Dorman 600-904 Transfer Case Motor Instruction Manual
- June 1, 2024
- DORMAN
Table of Contents
600-904
DIAGNOSTIC TROUBLE CODES: TRANSFER CASE MOTOR
600-904 Transfer Case Motor
ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully.
2007–04 Buick Ranier, 2004–02 Oldsmobile Bravada, 2009–05 Saab 9-7X, 2009–03 Trailblazer/Envoy
DTC-C0306: Motor A or B Circuit Failure
Description:
Diagnostic Trouble Code C0306 is set once the Transfer Case Control Module
detects an open, short-to-ground, or low voltage in the Motor Control A or B
circuit, or an open or short-to-ground fault inside of the transfer case
motor.
How to access the diagnostic trouble code (DTC):
Once there has been a DTC set, the vehicle will either set a “service soon”
light, or the lights on the 4×4 switch will flash and/or stay lit. To access
the DTCs, you will need to hook up a vehicle diagnostic scanner utilizing the
service port under the driver side portion of the dash.
When to clear a DTC:
The diagnostic trouble code (DTC) should only be erased once the positive
voltage concern has been corrected.
How to clear a DTC:
- The Transfer Case Control Module (TCCM) will clear the DTC once the initial problem has been fi xed.
- A hard DTC will clear once the vehicle has run through one hundred (100) start cycles and detects no faults.
- To clear the DTC manually, you will need a vehicle diagnostic scanner (Scan tool). Once the DTC has been erased, go back into the vehicle system and verify that the DTC has been erased and that the system is performing properly.
DTC-C0327:
Description:
DTC-C0327 will be set when the Transfer Case Control Module (TCCM) receives
both high and low voltage on the encoder channel circuits.
What causes DTC-C0310:
DTC-C0310 will set when the Transfer Case Control Module (TCCM) detects a
variation in voltage from an encoder circuit. The encoder circuit is telling
the TCCM what position (gear) the Transfer case is in. If the Transfer case is
in a predetermined position (gear) and returns the incorrect value (voltage),
the TCCM will set DTC-C0327. A faulty transfer case shift shaft can cause
DTC-C0327. Be sure to check the lateral and vertical movement of the transfer
case shift shaft.
How to access the diagnostic trouble code (DTC):
Once there has been a DTC set, the vehicle will either set a Service 4WD light
or the lights on the 4×4 switch will flash and/or stay lit. To access the
DTCs, you will need to hook up a vehicle diagnostic scanner utilizing the
service port under the driver side portion of the dash.
When to clear a DTC:
The diagnostic trouble code (DTC) should only be erased once the voltage
concern has been corrected, or the mechanical problem has been addressed.
How to clear a DTC:
- The Transfer Case Control Module (TCCM) will clear the DTC once the initial problem has been fi xed.
- A hard DTC will clear once the vehicle has run through one hundred (100) start cycles and detects no faults.
- To clear the DTC manually, you will need a vehicle diagnostic scanner (Scan tool). Once the DTC has been erased, go back into the vehicle system and verify that the DTC has been erased and that the system is performing properly.
DTC-C0374: General 4WD Failure
Description:
DTC-C0374 will be set when the Transfer Case Control Module (TCCM) detects
rear wheel slippage. Once the TCCM attempts to apply torque to the front
wheels and cannot, DTC-C0374 will be set. When DTC-C0374 is activated, you
will not be able to use your AUTO 4WD. The “SERVICE 4WD” light will remain on
until you re-start your vehicle.
What causes DTC-C0374:
DTC-C0374 will set when the Transfer Case Control Module detects a variation
in the front drive shaft and rear drive shaft speed sensor, and is not able to
engage the front differential after ten (10) unsuccessful attempts.
How to access the diagnostic trouble code (DTC):
Once there has been a DTC set, the vehicle will either set a “Service 4WD”
light, or the lights on the 4×4 switch will flash and/or stay lit. To access
the DTCs, you will need to hook up a vehicle diagnostic scanner utilizing the
service port under the driver side portion of the dash.
When to clear a DTC:
The diagnostic trouble code (DTC) should only be erased once the voltage
concern has been corrected, or the mechanical problem has been addressed.
How to clear a DTC:
- The Transfer Case Control Module (TCCM) will clear the DTC once the initial problem has been fixed.
- A hard DTC will clear once the vehicle has run through one hundred (100) start cycles and detects no faults.
- To clear the DTC manually, you will need a vehicle diagnostic scanner (Scan tool). Once the DTC has been erased, go back into the vehicle system and verify that the DTC has been erased and that the system is performing properly.
Disclaimer:
Even though every attempt is made to ensure this information is complete and
accurate, it is impossible to account for all possible circumstances or
situations. Please consult with a qualified auto technician before attempting
to perform any work you are not qualified to do. Automobiles can be hazardous
to work on; be sure to take all necessary safety precautions. Failure to do so
may result in property damage or personal injury. Certain motor vehicle
standards and performance requirements may apply to your motor vehicle (such
as Federal Motor Vehicle Safety Standards by the National Highway Traffic
Safety Administration). Be sure that your work is performed in accordance with
such standards and that you do not disable any motor vehicle safety feature.
©2012 Dorman Products, Inc.
No reproductions in whole or in part without prior written approval.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>