UNTITLED 18707A Ceiling LED Lamp Light User Manual

UNTITLED 18707A Ceiling LED Lamp Light

Dear Customer! Thank you for purchasing our product, we hope you will use it with satisfaction for a long time!

Product Description

• A circular lamp that illuminates the required room with adjustable color temperature LEDs. The lamp can be easily installed on a ceiling, plasterboard surface, or even on a side wall with the help of the attached bracket.
• The round shape gives the room a modern and clean look, while the discreet white color fits harmoniously into most interiors. Energy-saving LED technology offers an economical solution with a long service life and low energy consumption.
• Without the need for completeness, it can be ideal for corridors, stairwells, utility rooms, hallways, etc. lighting.
• Choose this practical and elegant solution for comfortable and efficient lighting of your rooms!
• Compact, thin light fixture
• It can be installed on the ceiling and the sidewall
• It can also be installed in an existing plasterboard hole thanks to the adjustable bracket diameter
• Adjustable color temperature
• IP20 protection

With adjustable spring arms: 050-795 mm possible hole size

Mounting height:| Ceiling: 2,2-4 m

Wall: 1,8-2,5 m

Protection:| IP20 (Indoor)
Operating temperature:| 10-40 °C
Operating humidity:| <93% RH
Size:| 02JOx 19 mm
Material:| Plastic

Signs in the user guide

• This symbol warns of the risk of injury.
• This sign warns of the risk of injury from the use of electricity.

First use:

• Attention! The wiring and installation of the product should be carried out by a specialist, always following the electrical safety regulations and rules of the country in question.
• The connection to the electrical network must always be performed by a professional!
• De-energize the circuit before connecting!
• When installing the device, pay attention to the markings on the device. Use a cable with a cross-section suitable for the load!
• The manufacturer and distributor shall take no responsibility for damages and injuries resulting from improper installation!

Be careful when installing the device! When choosing the right place, please keep the following points in mind:

• 110-240 V AC 50/60 Hz network preparation is required for the correct operation of the device.
• The device can only be placed in an environment that meets the IP protection classification.
• Ensure proper insulation of cable connections.
• Place the device in such a way that the cabling does not come in contact with any water or cause condensation into the device.
• Do not install near heat sources. (near heating, cooling units, hobs, ovens)

Installation

• Remove the frame before installation.
• Depending on the type of wall, fix the metal bracket using dowels and screws of the appropriate size and type, or use the spring arms in the case of plasterboard.
• The spring members on the bracket (A) can be moved freely or even removed. The two mounting points on the lamp body are located (B) 212 mm apart, and they can also be used for mounting if required if the metal bracket cannot be fixed.
• (Note: These are just preparations, by thinning the device housing material.)
• Depending on the installation conditions, we recommend that you thread the cables through the middle hole (C) on the metal bracket, so that if you install the lamp without the spring members, it can still be installed completely flat.
• You can attach the lamp to the metal bracket by turning it counterclockwise.

Electrical wiring

• Also, thread the cables through the cable guide and remove the upper part of the cable holder.
• The cables should come from the central part of the device in the section designed for this purpose.
• Using a screwdriver, loosen the screws of the terminal block and connect the wires to the correct place, then tighten the screws.
• Replace the cable holder and secure the cable.

Input:

• L – phase (live wire)
• N – Neutral thread (0)
• Check for correct wiring.
• Set the desired LED color temperature. (In „Switch” mode, turning the external switch on and off, the device always lights up in a different color.)
• Place the lamp frame back on the device.
• Apply voltage to the device and test for correct operation.

WARNINGS

General advice:

• The danger of suffocation! Please keep the packaging of the device away from children, as it may lead to suffocation.
• The device can only be used by adults, the storage location must be chosen in such a way that children cannot accidentally access it.
• Children must not play with the device.
• The device may only be used for its intended purpose! The device may only be used by persons who have read and understood this user manual and can operate the device accordingly!
• Persons with reduced mental, physical, or sensory abilities may not use the device! Children must not use the device!
• Do not use the device if it has previously been dropped or bumped against something and it is visibly damaged! Safety devices must be used as intended, their modification or elimination is strictly prohibited!
• Do not operate it to connect a consumer with a higher power than specified.
• Use a chemical-free, soft, dry cloth to clean the device. Before cleaning, the device must be de-energized. Make sure that no liquid gets inside the device by accident.

The danger of electric shock

• Never change settings with wet hands or in a wet environment!
• Touching the device, including its cable, with wet hands is strictly prohibited! The device must only be connected to alternating current with the correct voltage.
• If you experience any damage, do not use the device, contact a specialist service! During use, take care of the integrity of the network cable, and avoid edges and objects that may cause damage to the surface of the cable.

Waste management (Electronic device)

• (Valid in the European Union and all other European states participating in a selective collection)
• According to directives 2012/19/EU, electrical waste and devices cannot be thrown away as household waste appliances must be collected in order to maximize the recycling of raw materials, thus reducing their impact on people’s health and the environment.
• The crossed-out bin symbol is on all products for which separate collection is mandatory.
• Consumers should check with their local authorities for more information.
• WWW.PHENOMLIGHT.COM

Documents / Resources

| UNTITLED 18707A Ceiling LED Lamp Light [pdf] User Manual
18707A Ceiling LED Lamp Light, 18707A, Ceiling LED Lamp Light, LED Lamp Light, Lamp Light, Light
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>