVER use power strip unless the plug can be fully inserted.
• LEDs gradually emit less light over their lifetime.

WARNING

• DO NOT INSTALL WHILE UNIT IS PLUGGED IN.
• DO NOT plug the USB cord into the power source until installation is complete
• DO NOT touch, operate, or install fixture while in contact with water. Not intended for illumination of aquariums.
• DO NOT look directly at lighted LEDs for any length of time.
• DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT. If dimmer controls are present, remove and replace.
• If unfamiliar with electrical installations, contact a qualified electrician to install.

CAUTION

• DO NOT mount over sinks or stoves.
• NOT intended for recessed installation in ceilings or softs. DO NOT run ANY cords behind walls, ceilings, softs, cabinets or a similar permanent structure where it may be inaccessible for examination.
• Tape light must be fully uncoiled for proper operation, and to prevent overheating.

INSTALLATION

Attaching the IR reciever to the LED Tape light

1. Before first use, orient label side of IR Receiver with LED side of tape. The red arrow should match with the +5V on LED side of the tape.
   Attaching Tape Light to Surface

2. Select a location for the LED tape light and mark it. Verify that the USB cord reaches the nearest USB port. Thoroughly clean the mounting surface with rubbing alcohol and allow it to dry. DO NOT PLUG THE USB CORD INTO THE POWER SOURCE UNTIL INSTALLATION IS COMPLETE. Remove the backing liner carefully so as to not accidentally peel away the mounting glue of the LED tape light. Place the LED tape light in the desired position. Carefully apply pressure to the entire length of the LED tape light to ensure proper adhesion.
   Do not reposition tape light once it is mounted. Doing so will reduce the adhesiveness of the tape backing.
   Once in place, allow the tape adhesive to cure for 24 hours before use.
   Connecting USB Cord

3. Once the LED tape lights are firmly in place, plug the USB connector into a television, computer laptop, or USB adaptor.

REMOTE CONTROLS

1. Remove the plastic battery tab on the remote control by pulling it straight out of the remote.
2. The maximum operating distance of the remote control with new batteries is approximately 15 ft. (5 m) with a direct line of sight between the remote control and the IR receiver.
3. The battery used in the remote control is a CR2025 button cell, and will need to be replaced at the end of its life cycle.
   NOTE: Remote controller operation requires direct line of sight between the remote control and the IR receiver within 15ft.

BATTERY REPLACEMENT
When the battery is exhausted, use the instructions on the back of the remote control to remove the battery and replace it with a new CR2025 battery.
Swallowing the batteries may lead to serious injury or death. If swallowed, go straight to a medical emergency room. Batteries may leak harmful liquids or ignitable materials or explode causing injury and product damage. Do not mix old and new, or different types of batteries. Replace all batteries at the same time. Remove batteries from product if unused for extended amount of time. Replaced batteries should be disposed of properly. Keep batteries out of children’s reach.

TROUBLESHOOTING GUIDE

DANGER! BEFORE DOING ANY WORK ON THE FIXTURE, UNPLUG THE POWER CORD FROM THE ELECTRICAL OUTLET!

on.
2. IR Receiver blocked from remote control signal.| 2. Position IR Receiver facing the direction of the remote
Light will not switch colors when remote is used.| 1. Remote not functioning correctly.| 1. Clean IR lens on remote
2. IR Receiver not receiving remote light.| 2. Pull plastic tab from battery compartment or replace battery (CR2025)
LED strip adhesive is losing adhesion.| 1. Mounted on unfinished wood or particle board surfaces.| 1. Mount with brackets and screws (not included).
2. Surface is not wiped down.| 2. Clean surface and reapply new layer of double- sided tape such as 3M VHB (not included).

6-YEAR LIMITED WARRANTY

Good Earth Lighting® – The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (6) years from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to ship your defective product.
Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs, or injury which is caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage, labor costs, or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.

FCC STATEMENT

“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Caution: Changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC responsible party name: Good Earth Lighting Inc.
Address: 1400 E Business Center Drive, STE 108 Mount Prospect, IL 60056 USA.
Telephone number: 1-800-291-8838

Need Help?
Please visit our website at: https://goodearthlighting.com/contact-us or call the Customer Care Center at 1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday. Printed in Thailand

Good Earth Lighting® 1400 East Business Center Drive, Ste. 108 Mount
Prospect, IL 60056
Good Earth Lighting® is a registered trademark of Good Earth Lighting, Inc.
© 2022 Good Earth Lighting, Inc. REV08.22

References

• Contact Us | Good Earth Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>