BEGA 84 852 Surface Floodlight UniLink Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
84 852 Surface Floodlight UniLink
**Instruction Manual
**
84 852 Surface Floodlight UniLink
Technical amendments reserved
Surface floodlight BEGA UniLink®
Instructions for use
Application
Surface floodlight BEGA UniLink® with connection adapter for use in
combination with various accessories, e.g. for mounting on trees, pipes or
wooden structures.
A separate mains plug must be ordered in order to connect the floodlight to
the mains.
The various country-specific mains plugs with 0.5 m connecting cable, as well
as extension cables and five-way distribution boxes are available as
accessories.
Product description
Floodlight made of aluminium alloy,
aluminium and stainless steel
BEGA Unidure® coating technology
Colour graphite, silver or white
Safety glass with optical structure
Silicone gasket
Reflector made of pure anodised aluminium
Rotation range of floodlight 360°
Swivel range -35°/+90°
5 m mains supply cable
X05RN-F FEP 2 × 1◻ + 1G2,5◻ with
BEGA UniLink® plug-in connector
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V 50-60 Hz
BEGA Thermal Control®
Temporary thermal regulation to protect temperature-sensitive components
without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK07
Protection against mechanical impacts < 2 joule
****– Conformity mark
Weight: 2.8 kg
This product contains light sources of energy efficiency class(es) D
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
The manufacturer accepts no liability for damage caused by improper use or
installation. If subsequent modifications are made to the luminaire, the
person responsible for these modifications shall be considered the
manufacturer.
Total load
When configuring your lighting system, please ensure that the maximum power
consumption of 6 A is not exceeded. Information on power consumption can be
found in the instructions for use and data sheets for all BEGA UniLink
luminaires. Power consumption of 84 852: 0,16 A
Lamp
| Module connected wattage | 27.3 W |
|---|---|
| Luminaire connected wattage | 32.5 W |
| Rated temperature | t a= 25 °C |
| Ambient temperature | ta max= 40 °C |
84 852 K3
| Module designation | LED-0935/930 |
|---|---|
| Colour temperature | 3000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 4325 lm |
| Luminaire luminous flux | 3504 lm |
| Luminaire luminous efficiency | 107,8 lm / W |
84 852 K4
| Module designation | LED-0935/940 |
|---|---|
| Colour temperature | 4000 K |
| Colour rendering index | CRI > 90 |
| Module luminous flux | 4575 lm |
| Luminaire luminous flux | 3706 lm |
| Luminaire luminous efficiency | 114 lm / W |
Light technique
Broad spread light distribution.
Half beam angle 92/97°
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Caution:
The BEGA UniLink® plug connectors may only be connected and disconnected in a
voltagefree state.
Installation
Unscrew the hexagon socket screws (wrench size 3 mm) on the sides of the
connection adapter and screw the corresponding accessory to the floodlight.
Torque = 5 Nm.
Plug the floodlight’s connecting cable into the plug contact of the connecting
cable with the country-specific mains plug, or into the distribution box or
extension cable.
To ensure a sufficiently low protective conductor resistance (loop
resistance), the connecting cable of each luminaire in the system must not
exceed a length of 50 m from the entry point.
Adjustment of beam direction:
Undo joint screw (hexagon socket head wrench size 5 mm) and set the desired
beam direction.
Tighten the joint screw.
Torque = 7 Nm.
Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Maintenance
The connecting cable must be checked for external damage and may only be replaced by a qualified electrician.
Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.
Accessories
The following combination options are available for fitting to floodlights with connection adapter:
| 71 223 | Screw clamp with connection adapter |
|---|---|
| 71 224 | Tube clamp with connection adapter |
| 71 225 | Lashing strap with connection adapter |
| 71 226 | General fastener with connection adapter |
| 71 227 | G½ mount with connection adapter |
| 70 502 | Shield |
Country-specific mains plugs with 0.5 m connecting cable
| 71 180 | Plug type F / E: system common in Germany and Europe |
|---|---|
| 71 181 | Plug type G: system used in Great Britain (“Commonwealth plug”) |
| 71 182 | Plug type J: system common in Switzerland and Liechtenstein |
| 71 183 | Plug type L: system common in Italy and Greece |
| 71 184 | Plug type K: system common in Denmark and Greenland |
| 71 186 | BEGA UniLink ® Extension cable 5 m |
| 71 187 | BEGA UniLink® Extension cable 10 m |
| 71 188 | BEGA UniLink® Extension cable 20 m |
| 71 247 | Connecting cable 5 m with free line ends |
| 71 256 | Connecting cable 0.5 m with free line ends |
| 71 189 | BEGA UniLink® Five-way distribution box |
For the accessories a separate instructions for use can be provided upon request.
Spares
| Spare glass | 14 000 947 |
|---|---|
| LED power supply unit | DEV-0354/700 |
| LED module 3000 K | LED-0935/930 |
| LED module 4000 K | LED-0935/940 |
| Reflector | 76 001 173 |
| Gasket glass | 83 001 360 .A |
| Gasket housing | 83 001 871 |
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>