DORMAN 740-609 Rear Passenger Side Power Window Regulator Instruction Manual

: June 1, 2024
: DORMAN

Table of Contents

DORMAN 740-609 Rear Passenger Side Power Window Regulator
Product Information
Product Usage Instructions
Frequently Asked Questions
Tools required
Removal Instructions
Installation Instructions
Contact
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DORMAN 740-609 Rear Passenger Side Power Window Regulator

DORMAN-740-609-Rear-Passenger-Side-Power-Window-Regulator-
product

Product Information

Specifications:

Product Code: 740-609
Product Type: Window Regulator
Tools Required: Trim panel removal tool, small flat-blade
screwdriver, Phillips head screwdriver
Recommended Safety Gear: Safety glasses

Product Usage Instructions

Removal Instructions:

Step 1: Using a trim panel removal tool,\ remove the screw covers that retain the interior door trim panel.
Step 1a: Remove the door cup handle retaining screw.
Step 2: Using a trim panel removal tool, remove the door switch assembly.
Step 3: Disconnect the door switch assembly.
Step 4: Using either a trim panel removal tool or small flat-blade screwdriver, remove the interior door handle bezel assembly.
Step 5: Using a trim panel removal tool, release the interior door trim panel from the door.
Step 6: Pull the interior door trim panel toward you and lift in an upward motion to remove it.
Step 6a: Remove the interior door trim panel support bracket using a Phillips head screwdriver.
Step 7: Remove the water vapor barrier.
Step 8: Temporarily install the door switch to lower the window glass and expose the window regulator attaching screws.

Frequently Asked Questions

Q: Do I need any special tools for installing the window\ regulator?
- A: Yes, you will need a trim panel removal tool, small flat-blade screwdriver, and a Phillips head screwdriver for installation.
Q: Can I install the window regulator myself if I don’t have a service manual?
- A: It is recommended to refer to the appropriate shop manual for your vehicle for specific service procedures. If you lack the skill or manual, it’s best to seek the help of a qualified technician.
Q: What should I do if I encounter difficulties during installation?
- A: If you face challenges during installation, stop and seek professional assistance. It’s crucial to follow all instructions carefully to avoid any damage or safety risks.

ATTENTION:

Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualifi ed technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.

REMOVAL/INSTALL OF WINDOW REGULATOR (740-609) \Nissan Sentra 1995–99

General Tech Tips:

Use painter’s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue.
A plastic pry tool is useful. It will not easily damage delicate trim like a screwdriver or metal pry bar.
The replacement regulator should have a liberal amount of grease on slide area. If there is not much grease present, white lithium grease works well to lubricate the slide area.
Aftermarket window tinting can cause the window to travel slower and put additional strain on the window regulator assembly.
Window run channels should be cleaned and lubricated before installation of a new window regulator assembly. Silicone spray works well.

Tools required

Tools required for removal and installation of window regulator and motor assembly:

Silicone spray lubricant
Trim panel removal tool
Pick
Saddle cup assembly, tape, or wedge to hold window in place
Flat-blade screwdriver or plastic pry tool
10mm socket or driver
Phillips screwdriver
Grease pencil or marker

Removal Instructions

STEP 1: Using a trim panel removal tool, remove the screw covers that retain the interior door trim panel.
STEP 1a: Remove the door cup handle retaining screw.
STEP 2: Using a trim panel removal tool, remove the door switch assembly
STEP 3: Disconnect the door switch assembly.
STEP 4: Using either a trim panel removal tool or small fl at-blade screwdriver, remove the interior door handle bezel assembly.
STEP 5: Using a trim panel removal tool, place the tool between the door and the interior door trim panel and using fi rm, even pressure release the interior door trim panel from the door.
STEP 6: To remove the interior door trim panel, pull the interior door trim panel toward you and lift in an upward motion.
STEP 6a: Using a Phillips head screwdriver, remove the interior door trim panel support bracket.
STEP 7: Remove the water vapor barrier.
STEP 8: Temporarily install the door switch to lower the window glass exposing the window glass to window regulator attaching screws. NOTE: There are two (2) screws that attach the door glass to the window regulator
STEP 9: Once the window glass has been disconnected from the window regulator, manually slide the window glass into the closed position and hold in place with either a saddle cup assembly, painters tape, or a wedge
STEP 10: Disconnect the window lift motor connector.
STEP 11: Using your ratchet with a 10 mm socket, remove the four screws that attach to the window regulator assembly
STEP 12: Using your ratchet with a 10 mm\ socket, remove the three screws that attach the window lift motor.
STEP 13: Remove the window regulator assembly through the main access hole.
NOTE: At this point, your interior door trim panel reinforcement bracket would be removed.
STEP 14: Remove the three (3) window lift motor attaching screws.

Installation Instructions

STEP 1: Attach the three (3) window lift motor attaching screws.
STEP 1a: Place the window regulator through the main access hole. Once the window regulator assembly is placed into position, loosely mount the window regulator assembly with its attaching hardware.
STEP 3: Using your ratchet with a 10 mm socket, tighten down the window regulator attaching hardware.
STEP 4: Tighten down the window lift motor attaching hardware
STEP 5: Manually slide the window glass onto the window regulator. NOTE: It may be necessary to temporarily connect the master power switch assembly to align the window glass to the window regulator.
STEP 6: At this point, verify that the window regulator is operating properly. Once this has been verifi ed, disconnect the power master switch assembly.
STEP 7: Install the water vapor barrier.
STEP 8: Attach the interior door trim panel reinforcement bar.
STEP 9: Install the interior door trim panel. NOTE: When installing the interior door trim panel, pull the door trim panel in a downward motion. Be sure to align the door trim \panel on the lip of the door and align the interior door trim panel retaining hardware with its corresponding holes. Once everything is aligned, press the interior door trim panel into position.
STEP 10: Connect the power door switch connector.
STEP 11: Attach the power door switch assembly onto the interior door trim panel.
STEP 11a: Attach the door cup pull attaching screw.
STEP 12: Attach the interior door trim panel attaching screws.
STEP 13: Verify that all of the interior door trim panel attaching hardware is secure and that the window regulator is operating properly.
STEP 14: Attach the interior door handle bezel

Contact

We appreciate your opinions regarding this product! Please call our Technical Assistant with any challenges or suggestions regarding the installation or operation of this product. 1-800-523-2492

Disclaimer:

Even though every attempt is made to ensure this information is complete and accurate, it is impossible to account for all possible circumstances or situations. Please consult with a qualifi ed auto technician before attempting to perform any work you are not qualifi ed to do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor Vehicle Safety Standards by the National Highway Traffi Safety Administration). Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature. ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualifi ed technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully. 11 ©2012 Dorman Products, Inc. No reproductions in whole or in part without prior written approval.