BOGEN SPT15A 15-30 Watt Horn Loudspeakers Installation Guide
- June 6, 2024
- BOGEN
Table of Contents
BOGEN SPT15A 15-30 Watt Horn Loudspeakers
Installation Instructions
STEP 1 – For easier installation, remove the mounting base from the
speaker by unscrewing the wing nut while at the same time pressing inwardly
on the wing nut. Place the mounting base flush on the mounting surface and
mark the location of the three holes with either a marker or chisel. It is
important that the three holes be exactly aligned with the mounting base,
otherwise you might stress the base or make the connection unsteady. Use
appropriate hardware for your specific mounting surface.
NOTE: Speaker may also be strap-mounted through the slot in mounting base
using standard 1/2-inch industrial strapping (not included).
Figure 1. Mounting Base and
Strap Mounting Slot
STEP 2 – After mounting the base, reattach the speaker and aim the speaker for the desired coverage angle. A 45° downward angle is recommended, but this may vary depending upon speaker layout. Unless otherwise indicated, do not aim speakers directly at each other or poor paging intelligibility may occur.
STEP 3 – Remove the plastic cover to expose the connecting screws (see
Figure 2). Strip the ends of the connecting wires about 1/4″ and connect them
to the terminals. The terminals are numbered to indicate phasing.
Provide cable strain relief by laying the cables within the recess on the
casting and holding it tight with the plastic cover. The narrow recess is for
two-conductor cable; the wide recess is for shielded cable.
Figure 2. Tap Set Control and
Connecting Screw Terminals (SPT15A/SPT30A only)
Connect wires as listed below:
Amplifier Output
|
Speaker Connections
---|---
70V, 25V, or 8 ohms
|
Terminal 1
COM
|
Terminal 2
NOTE: These are recommended connections. The speaker will also work perfectly well with these connections reversed, but be consistent in wiring connections.
STEP 4 – Adjust the tap set control to the desired setting. See table (Figure 3 on next page) for tap settings and sound pressure levels for the different horn loudspeakers. Replace the plastic protective cover back over the exposed area.
|
SPT15A
|
SPT30A
---|---|---
|
@25V
| @70V| @25V|
@70V
Tap Set|
Watts
| dBspl| Watts| dBspl| Watts| dBspl*| Watts|
dBspl*
1
| | | 0.9| 109| | | 1.8| 113
2| | | 1.8| 112| | | 3.7|
116
3
| 0.48| 106| 3.8| 118| | | 7.5| 119
4| 0.94| 109| 7.5| 121| 1.8| 113| 15.0|
122
5
| 1.8| 112| 15.0| 121| 3.7| 116| 30.0| 125
6| 7.5| 118| | | 7.5| 119| |
7
| 15.0| 121| | | 15.0| 122| |
8| Not Used| Not Used| Not Used|
Not Used
Technical Specifications
|
SP158A
| SPT15A| SP308A|
SPT30A
---|---|---|---|---
Power Rating (RMS)
|
15 watts continuous, 20 watts equalized
|
30 watts continuous, 40 watts equalized
Frequency Response
|
275Hz to 14kHz
|
225Hz to 14kHz
Impedance
|
8 ohms
| 25/70 volts| 8 ohms|
25/70 volts
Sound Pressure Level
|
121dB@ 4 feet on axis with 15 watt input@ 1000Hz
|
125dB@ 4 feet on axis with 30 watt input@ 1000Hz
Dispersion
|
110°
|
100°
Dimensions
|
9″ Diameter x 9-1/4″ D
|
11″ Diameter x 10-1/2″ D
Shipping Weight
|
4 lb.
| 4-1/2 lb.| 6 lb.|
6 lb.
Finish
|
Textured mocha enamel
LIMITED WARRANTY; EXCLUSION OF CERTAIN DAMAGES
The Bogen SP158A, SPT15A, SP308A, and SPT30A Horn Speakers are warranted
to be free from defects in material and workmanship from the date of sale to
the original purchaser for the lifetime of the products. Any part of the
product covered by this warranty that, with normal installation and use,
becomes defective (as confirmed by Bogen upon inspection) during the
applicable warranty period, will be repaired or replaced by Bogen, at Bogen’s
option, provided the product is shipped insured and prepaid to: Bogen Factory
Service Department: 4570 Shelby Air Drive, Suite 11, Memphis, TN 38118, USA.
Repaired or replacement product will be returned to you freight prepaid. This
war ranty does not extend to any of our products that have been subjected to
abuse, misuse, improper storage, neglect, accident, improper instal lation or
have been modified or repaired or altered in any manner whatsoever, or where
the serial number or date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND
THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF
ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND
EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen’s liability
arising out of the manufacture, sale or supplying of products or their use or
disposition, whether based upon warranty, contract, tort or otherwise, shall
be limited to the price of the product. IN NO EVENT SHALL BOGEN BE
LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS OF USE DAMAGES) ARISING OUT
OF THE MANUFACTURE, SALE OR SUPPLYING OF PROD UCTS, EVEN IF BOGEN HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some States do not
allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from
State to State.
Products that are out of warranty will also be repaired by the Bogen Factory
Service Department – same address as above or call 201-934- 8500. The parts
and labor involved in these repairs are warranted for 90 days when repaired by
the Bogen Factory Service Department. All shipping charges in addition to
parts and labor charges will be at the owner’s expense. All returns require a
Return Authorization number. For most efficient warranty or repair service,
please include a description of the failure.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>