UNTITLED 9160748 Mini LED Triangle Light Instruction Manual

Mini LED Triangle Light
INSTRUCTION MANUAL

READ AND UNDERSTAND THIS INSTRUCTION MANUAL PRIOR TO USING THIS PRODUCT, FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH.
Keep this instruction manual for future reference.

IMPORTANT SAFETY INFORMATION

Read and understand this instruction manual before using this product. Failure to do so COULD result in death or serious injury.
This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and troubleshooting steps described within to ensure your safety and satisfaction. The contents of this instruction manual are based upon the latest product information available at the time of publication.
The manufacturer reserves the right to make product changes at any time without notice.
The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating, maintaining and cleaning power equipment.
Always use common sense and pay particular attention to all the DANGER, WARNING, CAUTION and NOTICE statements of this manual.

WARNING SYMBOLS AND DEFINITIONS

****| This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
---|---
| Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
| Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
| Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
| Addresses practices not related to personal injury.

UNPACKING & INSPECTION

When unpacking, please inspect the product carefully to endure the product is intact and undamaged.
Do not operate this product if damaged during shipment, handling or misuse. Do not operate the LED Off-Road Work Light until the parts have been replaced or the fault rectified. Failure to do so may result in serious personal injury or property damage.

GENERAL SAFETY RULES

READ ALL SAFETY WARNINGS, INSTRUCTIONS, ILLUSTRATIONS AND SPECIFICATIONS PROVIDED WITH THIS PRODUCT. Failure to follow all instructions listed below may result in serious injury OR PROPERTY DAMAGE.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.

• Use the right tool or attachment for the job.
  There are certain applications for which this product was designed. Do not modify this product, and do not use this product for purposes for which it was not intended.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

• Keep children and bystanders away while working. Distractions can cause you to lose control.

PERSONAL SAFETY

• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
• Stay alert, watch what you are doing and use common sense when using tools. Do not assemble and install this product while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while working may result in serious personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control in unexpected situations.

GENERAL SAFETY RULES

• Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

SERVICE

• Have your LED Off-Road Work Light serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.

This product is not intended for use by persons (including children) whose physical, sensory, or mental capabilities are different or reduced, or lack experience or knowledge unless such persons receive supervision or training in the operation of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not use the device as toys.

**** READ AND SAVE ALL INSTRUCTIONS FOR FUTURE USE

SPECIFIC SAFETY WARNINGS

  Proper installation of this product requires a good working knowledge of automotive electrical systems. If you have any doubts about properly installing this product, have a qualified technician install it. Neither the manufacturer nor the retailer is responsible for any damage, personal or property, incurred during installation or improper installation.

• Read all instructions and safety  precautions in the vehicle’s manual onto which the Off-Road Work Light will be installed.
• Do not install this product in any way that interferes with the deployment of air bags. Vehicles equipped with airbags may have the sensors located inside the front bumper. Make sure to consult the vehicle service manual to determine the location of the airbag sensors. To avoid damaging the sensors if they are located in the front bumper, do not drill holes in the bumper.
• Ensure all vital components of the vehicle are not in danger of being damaged by drilling holes necessary for installation. If drilling is required, check all sides of the mounting surface for any hidden electrical lines or cables before drilling any holes. Do not damage or weaken the structural integrity of the vehicle.
• Select a mounting location that will not restrict sufficient airflow to the radiator or obstruct headlights or turn signals of the vehicle.
• Clean mounting surfaces before installation using water, and if necessary. a 50/50 mix of water and isopropyl alcohol.
• Install on negative (-) ground 12/24 VDC systems only. Please follow all wiring guidelines provided to guarantee long lifespan. Failure to follow these instructions may result in damage to the product.
• The Off-Road Work Light is for OFF-ROAD use only. Follow local, state, and federal regulations regarding installation and use of this product on your vehicle.
• Use only as intended. Not for marine use. Do not mount underwater.
• During continuous operation lighting units can become extremely hot – Do not touch while operational or within 30 minutes of turning off. Do not place anything flammable near light during or after use.
• Keep wiring away from hot surfaces and moving parts.
• AVOID EYE INJURY – Do not lock directly into light as it may cause serious eye injury.
• To prevent damage, turn light off before starting or turning off the vehicle.
• Turn off the LED Off-Road Work Light. disconnect its power cord from its 12 Volt DC battery, and allow it to completely cool down prior to performing any inspection, maintenance, or cleaning on the unit.
• Inspect before every use; do not use if parts are loose or damaged.

NOTICE Save these instructions. Refer to them frequently and use them to instruct others who may use this product. If you loan someone this product, loan them these instructions also.
**** FOR OFF-ROAD APPLICATION ONLY. NOT INTENDED TO BE USED IN PLACE OF VEHICLE’S STANDARD LIGHTS/HEADLIGHTS.

CONTENTS

INSTALLATION

To prevent serious injury and  fire, connect wires with correct polarity.

To avoid accidental short circuits, disconnect the negative (-) terminal of the vehicle battery prior to installing the LED Off-Road Work Light.

INSTALLATION

1. Remove unit & included hardware from packaging.

2. Attach mounting bracket as shown:
   A) Place shorter bolt C through the opening in the base of the bracket B. This will be used to mount to the vehicle.
   B) The long bolt threads through the bracket and body A of the LED unit and is secured with a nut G, lock nut E, and washer F.

3. Attach positive wire securely to a 12-24V fused power source.
   • Extension of the wiring may be necessary.
   • Can be wired into a switch that will support the 0.71/0.31 A draw.

4. Attach black ground wire to a safe, clean ground location.
   • Use an appropriate wire terminal (not included) for a secure connection
   • Ensure ground wire is properly and safely attached.

CAUTION

• Waterproof all wiring connections  using heat shrink terminals. heat shrink tubing, electrical tape, or other appropriate methods (not included).
• Before connecting to a battery, ensure that the switch is in the OFF position.
• Use plastic cable ties (not included) to secure wiring throughout the vehicle.
• Avoid hot areas and moving parts when routing wires.
• Protect wiring from sharp edges with electrical tape, grommets, cable wrap or other appropriate means (not included).

MAINTENANCE

Always unplug the LED Off-Road Work Light from its DC power source and allow the unit to completely cool down before performing any inspection or maintenance.
BEFORE EACH USE, inspect the general condition of the Off-Road Work Light System. Check for misalignment or binding of moving parts, cracked or broken parts, damaged wiring. damaged lens, and any other condition that may affect its safe operation.
If a problem occurs with the Lights, have the problem corrected before further use. Do not use damaged equipment. Inspect:

• Loose fasteners
• Misalignment
• Binding of moving parts
• Damaged wiring
• Improper mounting
• Cracked or broken parts, and any other condition that may affect its safe operation.

If abnormal noise or vibration occurs while driving, Stop the vehicle and have the problem corrected before further use. Do not use a damaged work light.
Tag damaged unit “DO NOT USE’ until repaired by a qualified service technician.

CLEANING
Use only mild soap and a damp cloth to clean your LED Off-Road
Work Light since certain cleaning agents and solvents are harmful to Plastics and aluminum parts. Some of these include: gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing ammonia.

TROUBLESHOOTING

2. Wiring connections are loose.
3. Wiring is damaged or corroded.
4. Wires are not connected according to the correct polarity.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>