VEVOR BY-70PF Ice Maker User Manual

VEVOR BY-70PF Ice Maker

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before operating the machine for the first time.

CAUTION :
ICE CAN’T BE STORED IN THE ICE BIN DURING NIGHT-TIME, IT’S NOT A FRIDGE, AND ICE WILL BE MELTED TO WATER AND FLOW OUT OF THE MACHINE.

1. If connected with water supply, CAUTION: must connect the potable water supply;
2. The machine is intended to be used in household and similar applications such as:
3. staff kitchen areas in shops, offices and other working environments;
4. farmhouses
5. by clients in hotels, motels and other residential-type environments;
6. Catering industry and similar non-retail industry.
7. The machine should be used in households without obstacles surrounded, good ventilation place. There is must be 15cm at least between the four sides of the machine with the wall.
8. When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance.
9. Don’t operate this or any other appliance with a damaged cord.
10. Connect to properly polarized outlets only. No other appliance should be plugged into the same outlet. Be sure that the plug is fully inserted into the socket.
11. Don’t place the machine and power cord near flammable material. Do not cover the cord. Do not submerge it in water.
12. We do not recommend the use of an extension cord,as it may overheat and become a risk of fire.
13. Unplug the ice maker before cleaning or making any repairs or servicing.
14. Exercise caution and supervision when the appliance is used near children.
15. Don’t use your ice maker outdoors.Avoid direct sunlight and make sure that there is at least 5 inches of space between the back and sides of your unit and the wall.
16. Don’t use any liquid other than water in the unit to make the ice.
17. Do not clean your ice maker with flammable detergents. The fumes can create a fire hazard or explosion.
18. Do not tip the machine over.
19. If the ice maker is brought indoors from outdoors during the wintertime, give it a few hours to warm up to room temperature before plugging to a power source.
20. This unit should be properly grounded for your safety. The power cord is equipped with a three-prong plug which mated with standard three-prong wall outlets to minimize the possibility of electric shock.
21. Plug your appliance into a dedicated,properly installed and grounded wall outlet.Do not,under any circumstance power and /or grounding should be directed toward a certified electrician.
22. The foaming materials inside is combustible which must be kept away from fire.
23. It’s forbidden to pull the cable to unplug the plug,pull the plug is a must.

Explosion diagram

1. visible door
2. door frame
3. top cover
4. blue light board
5. back panel
6. front panel
7. display board
8. light board
9. board cover
10. inner tank
11. water tank
12. evaporator
13. float
14. pump
15. compressor
16. DVfan
17. condenser
18. mainboard cover
19. mainboard
20. mainboard box
21. rubber feet

WARNING : This appliance must be grounded.

1. The fuse on the PCB is 8A (220V machine), if 110-120V machine, the fuse is lSA, if change, must be operated by a technician.
2. voltage fluctuation can’t be exceeded ±10% than rated voltage,or a Voltage stabilizer is needed.

IMPORTANCE : To avoid hazards due to instability, the unit must be placed on an even and flat surface.

Package Contents

Ice Maker Machine x 1

Warm Tips: Check whether all below accessories are there

OPERATING PROCEDURES

UNPACKING YOUR ICE MAKER

1. Remove all exterior and interior packaging materials. After you unpack the machine, we recommend you to leaving it for 24 hours before turning it on.
2. Clean the interior with lukewarm water and a soft cloth or clean the unit using the Self-Clean function.
3. Find a location for your ice maker where it’s protected from direct sunlight and other sources of heat (i.e. stove, furnace, radiator). Place the ice maker on a level surface. Make sure that there is at least 5 inches of space between the back and sides of your ice maker and the wall.
4. Allow one hour for the refrigerant to settle before plugging the unit for initial use.
5. The appliance must be positioned where the plug is accessible.

CONNECTING YOUR ICE MAKER WTTH OTHER PARTS
Please connect your ice maker with other parts by referring the diagram bel

Connect drainage pipe and water intake pipe

Warning:

1. The machine can only connect with drinking water sources, and must meet local drinking water standards |
2. The water pressure must be in 0.1-0.4Mpa, if exceeds 0.4Mpa, a pressure-reducing valve must be connected.
3. Drainage:The outlet of the drainage pipe must be lower than the outlet on the machine

Connect to the filter

MACHINE OPERATIONS

Operation Panel

Ice making operation

ON/OFF BUTTON:
Press this button under standby mode( display “–“)to make the machine to work,press the button for 2 seconds during working time,the machine will be powered off.

Cleaning/Reservation:

• Long press this button for 3s under standby mode to make enter cleaning mode for Smin and with the cleaning indicator is on.And it will enter standby mode after cleaning.
• Press the cleaning button during cleaning mode to make the machine end the cleaning in advance.
• Press this button under standby mode with the reservation indicator Flicker. and the “+”/”-” button to set the auto-turning-on time (in hoursfrom 0-23h). The machine will automatically turn on after The countdown is finished. and the “+” /” -” button to set the auto-turning-off time (in hours from 0-23h). The machine will automatically turn off after the countdown is finished.
• If we succeed in the reservation,the reservation light will be always on.
• Press the reservation button to cancel the reservation and the reservation indicator will be off.

HOT:
You can long press the “Hot” button 3 seconds during the ice making to make the ice cubes drop from the ice mold ahead of time.
Press “HOT” to turn off the blue light, press again to turn it on.

“+”and”-” button:
Through”+”/”-” to increase or decrease ice-making time or set the auto- turning-on/ off time,the “thickness adjust” indicator will be always on.
Ice making time can be adjusted from -8 to 8min.(e.g. if display 15, press “-” to adjust to -2,will display 13, that means,ice making time was adjusted to 13min)

Min/H:
Display ice-making countdown time (in minutes), display increase or decrease ice-making time (in minutes), display reserve auto-turning-on/off time (in hours)

CLEANING & MAINTENANCE

CLEANING
Please thoroughly clean your ice maker before initial use.

Exterior : the outside of the ice maker should be cleaned regularly with a mild detergent and warm water. Always use a soft cloth to avoid scratching or damaging the housing.
INTERIOR : please use the following Self-Clean function:

1. Add water and vinegar or lemon juice mix (1:1 ratio)
2. Plug in the unit, press and hold the CLEAN button for approximately 3s seconds,then release.The unit will automatically enter the Self-clean program. This process takes about 5-6 minutes.When the Self-Clean program is finished,unit will automatically power off.
3. The fan blade will be rotating. This process rinses the inside parts several times.
4. After the Self-Clean program is completed, unplug the power cord and drain out the water by unplugging the drain cap on the side. Replace the drain cap.
5. Add fresh water to the water reservoir,up to the water level mark.
6. Plug the unit and repeat the Self-Clean process by repeating steps 3 to 5. This will rinse out the vinegar/lemon residue.
7. After draining the water, replace and tighten the drain cap.
8. Dry the interior and exterior with a clean,soft cloth.

NOTE : It is strongly recommended to clean the unit before initial use or after the unit has not been in use for a long period.

MAINTENANCE

Pump cleaning
The pump must be cleaned once a week. Unplug the machine before cleaning, take out the pump from the tank, clean the inlet of the pump with a small brush, and install it back after cleaning.

Special instruction:

1. The machine will detect the around ambient temperature and set the ice-making time automatically.
2. The system will get to normal after 3 cycles.
3. The user can choose their desired size through the”+” and”-” buttons.
4. As the production of ice cubes increases, the plastic panel inside the machine (shown above) might be pressed down by the ice cubes. When the plastic panel is pressed down, the machine will stop producing ice cubes automatically and the “stoppage”indicator will light on. Please clean out the ice cubes regularly for the continuation of ice making.

Common malfunction analysis

El

| The ice full indicator is on,and the proximity switch didn’t react| The evaporator connector didn’t           Re-install the connector assembled well

The proximity switch is not sensitive      Replace the switch The connector didn’t return to    Take away the ice to make the

original position                            connector return to the original position

---|---|---

E2

| Normal to make ice| Stop every 4 cycles, and the         Proximity switch is the process of ice drop continues not sensitive, replace it for 5 min

No water in the tank

| __The water tank is not plugged      Put the plug back Use tap water as the water source    Check the water supply
Water pressure is too high, water floats Use tap water as the water source can’t work. Adjust the water pressure

or replace by a new one.

Water in the tank| Pump is badly clogged up, replace or

No water or low flow                     clean it

The spray pipe is clogged up,clean it

 |

Water flow and water get cool

| __Thin ice on the evaporator           Increase the making time through “+”  very solid ice on the evaporator   Reduce the making time through “-”

Some water sprayed to ice             Adjust the spray pipe

storage tank

The water leak from the back of      The tank need to be adjusted.

water tank

E2|

Water flow down but water is not cool

The fan is not work

| The main board didn’t supply      Replace by a new main board electricity to compressor

Compressor didn’t work                 Check the starter,replace by a new

one if needed

Compressor is very hot               Replace Compressor work but the

connected copper pipe didn’t         The compressor leak

get cool

The condenser prob is not           Unplug the prob or replace by a new sensitive                                    one

The fan is jammed                       Adjust the fan

Fan is broken                                Replace by a new fan

E3

E4| Ice full| The connector didn’t return to    Take away the ice to make the original position                         connector return to original position

E-mail ：support@vevor.com
E-mail：support@vevor.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>