SW-MOTECH BC.HTA.01.682.20300 Motorcycle Saddle Bag Instruction Manual
- June 1, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.HTA.01.682.20300 Motorcycle Saddle Bag
Specifications
- Model Numbers: HTA.01.682.10200, HTA.01.682.11100, BC.HTA.00.682.11100, BC.HTA.00.682.11000, BC.LOC.00.682.10000/S
- Product Code: BC.HTA.01.682.20300
Installation
Follow the ANBAUANLEITUNG guide provided to correctly install the product.
Operation
Ensure all connections are secure before use. Refer to the user manual for
detailed operational instructions.
SLH side carrier
Thank you for choosing this premium product from SW-MOTECH. Please carefully
read and understand all instructions, safety messages, and warnings in this
mounting instructions prior to installation and use of this product to avoid
injury.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Visit our webshop for additional information, such as
application charts and PDF mounting instructions. Any other documents that may
be required (e.g. ABE certifications), are also available for download at our
website. Keep these mounting instructions as a reference.
SW-MOTECH assumes no liability for damage caused by improper installation
and/or maintenance work!
SAFETY ALERT SYMBOL
This safety alert symbol is used throughout these mounting instructions to warn of the possibility of death, bodily injury or other warnings. The words DANGER, WARNING, and CAUTION are used with this safety alert symbol to convey important safety messages and information related to the installation and use of this product. These words along with the safety alert symbol mean:
-
DANGER: Indicates a hazardous situation that, if not avoided, will result in death or serious injury!
-
WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury!
-
CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury!
-
NOTICE: Important information, but not death or injury-related (property damage only)!
-
A WARNING: The installation and/or maintenance of this product requires advanced mechanical skills, the proper tools, and a thorough understanding of tool use and torque specifications.
For your own safety, SW-MOTECH recommends having installation and/or maintenance carried out by a qualified and certified motorcycle mechanic. -
A WARNING: Should you choose to self-install this product, carefully and completely read all installation and safety instructions before installation and use, and follow all the directions and safety precautions given in the mounting instructions to avoid serious injury or death. Also pay attention to all relevant information in the vehicle manual during installation and use. IF YOU DO NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS OR NEED CLARIFICATION OF ANY INSTRUCTION, DO NOT ATTEMT TO MOUNT THIS PRODUCT WITHOUT CONTACTING SW-MOTECH FOR ASSISTANCE.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included.
- CAUTION: Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the engine/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools and wear always safety glasses and hand protection. Have another person help you.
- MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer’s specifications or replaced by parts and hardware delivered by SW-MOTECH.
- WARNING: Secure all threads, unless otherwise specified, with a mediumstrong strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a certified motorcycle workshop!
- FUNCTION CHECK: After installation also make sure that no moving parts are obstructed, and the function of the vehicle is not hindered in any way. Cables and hoses must not rub and/or be pinched.
- WARNING: Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all connections and the proper fit of the product. Installed accessories can change the driving behavior/stability of the vehicle.
PARTS LIST
Note: All measurements are in millimeters. b The second number indicates the total quantity of the part in the delivery. c No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
Note: All measurements in millimeters. b The second number indicates the total quantity of the part in the delivery. c No torque specifications: Use the torque defined by the vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
- WARNING: Always wear eye and hand protection!
- WARNING: Always use appropriate tools!
- Remove the shown screws on the right side of the vehicle.
Attach the countersunk part (2) to ‘ the carrier bracket (11, as shown in the drawing.
- WARNING: Use a liquid thread locker!
- Tighten the screw as specified.
- Attach the carrier bracket (11 on the right side to the vehicle.
- WARNING: Use a liquid thread locker!
- Tighten the screws as specified.
- WARNING: Always wear eye and hand protection!
- WARNING: Always use appropriate tools!
- Remove the shown screws on the left side of the vehicle.
- attach the stopper spacer [12) as shown to the carrier bracket [11); then insert the plastic plug [14).
- A WARNING: Use a liquid thread locker!
- Tighten the screw as specified.
- Mount the carrier bracket[11 I to the left side of the vehicle as shown.
- WARNING: Use a liquid thread locker!
- Tighten the screws as specified.
- WARNING: Always wear eye and hand protection!
- WARNING: Always use appropriate tools!
- Remove the shown screws on the left side from the ve
- Attach the stopper spacer (27) to the spacer bracket (26), as shown in the detailed drawing.
- Tighten the screw as specified.
- Attach the carrier bracket (20) and the spacer bracket (26) to the left side of the vehicle.
- WARNING: Use a liquid thread locker!
- Tighten the screws as specified. Tighten the screw (31 I with the manufacturer · specified torque.
- Then insert the plastic plug (33) into the opening of the stopper spacer (271.
PRODUCT SPECIFIC INFORMATION
WARNING: It is essential to observe the country-specific regulations regarding
the lighting equipment (reflectors)!
If the reflectors mounted to the vehicle in the factory setting are covered by
the side carriers, the reflectors must be removed and/or attached elsewhere in
the same mounting position!
& NOTICE: Observe the country-specific regulations concerning vehicle
registration/operation as well as TOV regulations if applicable. If required,
register installed parts in the vehicle documents through an appropriate
inspection authority.
Legend Gear side case LH1 / LH2
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at our website.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers” accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behavior and/or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle
registration/operation as well as TUY regulations if applicable. If required,
register installed parts in the vehicle documents through an appropriate
inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all
items of the parts list are included. Make sure that your vehicle is parked
safely and cannot fall over. Turn off the engine and remove the ignition key.
Let the motor/ exhaust cool off if necessary. Disconnect the vehicle battery
when working on the electrical system. Use appropriate tools. Have another
person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE
the first use, that the product can be fixed properly and used without
problems with your vehicle type. After fixation also make sure that no moving
parts are obstructed and the function of the vehicle is not hindered in any
way. Lamps as taillights and turn signals must not be limited in their
function. Cables and hoses must not rub and/or be pinched. Before starting to
ride, perform a comprehensive check of all functions.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycle driving and
braking performance!
ATTENTION: Before riding and at each stop (every 200 km) check proper fixation
of the product!
ATTENTION: The maximum load must not be exceeded! The maximum vehicle load specified by the manufacturer must not be exceeded
SW-MOTECH GmbH & Co. KG
- Ernteweg 7-10 · 35282 Rauschenberg · Germany
- Tel. I phone+ 49 [0)6425 / 8168 – 050
- Fax/ fax+ 49 [0)6425 / 8168 – 10 info@sw-motech.com • www.sw-motech.com
PARTS LIST & CARE
CARE
Clean the product periodically or after each trip, as dust and dirt have a
wear-effect and permanent stains can be prevented. Clean the product after
riding in salty conditions, to avoid damage from salt.
First remove dust and encrustations with a soft dry brush. Remove stubborn
deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning
agents, rough cleaning tools or high pressure washer! Then rinse with clear
water.
Before re-use dry the product for at least 24 hours in the air (not in direct
sunlight).
FIXATION
- Assemble the components as shown in the drawing.
- Pay attention to the side-specific alignment of the bolt, as emphasized in the schematic drawing . ATTENTION: Use liquid threat locker!
- Tighten the screw as specified.
- Loop the string as shown.
- NOTE: The BC.LDC.00.682. 1000• f•J is sold seperately.
- Disassemble the components and attach them to to bags lid as shown.
- Hangen Sie die Tasche (1) in die am Fahrzeug verbaute Aufnahme ein.
- Achten Sie darauf, dass beide Halteelemente vollstandig in die Aufnahmekonturen des Anbaublechs eingehakt sind.
- Hang the bag [1 I into the sockets of the mounting bracket attached to your vehicle.
- Pay attention that both retaining elements are completely hooked into the socket contours of the mounting bracket.
- Secure the bag [1) with the quick turn fastener [3), by inserting it into the opening and turning it clockwise.
- Pay attention to the audible clicking sound.
- The inserting position of the quick turn fastener differs depending on the vehicles· side.
- Attach the string of the quick turn fastener to the loop on the inside of the bag.
- ATTENTION: Before each ride, lock the lid of the bag.
- Thoroughly clean the front of the lid from grease and dirt.
- Attach the reflector [4) to the lid as shown in the drawing.
MOUNTING INSTRUCTIONS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>