UNTITLED CLASS1 Bambu Lab 3D Printer User Guide
- May 15, 2024
- Untitled
Table of Contents
- CLASS1 Bambu Lab 3D Printer
- Component Introduction
- Accessory Specification
- AMS & Tool Head Unlock
- AMS Assembly
- Spool Holder Assembly
- Hot Bed Unlock & Screen Installation
- Printer Binding
- First Print
- Bambu Studio
- Specification
- Customer Support
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Bambul Lab X 1 Combo & X 1- Carbon Combo 3D Printer
Quick Start
CLASS1 Bambu Lab 3D Printer
Please review the entire guide before operating the printer.
- Safety Notice: Do not connect to power until assembly is complete.
Bambu Studio & Bambu Handy
https://bambulab.com/download
*Warning:
The AMS supports spools with a width of 50-68mm.
When operating the AMS, we recommend using Bambu Filament, which has been
thoroughly tested to work with the AMS. Please make sure to avoid using soft
materials like TPU or damp PVA, as they can get stuck in the AMS, and please
avoid using cardboard spools as the spool may slip. If you run into any issues
with specific filaments, please let us know so that we can provide better
advice to our community.
Component Introduction
Accessory Specification
AMS & Tool Head Unlock
Take out
the accessory box. Use Allen Key H2 to remove the screws as pictured.
Take out the AMS by sliding it out through the top.
*We recommend using the short end of the Allen Key to unlock the screws more easily.Remove the four screws as the arrows indicate.
Take out the AMS cushioning. Remove the carboard from the tool head.
Romove the foam from the excess chute.
AMS Assembly
Spool Holder Assembly
Remove the screw as pictured with an Allen Key H2.
Secure the spool holder with two screws from the accessory box.
Hot Bed Unlock & Screen Installation
Remove the three screws with an Allen Key H2 to unlock the hot
bed.
Pull the Flexible Printed Circuit (FPC) out about 50mm.Insert the FPC into the port by pressing the terminal as
pictured.
Insert the screen back to the slot on the printer, then lock it by pushing it
to the left.
Printer Binding
- Download the Bambu Handy App. Register and log in to your Bambu Lab account.
- Connect the printer to power. Follow the instructions on the screen until getting to the page shown on the right side.https://www.bambulab.com/download
- Use Bambu Handy to scan the QR code on the screen, and bind your printer with your Bambu Lab account.
- Follow the instructions on the screen to complete the initial calibration.
It is normal to have vibration and noise during the calibration process.
DO NOT remove the protective foam from beneath the hot bed until after the initial calibration is complete.
First Print
Apply a thin layer of glue on the build plate.Place at least one spool of Bambu Filament into the AMS. Turn on
the power to start the printer and the AMS. Insert the filament into the
filament inlet. The filament will be automatically pre-loaded when detected.
We recommend first printing a single-color model with the supplied Bambu PLA Basic.
Press “ “internal”. Select a file to start the first print.
We recommend using one of the pre-loaded files as a first test print.
Bambu Studio
Download Bambu Studio: http://bambulab.com/downloadLog in to Bambu Studio with
your Bambu Lab account, which is the same for the Bambu Online store.
Create or open a project.Slice the model, select your printer and send the
model to print.
We recommend performing bed leveling before each print and performing flow calibration after changing filament.During printing, you can remotely monitor your print, or pause/stop printing on the “Device” interface.
The live view can be seen only if a camera is mounted.
Specification
Item | Specification |
---|---|
X1 -Carbon | X1 |
Printing Technology | Fused Deposition Modeling |
Body | Build Volume(WDH) |
Chassis | Steel |
Shell | Aluminum & Glass |
Tool Head | Hot End |
Extruder Gears | Hardened Steel |
Nozzle | Hardened Steel |
Max Hot End Temperature | 300°C |
Nozzle Diameter (Included) | 0.4 mm |
Nozzle Diameter (Optional) | 0.2 mm, 0.6 mm, 0.8 mm |
Filament Cutter | Yes |
Filament Diameter | 1.75 mm |
Hot bed | Build Plate |
Build Plate Surface(Included) | Bambu Cool Plate, Bambu Engineering Plate |
Build Plate Surface (Optional) | Bambu High Temperature Plate |
Max Build Plate Temperature | 110°C@220V, 120°C@110V |
Speed | Max Speed of Tool Head |
Max Acceleration of Tool Head | 20 m/s^2 |
Max Hot End Flow | 32 mmA3/s @ABS |
Cooling | Part Cooling Fan |
Hot End Fan | Closed Loop Control |
Control Board Fan | Closed Loop Control |
Chamber Temperature Regulator Fan | Closed Loop Control |
Auxiliary Part Cooling Fan | Closed Loop Control |
Air Filter | Activated Carbon Filter |
Supported Filament | PLA, PETG, TPU,ABS,ASA,PVA,PET |
PA, PC | Ideal |
Carbon/Glass Fiber Reinforced Polymer | Ideal |
Sensors | Bambu Micro Lidar |
Chamber Monitoring Camera | 1920*1080 Included |
Door Sensor | Yes |
Filament Run Out Sensor | Yes |
Filament Odometry | Optional with AMS |
Power Loss Recover | Yes |
Physical Dimensions | Dimensions |
--- | --- |
Net Weight | 14.13kg |
Electrical Requirements | Voltage |
Max Power | 1000W@220V, 350W@110y |
Electronics | Display |
Connectivity | Wi-Fi,Bambu Bus |
Storage | 4GB EMMC and Micro SD Card Reader |
Control Interface | Touch Screen, APP, PC Application |
Motion Controller | Dual-Core Cortex M4 |
Application Processor | Quad ARM A7 1.2 GHz |
Neural-Network Processing Unit | 2 Tops |
Software | Slicer |
Support third party slicers which export standard
G-code such as Superslicer, Prusaslicer and Cura,
but certain advanced features may not be supported.
Slicer Supported OS| MacOS, Windows
Wifi| Frequency Range| 2400MHz-2483.5MHz
Transmitter Power (EIRP)| ≤ 21.5dBm(FCC)
≤ 20 dBm (CE/SRRC)
Protocol| 802.11 b/g/n
Laser (Either)| Laser
(CLASS 1)| Wavelength| 850nm, 850nm
Maximun Output of Laser Radiation| <0.778mW
Laser
(CLASS 2)| Wavelength| 405nm, 808nm
Maximun Output of Laser Radiation| <1mW
Bambu Studio
Bambu Handy
https://bambulab.com/download
Customer Support
Please visit the Bambu Lab Wiki for more setup and maintenance tutorials.
https://wiki.bambulab.com/en/home
https://wiki.bambulab.com/en/home
If you need support, please try either of the two approaches:
Approach 1: Create a support ticket on the Official Website
Approach 2: Create a support ticket on the Bambu Handy App
Enjoy!
www.bambulab.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>