BEGA 84 980 Gobo Floodlight RGBW Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
BEGA 84 980 Gobo Floodlight RGBW
DIMENSION
Gobo floodlight RGBW
Instructions for use
Application
RGBW floodlight with G½ threaded connection for the projection of Gobo motifs.
Suitable for Gobo motifs in accordance with Rosco default size E. The
floodlight can be controlled by DALI colour light control (DT8, RGBWAF, xy).
The floodlight can be bolted together with any female thread G½ according to
ISO 228 supplied by others or to BEGA accessories.
Product description
- Luminaire made of aluminum alloy, aluminum and stainless steel
- BEGA Unidure® coating technology
- Clear safety glass
- Silicone gasket
- Projector lens with adjustable glass lenses. Suitable for Gobos with an outer diameter of 37.5 mm, a max. image diameter of 28 mm and a material thickness of max. 1 mm
- Rotation range of floodlight 350°
- Swivel range -20°/+100°
- Mounting bracket with G½ threaded connection
- Thread length: 14 mm
- Connecting cable X05BQ-F 5 G 1 mm²
- Cable length 1 m
- BEGA Ultimate Driver®
- Complies with flicker requirements by IEEE 1789,
- DIN IEC/TR 63158, DIN IEC/TR 61547-1
- LED power supply unit 200-240 V 0/50-60 Hz
- DC 176-264 V
- DALI-controllable (DT8, RGBWAF, xy) Number of DALI addresses: 1
- Basic insulation is provided between the mains and control cables
- BEGA Thermal Control®
- Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
- Safety class I
- Protection class IP 65
- Dust-tight and protection against water jets Impact strength IK06
- Protection against mechanical impacts < 1 joule
- r – Safety mark
- c – Conformity mark
- Wind catching area: 0.04 m²
- Weight: 2.8 kg
- Lighting technology
- Beam angle 14°-30°
Lighting technology
Beam angle 14°-30°
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage by DIN EN 61547. To achieve additional protection against e. g.
transients, etc. we recommend separate overvoltage protection components. You
can find them on our website at www.bega.com.
Installation
LEDs are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping. Screw the
floodlight G½ threaded connection firmly into the on-site G½ female thread or
BEGA accessory. G½ threaded connection torque = 40 Nm. Secure the screw
connection from loosening on site (if provided with locking screw S, see fig.
A). Check the earth conductor connection between the G½ threaded connection
and the on-site G½ female thread.
Adjust floodlight:
Undo the hexagon socket screw (wrench size 5 mm) and hexagon nut (wrench size
27 mm) and set the desired beam direction (see sketches B, C).
Torque:
- Hexagon socket screw = 7 Nm
- Hexagon nut = 35 Nm
Secure bolted connection Gß against loosening by tightening the hexagon socket
screws (wrench size 2 mm).
The electrical connection must be carried out with matching protection class and safety class, strain-relieved, with suitable connection terminals (not included in the scope of delivery) at the luminaire power supply cable. Observe the correct configuration of the connecting cable. Make the mains connection to the brown (L), blue (N) and green-yellow wires ( ). The control cables are connected via the two DALI-labelled wires white-red (wh-rd) and white-black (wh-bl). If these wires are not assigned, the luminaire will work with full light output.
Inserting a Gobo
Open the floodlight:
Loosen the locking pin (hexagon socket wrench SW 2.5) on the back of the
floodlight housing. Turn the lens cover clockwise and lift it off. To insert a
Gobo, adjust the knurled screw R4 of the gobo holder so that it is in line
with the knurled screw R3 below it. Loosen the three knurled screws R3, turn
the lens cylinder clockwise to the stop and lift it off. Remove the retaining
ring on the Gobo receptacle and insert the Gobo. Make sure to insert the motif
inverted and upside down. Align the Gobo according to the subsequent
floodlight position. Exact alignment is possible in the mounted position via
knurled screw R4 within a range of ± 22.5°. Insert the retaining ring (note
the locking lugs) and replace the lens cylinder, turn it clockwise as far as
it will go and tighten the three knurled screws R3 handtight.
Adjusting the Gobo motif size and focus: Switch on the floodlight.
The size and focus of the Gobo motif is adjusted by moving the lens holder.
Loosen the two knurled screws R1 and R2 and adjust the lens distance until the
desired size is reached. A larger lens distance will make the motif smaller, a
smaller distance will make it larger. Hand-tighten the knurled screw R1. Use
the second lens to adjust optimal focus and then hand-tighten the knurled
screws R2. The shields provided (with 20 and 30 mm apertures) are used to
optimise the degree of illuminance and sharpness. Place the shields on the
lens cylinder with the side lugs pointing outward to choose the right one.
Finally, insert the side lugs of the shield into the lens cylinder. The
desiccant pouch provided in the delivery must be placed inside the luminaire
to ensure max. service life of the electrical components. Remove the desiccant
pouch from the foil packaging and place it in the position marked by the red
information label immediately before finally closing the luminaire. Position
the lens cover on the floodlight housing so that the notches in the floodlight
housing and the lens cover are congruent. Screw on the lens cover clockwise
until the stop. Screw on the locking pin (hexagon socket wrench size 2.5) on
the back of the floodlight housing.
Gobo motifs
Gobos made of metal or glass for insertion into the luminaires are not part of
the scope of delivery. You can find or individually order a large selection of
Gobo motifs or have them customised to your specifications in the
corresponding sizes at www.emea.rosco.com. When placing an order, please enter
the BEGA article number 84 980 as a reference. For Gobo masks with text or
logos, we recommend a maximum image width of 24 mm.
Maintenance
The connecting cable must be checked for external damage and may only be replaced by a qualified electrician.
Lamp
- Module connected wattage 15.6 W
- Luminaire connected wattage 18 W
- Rated temperature ta = 25 °C
- Ambient temperature ta max = 35 °C
- Module designation LED-1265/RGBW
- Colour temperature of the white LED 4000 K
- Luminaire luminous flux 196 lm
- Luminaire luminous efficiency 10,9 lm / W
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire. The
light colour and light output of BEGA replacement modules correspond to those
of the modules originally fitted.The module can be replaced by qualified
persons using standard tools. Disconnect the system. Loosen the locking pin
(hexagon socket wrench SW 2.5) on the back of the floodlight housing. Turn the
lens cover clockwise and lift it off. Undo the 4 mounting screws of the lens
unit (Torx drive T20) and remove the complete lens unit. Replace LED module.
Please follow the installation instructions for theLED module. Replace and
secure the lens unit. Switch on the floodlight, check the Gobo motif size and
focus, and adjust as needed. Position the lens cover on the floodlight housing
so that the notches in the floodlight housing and the lens cover are
congruent. Srew on the lens cover clockwise until the stop. Screw in the
locking pin.
Accessories
- 70 214 Pole cap for pole top ø 48 mm
- 70 248 Pole cap for pole top ø 60 mm
- 70 249 Pole cap for pole top ø 76 mm
- 70 229 Pole cap for pole top ø 82 mm
- 71 042 Adapter for installation on a pole
- 70 379 Cross-beam
- 70 221 Mounting box for anchorage unit
- 70 217 Mounting box ø 110 mm
- 70 294 Mounting box ø 130 mm
- 70 284 Mounting box ø 150 mm
- 70 245 Mounting box · rectangular
For the accessories, separate instructions for use can be provided upon request.
Spares
- Shield ø 20 mm 16 006 501
- Shield ø 30 mm 16 006 502
- Lens cover graphite 25 000 165
- Lens cover silver 25 000 166
- LED power supply unit DEV-0418/225i
- LED module LED-1265/RGBW
- Gasket cover 83 000 521
- The gasket Lens cover 83 001 952
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
Specifications
- Module designation: LED-1265/RGBW
- Color temperature of the white LED : 4000 K
- Luminaire luminous flux : 196 lm
- Luminaire luminous efficiency : 10.9 lm/W
- Lamp Module connected wattage : 15.6 W
- Luminaire connected wattage : 18 W
- Rated temperature: 25°C to 35°C
- Ambient temperature: max 70°C
FAQ
How do I order Gobo motifs?
You can order Gobo motifs or customize them at
www.emea.rosco.com using the BEGA article number
84 980 as a reference.
Can I replace the LED module myself?
Qualified persons can replace the LED module using standard tools. Ensure
the replacement module matches the original in light color and output.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>