FORESiGHT SPORTS JODY W263 Host Based Multiradio Module with WiFi and Bluetooth 5 Instructions

June 5, 2024
FORESiGHT SPORTS

FORESiGHT logo

JODY-W263
Host-based multiradio module with Wi-Fi and Bluetooth 5
Integration Instructions

Abstract
This document describes the system integration of the JODY-W263 module into a host product. These host-based modules support Wi-Fi 802.11n/ac and Bluetooth® 5 and is designed for both simultaneous and independent operations. The JODY-W263 module includes an integrated MAC/baseband processor and RF front- end components. This document is to only be used internally for Foresight Sports, as the grant pertaining to this module is not intended for the distribution of the module.

Document Information

Title JODY-W2
Subtitle Host-based multiradio modules with Wi-Fi and Bluetooth 5
Document type Integration Instructions
Document name FSS JODY-W263 System integration manual
Revision and date Rev 0119-May-22
Disclosure restriction Confidential

This document applies to the following products.
Product name
JODY-W263-00B

List of applicable FCC rules

The following FCC rules are applicable to the equipment:

  • CFR 47, Part 15, Subpart C
  • CFR 47, Part 2, Subpart J – Radiofrequency radiation exposure: portable devices

2 Summary of operational use conditions

2.1 Antenna Configuration and Gain
2.1.1 Antenna Configuration

2.1.1 Antenna Configuration
In addition to the general requirement to use only authorized antennas, the grant also requires a separation distance of at least 20 cm from the antenna(s) to all persons. The antenna(s) must not be co-located with any other antenna or transmitter (simultaneous transmission) as well. If this cannot be met, a Permissive Change as described below must be made to the grant.
In order to support verification activities that may be required by certification laboratories, customers applying for Class-II Permissive changes must implement the setup described in Radio Test Guide for NXP-based modules.
If the module is to be co-located with another transmitter, additional measurements for simultaneous transmission are required. The results must be added to the grant file as a  Class II Permissive Change.
If the authorized antennas and/or antenna trace design cannot be used, the new antenna and/or antenna trace designs must be added to the grant file. This is done by a Class I  Permissive Change or a Class II Permissive Change, depending on the specific antenna and antenna trace design.

  •  Antennas of the same type and with less or same gain as an already approved antenna can be added under a Class I Permissive Change.
  • Antenna trace designs deviating from the reference design and new antenna types are added under a Class II Permissive Change.
  • For 5 GHz modules, the combined minimum gain of antenna trace and antenna must be greater than 0 dBi to comply with DFS testing requirements.

2.1.2 Antenna Gain
The antenna gain in each band must not exceed the following:
Wi-Fi Output Power for 2.4GHz band

Channel

|

Modulation

| Channel

bandwidth

|

Data rates

| Maximum power

setting

---|---|---|---|---
1 – 11| CCK and DSSS| 20 MHz| 1, 2, 5.5, 11 Mbps| 12 dBm
1| OFDM| 20 MHz| 6, 9, 12, 18, 24, 36, 48, 54 Mbps| 11 dBm
2 – 10| OFDM| 20 MHz| 6, 9, 12, 18, 24, 36, 48, 54 Mbps| 16 dBm
11| OFDM| 20 MHz| 6, 9, 12, 18, 24, 36, 48, 54 Mbps| 11 dBm
1| OFDM| 20 MHz| HT20 MCS0-MCS7| 11 dBm
2 – 10| OFDM| 20 MHz| HT20 MCS0-MCS7| 16 dBm
11| OFDM| 20 MHz| HT20 MCS0-MCS7| 11 dBm
3| OFDM| 40 MHz| HT40 MCS0-MCS7| 11 dBm
4 – 8| OFDM| 40 MHz| HT40 MCS0-MCS7| 16 dBm
9| OFDM| 40 MHz| HT40 MCS0-MCS7| 11 dBm

Table 1: Wi-Fi power table for operation in the 2.4 GHz band

Wi-Fi Output power for 5 GHz band

Channel

|

Modulation

| Channel

bandwidth

|

Data rates

| Maximum power

setting

---|---|---|---|---
36 – 64| OFDM| 20 MHz| 6, 9, 12, 18, 24, 36, 48, 54 Mbps| 15 dBm
36 – 64| OFDM| 20 MHz| HT20 MCS0-MCS7| 15 dBm
36 – 64| OFDM| 20 MHz| VHT20 MCS0-MCS8| 15 dBm
38 – 62| OFDM| 40 MHz| HT40 MCS0-MCS7| 15 dBm
38 – 62| OFDM| 40 MHz| VHT40 MCS0-MCS9| 15 dBm
42| OFDM| 80 MHz| VHT80 MCS0-MCS9| 14 dBm

Table 2: Wi-Fi power table for operation in the 5 GHz U-NII-1 and U-NII-2A bands


Channel

| ****

Modulation

| Channel

bandwidth

| ****

Data rates

| Maximum power

setting

---|---|---|---|---
100 – 144| OFDM| 20 MHz| 6, 9, 12, 18, 24, 36, 48, 54 Mbps| 15 dBm
100 – 144| OFDM| 20 MHz| HT20 MCS0-MCS7| 15 dBm
100 – 144| OFDM| 20 MHz| VHT20 MCS0-MCS8| 15 dBm
102| OFDM| 40 MHz| HT40 MCS0-MCS7| 14 dBm
102| OFDM| 40 MHz| VHT40 MCS0-MCS9| 14 dBm
110-142| OFDM| 40 MHz| HT40 MCS0-MCS7| 15 dBm
110-142| OFDM| 40 MHz| VHT40 MCS0-MCS9| 15 dBm
106 – 138| OFDM| 80 MHz| VHT80 MCS0-MCS9| 14 dBm

Table 4: Wi-Fi power table for operation in the 5 GHz U-NII-3 band

2.2 Co-location
If the module is to be co-located with another transmitter, additional measurements for simultaneous transmission are required. The results must be added to the grant file as a
Class II Permissive Change.
The module is not currently approved for co-location with any other modules.

 RF Exposure conditions

3.1 Installation Instructions
The module is approved for use in a mobile RF exposure environment. A minimum separation distance of 20 cm must be maintained between the antenna and nearby persons.
The module is not approved for co-location with any other modules.

3.2 Warning
A warning must be placed in the host product user instructions stating that:

  1. This device is approved for use in a mobile rf exposure environment. A minimum separation distance of 20 cm must be maintained between the antenna and nearby persons.”
  2. The module is not approved for co-location with any other modules.
    The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with he FCC requirements by a technical assessment or evaluation to the FCC rules and KDB Publication 996369.
    If the required separation distance of 20 cm cannot be fulfilled, a SAR evaluation must be performed. This consists of additional calculations and/or measurements. The result must be added to the grant file as a Class II Permissive Change.

Approved Antennas:

The antenna should be installed and operated with a minimum distance of 20 cm between the radiator and nearby persons.
See Antenna Gain for limits by the band

Antenna(s) approved for Wi-Fi

Brand| Model| Type| Antenna Gain in 2.4 GHz band| Antenna Gain in 5 GHz band
---|---|---|---|---
Pulse| W3006| Chip| 2.2dBi| 5.2dBi

Antenna(s) approved for Bluetooth

Brand| Model| Type| Antenna Gain in 2.4 GHz band| Antenna Gain in 5 GHz band
---|---|---|---|---
Pulse| W3006| Chip| 2.2dBi| 5.2dBi

Label and Compliance Information

5.1 Label requirements
5.1.1 United States (FCC)
This section contains the FCC compliance information for the JODY-W263-00B series modules.

Model ISED certification number
JODY-W263-00B 28505-JODYW263FSS

JODY-W263-00B
28505-JODYW263FSS
5.1.2 FCC Compliance statement
JODY-W263 module has modular approval and complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications NOT explicitly APPROVED could cause the JODY-W263 module to cease to comply with FCC rules part 15 thus voiding the user’s authority to operate the equipment.
The internal/external antenna(s) used for this module must provide a separation distance of at least20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.
In accordance with 47 CFR § 15.19, the end product into which this module is integrated bears the following statement in a conspicuous location on the device:

“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2.  This device must accept any interference received, including interference that may cause undesired operation.”

When the end-product is so small or for such use that it is not practical to place the above statement on it, the information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or on the container in which the device is marketed. However, the FCC ID label must be displayed on the device.
If the end-product will be installed in locations where the end-user is not able to see the FCC ID and/or this statement, the FCC ID and the statement shall also be included in the end-product manual.
 The outside of final products containing the JODY-W2 module must display in a user-accessible area a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2A6QA-JODYW263FSS” or “Contains FCC ID: 2A6QA-JODYW263FSS”.
5.1.3 Canada (ISED)
JODY-W2 series modules are certified for use in accordance with the Canada Innovation, Science and Economic Development Canada (ISED) Radio Standards Specification  RSS) RSS-247 Issue 2 and RSSGen. Below is the list of the ISED IDs allocated to the JODY-W263 module.

5.1.4 ISED compliance statement
JODY-W263-00B module complies with ISED (Innovation, Science and Economic Development Canada) license-exempt RSS. Operation is subject to the following two conditions:

  1. This device may not cause interference, and
  2. This device must accept any interference, including interference that may cause undesired
    operation of the device.

Any notification to the end user of installation or removal instructions about the integrated radio module is NOT allowed. Unauthorized modification could void the authority to use this equipment
This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
This radio transmitter IC: 28505-JODYW263FSS has been approved by ISED to operate with the antenna types listed below with the maximum permissible gain indicated.  Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
Operation in the 5600-5650 MHz band is not allowed in Canada. High-power radars are allocated as primary users (i.e., priority users) of the bands 5250-5350 MHz and  5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices. The ISED certification label of a module shall be clearly visible at all times when installed in the host device; otherwise, the host device must be labeled to display the ISED certification number for the module, preceded by the words “Contains transmitter module”, or the word “Contains”, or similar wording expressing the same meaning, as follows: “Contains transmitter module IC: 28505-JODYW263FSS”.
This radio transmitter IC: 28505-JODYW263FSS has been approved by ISED to operate with the antenna types listed below with the maximum permissible gain indicated.  antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
The internal/external antenna(s) used for this module must provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.
The approval type for all JODY-W2 series variants is a single modular approval. Due to ISED Modular Approval Requirements (Source: RSP-100 Issue 10), any application which includes the module must be approved by the module manufacturer (u-blox). The application manufacturer must provide design data for the review procedure.

Information on test modes and additional test

For end host implementation the user must refer to the manufacturer integration manual to implement software/firmware that can be used to manipulate the module configuration and put it into special test modes, set and verify regional power limits, and any debugging required.

Additional test requirements

Foresight Sports warrants that the modular transmitter fulfills the FCC/ISED regulations when operating in authorized modes on any hosting product given that the integrator follows the instructions as described in this document.

The modular transmitter approval of JODY-W263, or any other radio module, does not exempt the end product from being evaluated against applicable regulatory demands.

The evaluation of the end product shall be performed with the JODY-W263 module installed and operating in a way that reflects the intended end product use case. The upper-frequency measurement range of the end product evaluation is the 10th harmonic of 5.8 GHz as described in KDB 996369 D04.
The following requirements apply to all  products that integrate a radio module:

  • Subpart B – UNINTENTIONAL RADIATORS
    To verify that the composite device of host and module complies with the requirements of FCC part 15B, the integrator shall perform sufficient measurements using ANSI 63.4-2014.

  • Subpart C – INTENTIONAL RADIATORS
    To validate that the fundamental and out-of-band emissions of the transmitter part of the composite device comply with the requirements of FCC part 15C, it is required that the integrator carries out sufficient verification measurements using ANSI 63.10-2013.

Revisions

Revision| Description| Date| Author
01| Initial Release| 19 May 2022| P. Hicks

Document Information
FSS JODY-W263 Integration Instructions
www.foresightsports.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals