sw-motech FRS.08.011.10201-S KLR 650 Ion Kawasaki Footpegs Installation Guide
- June 1, 2024
- SW-MOTECH
Table of Contents
ANBAUANLEITUNG
mounting instructions
FRS.08.011.10201/S
contains
FRS.08.011.80201/S
FRS.00.011.10000/S
FRS.08.011.10201/S
Revision: 00
Footrest Kit
KAWASAKI KLR 650 & HONDA XL 650 V
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg
Germany
Tel. +49 (0) 64 25/8 16 8-00
Fax +49 (0) 64 25/8 16 8-10
info@sw-motech.com
www.sw-motech.com
Mounting Instructions
SW-MOTECH products should be installed by a qualified, experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. SW Motech takes no responsibility for damages caused by improper installation.
All screws, bolts and nuts, including all replacement hardware provided by SW- MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used:
M6|
9,6 Nm
---|---
M8|
23 Nm
All screws, bolts and nuts should be checked after driving the first 50 km to ensure that all are tightened to the proper torque.
1 Footrest 2 Rubber Pad
FRS.00.011.001 FRS.00.011.002
Pcs. 2 Pcs. 2
3 Hexagon Screw 4 Washer
M6 x 10 DIN 933 A 6,4 DIN 125
Pcs. 2 Pcs. 2
FRS.00.011.10000/S
5 Hinge Adapter 6 Hexagon Screw
FRS.08.011.A82 M8 x 16 DIN 933
Pcs. 2 (L/R) Pcs. 2
7 Washer 8 Hinge Spring
300 HV
A8,4 DIN 9021 FRS.00.011.004
Pcs. 2 Pcs. 2
9 Plastic Cap
KEK.00.M6.ISK
Pcs. 2
FRS.08.011.80201/S
ATTENTION
Attention: Cornering and ground clearance can be reduced by using this
accessory.
INFORMATION
Before removing the original footrests Please make sure to note the order
and direction of the original fixing parts. These parts will be needed for
mounting the SW-MOTECH footrests in the same order and direction.
ATTENTION
Use medium strength thread locker (Loctite) to secure ALL screws.
INFORMATION
Use the original fixing parts (pins, etc.) for mounting the SW-MOTECH
footrests at the shown positions on both sides of the motorcycle. Make sure to
mount the parts the same way as with the original footrests.
! Example footrest mount shown!
Driving Direction
- Position for original footrest height.
FRS.00.011.10000/S
Revision: 01
Footrests
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg
Germany
Tel. +49 (0) 64 25/8 16 8-00
Fax +49 (0) 64 25/8 16 8-10
info@sw-motech.com
www.sw-motech.com
Mounting Instructions
SW-MOTECH products should be installed by a qualified, experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. SW Motech takes no responsibility for damages caused by improper installation.
All screws, bolts and nuts, including all replacement hardware provided by SW- MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used:
M6|
9,6 Nm
---|---
All screws, bolts and nuts should be checked after driving the first 50 km to ensure that all are tightened to the proper torque.
Medium strength liquid thread-locker (i.e., “Locktite”) should be used to secure all screws, bolts and nuts.
ATTENTION
Attention: Cornering and ground clearance can be reduced by using
this accessory.
1 Footrest 2 Rubber Pad
FRS.00.011.001 FRS.00.011.002
Pcs. 2 Pcs. 2
3 Hexagon Screw 4 Washer
M6 x 10 DIN 933 A 6,4 DIN 125
Pcs. 2 Pcs. 2
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>